Installation Sheet

ManualsBrandsDelta ManualsTub FaucetsDelta Bowery Wall Mounted 2 Handle Tub Filler - Less Rough-In - Limited Lifetime Warranty

TWO HANDLE WALL MOUNTED TUB FILLER

FAUCET TRIM

GRIFO DE PARED DE DOS MANDOS PARA

LLENADO DE BAÑERA

GARNITURE DE VANNE DE REMPLISSAGE MURAL

À DEUX POIGNÉES

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

103613

Rough-in R3500-WL required for installation

Rough-in R3500-WL necesario para la instalación

Rough-in R3500-WL requis pour l'installation

1/8" (3.17mm)

www.deltafaucet.com

1-800-345-DELTA (3358)

customerservice@deltafaucet.com

103613

Specify Finish / Especifíque el Acabado / Précisez le Fini

Model/Modelo/Modèle

T5748-

Series/Series/Seria

Bowery

Para instalación fácil de su llave Delta

usted necesitará:

• LEER TODAS las instrucciones completamente

antes de empezar.

• LEER TODOS los avisos, cuidados, e

información de mantenimiento.

• Para completar el borde y la instalación de

válvulas dentro de las paredes previa a la

instalación de la llave y sus accesorios.

For easy installation of your

Delta

faucet you will need:

• To READ ALL the instructions completely

before beginning.

• To READ ALL warnings, care, and maintenance

information.

• To complete the deck and valve rough-in prior to

installing this trim kit.

Pour installer votre robinet

Delta

facilement, vous devez:

• LIRE TOUTES les instructions avant

de débuter;

• LIRE TOUS les avertissements ainsi que toutes les

instructions de nettoyage et d’entretien.

• Installez le corps du robinet et terminez le pourtour

du bain avant de poser les accessories de nition.

9/13/2018 1 103613 Rev. A

Summary of content (8 pages)

PAGE 1
03613 TWO HANDLE WALL MOUNTED TUB FILLER FAUCET TRIM GRIFO DE PARED DE DOS MANDOS PARA LLENADO DE BAÑERA Model/Modelo/Modèle T5748-pWL Series/Series/Seria BoweryTM GARNITURE DE VANNE DE REMPLISSAGE MURAL À DEUX POIGNÉES Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 A. C. 1 B. 1 1 Short Spout Shank Vástago del chorrocorto Tige de bec 2 Long Spout Shank Vástago de caño largo Tige de bec long 3 FLUSH YOUR SYSTEM A. Pull off plasterguards (1) and discard them. C. Turn on the water supplies to the valve body. Position a bucket in front of spout shank (1). Using pliers, slowly open the hot and cold valves, and allow the water to flow from the spout shank (1) for at least one minute. Close valves.
PAGE 3
2 A. 3A 1 Figure 1 3 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 2 1 2 1 3 2 Figure 1 2 3 1 Figure 2 B. Figure 2 1 2 3 1 2 2 1 SPOUT FLANGE AND SPOUT INSTALLATION 3 A. If the spout shank (1) is extending from finished wall more than 5/8", install flange (2) as shown in Figure 1. Screw spout nut (3) to the spout shank (1) and tighten it with wrench. If the spout shank (1) is sub flush or extending less than 5/8" from finished wall, install flange (2) and spout nut (3) as shown in Figure 2.
PAGE 4
3B Figure 3 2 4 3 1 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 3C Figure 5 1 2 4 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 3 3 3 1 1 2 4 4 Figure 4 4 Figure 6 Finished Wall 3/8" (9.5mm) 1 3 1 2 2 2 Finished Wall 3/8" (9.5mm) 1 4 3 1 3 3 2 1 1 2 4 HANDLE FLANGE INSTALLATION FOR FINISHED WALL THICKNESS VARYING FROM 1 1/4" TO 2 1/4". 4 HANDLE FLANGE INSTALLATION FOR FINISHED WALL THICKNESS VARYING FROM 2 1/4" TO 2 3/4".
PAGE 5
3D Figure 7 3 1 2 4 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 4 A. Finished Wall 1 3/8"-1 1/2" (35mm-38mm) 3 1 2 1 1 1 Cut off here Corte aquí Coupez ici 2 2 B. 2 C. 3 Black color ring Figure 8 1 2 Anillo de color negro Finished Wall 3/8" (9.5mm) Bague de couleur noire 2 3 1 3 1 2 Black color ring Anillo de color negro 4 Bague de couleur noire 1 HANDLE INSTALLATION Install stem extender (1) onto the cartridge. Mark the stem extender (1) between 1 3/8" - 1 1/2" from finished A.
PAGE 6
1 2 1 1 5 6 3 4 2 5 4 3 2 MAINTENANCE – SPOUT SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE OR SPOUT ASSEMBLIES If your faucet leaks at base of spout, replace spout tube adapter kit (1). A. Remove button and loosen set screw (2) on bottom side of spout and pull spout straight out to remove it from spout flange. B. Replace spout tube adapter kit (1). C. Reassemble in reverse order. If there is splashing from the spout outlet, remove the stream straightener (5) with wrench provided.
PAGE 7
▲ Specify Finish RP84244 Spout Flange, Gasket and O-ring Reborde del Surtidor, Empaque y Anillo “O” Embase de bec, joint et Joint torique Especifíque el Acabado Précisez le Fini RP100458 Long Mounting Sleeve and O-ring Manga de montaje larga y Anillo “O” Long manchon de montage et Joint torique RP100457 Spout Flange Assembly Reborde del Surtidor Embase de bec RP92255 Spout Tube Adapter Kit Juego de Adaptadores para Tubo de Chorro Kit d'adaptateur de Tube Bec RP100713▲ Spout Caño Bec RP100852 Glide Ri
PAGE 8
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.