Use and Care Guide

ManualsBrandsDelta ManualsPlumbing ProductT13220-SHC

Para instalación fácil de su llave Delta

usted necesitará:

•LEER TODASlasinstruccionescompletamente

antesdeempezar.

•LEER TODOSlosavisos,cuidados,e

informacióndemantenimiento.

•Paracompletarelbordeylainstalaciónde

válvulasdentrodelasparedespreviaala

instalacióndelallaveysusaccesorios.

For easy installation of your Delta

faucet you will need:

•ToREAD ALLtheinstructionscompletely

beforebeginning.

•ToREAD ALLwarnings,care,andmaintenance

information.

•Tocompletethedeckandvalverough-inpriorto

installingthistrimkit.

Pour installer votre robinet Delta

facilement, vous devez:

•LIRE TOUTESlesinstructionsavantdedébuter;

•LIRE TOUSlesavertissementsainsiquetoutes

lesinstructionsdenettoyageetd’entretien;

•Installezlecorpsdurobinetetterminezle

pourtourdubainavantdeposerlesaccessories

definition.

Model/Modelo/Modéle

T2751&T4751

Dryden

™

Series/Series/Seria

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin:

SILICONE

Icons

1/8"(3.17mm)

3/32"(2.38mm)

1/8"(3.17mm)

3/32"

(2.38mm)

SILICONE

53405 53405 53405 53405 53405 53405

ASMEA112.18.1/CSAB125.1

ICC/ANSIA117.1

TWO HANDLE ROMAN TUB TRIM

LLAVE Y SUS ACCESORIOS

PARA BAÑERA ROMANA DE DOS

MANIJAS (MANERALES)

ACCESSOIRES DE FINITION DE

ROBINET À DEUX POIGNÉES POUR

BAIN ROMAIN

11/1/08Rev.E

Summary of content (8 pages)

PAGE 1
C ACCESSOIRES DE FINITION DE ROBINET À DEUX POIGNÉES POUR BAIN ROMAIN ® 53405 Model/Modelo/Modéle T2751 & T4751 Dryden™ Series/Series/Seria 53405 53405 53405 53405 ASME A112.18.1 / CSA B125.1 ICC/ANSI A117.1 53405 Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici. You may need/Usted puede necesitar/Articles dont vous pouvez avoir besoin: E 53405 SI LI C O N TE F LON 3/32" (2.
PAGE 2
Cleaning and Care Backflow Protection System Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel. Your Delta Faucet hand shower incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1/ CSA B125.1.
PAGE 3
Model / Modelo / Modèle T2751 ▲Specify Finish ▲ Especifíque el Acabado ▲ Précisez le Fini RP54012 Set Screw & Button Tornillo de Presión y Botón Vis de Calage et Bouton RP52593 Stream Straightener, Gasket & Wrench Enderezador del Chorro, Empaque y Llave Concentrateur de Jet, Joint et Clé RP54712 1 Red & 1 Blue Handle Button Not included with model 1 rojo y 1 azul botón de la manija no proporcionadas con el modelo 1 rouge et 1 bleue bouton de manette non fournis avec le modèle RP54096▲ Set Screw & Button T
PAGE 4
A. B. T4751 1 2 3 2 RP40668 Diverter Assembly Ensamble del Desviador Dérivation 3 2 1 1 Maintenance A. If faucet leaks from spout outlet–Shut off water supplies– B. Model T4751 If faucet does not divert water from the spout to the hand shower, check that the lift rod (1) is securely threaded into the diverter (2). If the problem persists remove the lift rod and spout. Replace the diverter assembly RP40668. Replace Seats and Springs (1).
PAGE 5
1 T2751 2 T2751 9 7 1 10 4 1 6 5 8 2 3 T4751 T4751 1 9 7 2 10 4 3/32" (2.38 mm) 3/32 po 6 1 5 8 3 NOTE: The deck and valve rough-in must be finished before installing the trim kit. 2 Place bases (1) with gaskets (2) over end valves (3) and secure with locknut (4). OPTION: Use silicone under the gasket if deck is uneven. Install gasket (5), base (6) and spout (7) on the spout adapter (8). Be sure spout is resting firmly on the deck.
PAGE 6
3 A. C. T4751 T4751 1 2 2 3 1 4 3 B. D. T4751 T4751 1 1 2 For Model T4751 Only A. Loosen set screw (1), remove finial (2) from lift rod (3) and install C. Slide hose (1) through conical nut (2). Attach hose (1) to braided B. Remove and discard the test cap and gasket (1). NOTE: This is an D. Install base (1) to nest (2) and tighten. OPTION: Use silicone metal hose (3) using gasket (4) and tighten. DO NOT install hand piece yet. lift rod.
PAGE 7
5 4 T2751 1 1 1 T4751 2 1 2 Install handles. Be sure glide ring (1) is properly seated in bottom of handle before installing. If either handle does not rotate in the correct direction, do the following: 1. Be sure that the end valves are installed correctly (with the hot valve on the LEFT and both inlet tubes installed AWAY from the spout). 2. Turn off the water supplies and remove the handle, bonnet nut, and stem unit. 3.
PAGE 8
6 A. B. T4751 T4751 2 1 3 1 2 For Model T4751 Only A. Pull hose (1) to its farthest extension and point it down into the B. Attach hand piece (1) to hose (2) with gasket (3) between tub. Pull the lift rod (2) up to the full on position and flush water lines for one minute. After flushing turn off water at the bath valve handles. Return the lift rod to the down position. connection. Refer to maintenance section (page 4) for correct diverter and lift rod function.