Operating Guide

ManualsBrandsDelta ManualsBathtub FaucetsTrinsic Matte Black 2-Handle Residential Wall Mount Bathtub Faucet

Model/Modelo/Modèle

T5759-

Contemporary

TWO HANDLE WALL MOUNTED TUB FILLER

FAUCET TRIM

GRIFO DE PARED DE DOS MANDOS PARA

LLENADO DE BAÑERA

GARNITURE DE VANNE DE REMPLISSAGE MURAL

À DEUX POIGNÉES

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

For easy installation of your Delta faucet

you will need:

・

READ ALL

the instructions completely before

beginning.

・

READ ALL

warnings, care and maintenance

information.

・

To complete the deck and valve rough-in prior to

installing this trim kit.

Para instalación fácil de su llave Delta

usted necesitará:

・

LEER TODAS

las instrucciones completamente

antes de empezar.

・

LEER TODAS

los avisos, cuidados, e información

de mantenimiento.

・

Para completar el borde y la instalación de válvulas

dentro de las paredes previa a la instalación de la llave

y sus accesorios.

Pour installer votre robinet Delta

facilement, vous devez:

・

LIRE TOUTES

les instructions avant de débuter.

・

LIRE TOUE LES

les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

・

Installez le corps du robinet et terminez le pourtour du

bain avant de poser les accessories de nition.

102398

Rough-in R3500-WL required for installation

Rough-in R3500-WL necesario para la instalación

Rough-in R3500-WL requis pour l'installation

1/8" (3.17mm)

102398 Rev. A4/03/2018

www.deltafaucet.com

1-800-345-DELTA (3358)

customerservice@deltafaucet.com

102398

Specify Finish / Especifíque el Acabado / Précisez le Fini

Summary of content (8 pages)

PAGE 1
TWO HANDLE WALL MOUNTED TUB FILLER FAUCET TRIM 102398 GRIFO DE PARED DE DOS MANDOS PARA LLENADO DE BAÑERA Model/Modelo/Modèle T5759-pWL Contemporary GARNITURE DE VANNE DE REMPLISSAGE MURAL À DEUX POIGNÉES Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 A. C. 1 B. 1 1 Short Spout Shank Vástago del chorrocorto Tige de bec 2 Long Spout Shank Vástago de caño largo Tige de bec long 3 FLUSH YOUR SYSTEM A. Pull off plasterguards (1) and discard them. C. Turn on the water supplies to the valve body. Position a bucket in front of spout shank (1). Using pliers, slowly open the hot and cold valves, and allow the water to flow from the spout shank (1) for at least one minute. Close valves.
PAGE 3
2 A. 3A 1 Figure 1 1 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 2 3 2 1 3 2 Figure 1 2 3 Figure 2 B. 1 Figure 2 2 1 3 2 1 2 1 SPOUT FLANGE AND SPOUT INSTALLATION 3 A. If the spout shank (1) is extending from finished wall more than 5/8", install flange (2) as shown in Figure 1. Screw spout nut (3) to the spout shank (1) and tighten it with wrench.
PAGE 4
3B Figure 3 2 3 1 3C 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 4 Figure 5 1 2 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 3 3 4 3 1 1 4 Figure 4 2 4 2 Figure 6 Finished Wall 3/8" (9.5mm) Finished Wall 3/8" (9.5mm) 1 3 1 2 1 2 3 1 4 4 1 3 3 1 4 4 2 HANDLE FLANGE INSTALLATION FOR FINISHED WALL THICKNESS VARYING FROM 1 1/4" TO 2 1/4". 2 HANDLE FLANGE INSTALLATION FOR FINISHED WALL THICKNESS VARYING FROM 2 1/4" TO 2 3/4".
PAGE 5
3D Figure 7 1 4 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 3 2 A. Finished Wall 1 3/8"-1 1/2" (35mm-38mm) 3 1 2 1 1 1 4 2 4 Cut off here Corte aquí Coupez ici 2 B. Figure 8 Red color ring Marca de punto rojo Marquage rouge Finished Wall 3/8" (9.5mm) 1 C. 1 3 Marca de punto azul Marquage bleu 1 2 2 Blue color ring 2 3 3 1 4 HANDLE INSTALLATION Install stem extender (1) onto the cartridge. Mark the stem extender (1) between 1 3/8" - 1 1/2" from finished A.
PAGE 6
1 2 1 1 5 7 3 4 6 2 5 4 3 2 MAINTENANCE – VALVES SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE OR SPOUT ASSEMBLIES If your faucet leaks out of spout or around handle body, replace valve cartridge (1). A. Remove handle (2) by turning the base of handle counterclockwise by hand. B. Remove screw (3) and stem extender (4). C. Remove flange nut (5), handle flange (6). D. Remove mounting sleeve (7) and extender nut if present. E.
PAGE 7
▲ Specify Finish RP84244 Spout Flange, Gasket and O-ring Reborde del Surtidor, Empaque y Anillo “O” Embase de bec, joint et Joint torique Especifíque el Acabado Précisez le Fini RP100458 Long Mounting Sleeve and O-ring Manga de montaje larga y Anillo “O” Long manchon de montage et Joint torique RP100457 Spout Flange Assembly Reborde del Surtidor Embase de bec RP92255 Spout Tube Adapter Kit Juego de Adaptadores para Tubo de Chorro Kit d'adaptateur de Tube Bec RP100454▲ Spout Caño Bec RP100459 Short mou
PAGE 8
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.