Installation Guide

ManualsBrandsDelta ManualsBathtub FaucetsT5799-WL

Model/Modelo/Modèle

T5799-WL

Series/Series/Seria

Pivotal

TWO HANDLE WALL MOUNTED TUB FILLER

FAUCET TRIM

GRIFO DE PARED DE DOS MANDOS PARA

LLENADO DE BAÑERA

GARNITURE DE VANNE DE REMPLISSAGE MURAL

À DEUX POIGNÉES

Write purchased model number here.

Escriba aquí el número del modelo comprado.

Inscrivez le numéro de modèle ici.

You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:

For easy installation of your Delta faucet

you will need:

・

READ ALL

the instructions completely before

beginning.

・

READ ALL

warnings, care and maintenance

information.

・

To complete the deck and valve rough-in prior to

installing this trim kit.

Para instalación fácil de su llave Delta

usted necesitará:

・

LEER TODAS

las instrucciones completamente

antes de empezar.

・

LEER TODAS

los avisos, cuidados, e información

de mantenimiento.

・

Para completar el borde y la instalación de válvulas

dentro de las paredes previa a la instalación de la llave

y sus accesorios.

Pour installer votre robinet Delta

facilement, vous devez:

・

LIRE TOUTES

les instructions avant de débuter.

・

LIRE TOUE LES

les avertissements ainsi que toutes

les instructions de nettoyage et d’entretien.

・

Installez le corps du robinet et terminez le pourtour du

bain avant de poser les accessories de nition.

www.deltafaucet.com 4/24/2017 Rev. B

91206

Rough-in R3500-WL required for installation

Rough-in R3500-WL necesario para la instalación

Rough-in R3500-WL requis pour l'installation

1/8" (3.17mm)

Summary of content (8 pages)

PAGE 1
91206 Model/Modelo/Modèle T5799-WL Series/Series/Seria PivotalTM TWO HANDLE WALL MOUNTED TUB FILLER FAUCET TRIM GRIFO DE PARED DE DOS MANDOS PARA LLENADO DE BAÑERA GARNITURE DE VANNE DE REMPLISSAGE MURAL À DEUX POIGNÉES Write purchased model number here. Escriba aquí el número del modelo comprado. Inscrivez le numéro de modèle ici.
PAGE 2
1 A. C. 1 B. 1 1 Short Spout Shank Vástago del chorrocorto Tige de bec 2 Long Spout Shank Vástago de caño largo Tige de bec long 3 FLUSH YOUR SYSTEM A. Pull off plasterguards (1) and discard them. B. Replace the existing spout shank (1) with short spout shank (2) for finished wall thickness varying from 1/8" to 2 1/4", or long spout shank (3) for finished wall thickness varying from 2 1/4" to 3 3/4". C. Turn on the water supplies to the valve body.
PAGE 3
2 A. 3A 1 Figure 1 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 2 1 2 1 2 2 3 4 3 Figure 1 Figure 2 3 3 B. 1 Figure 2 2 1 1 2 3 2 1 3 SPOUT FLANGE AND SPOUT INSTALLATION A. If the spout shank (1) is extending from finished wall more than 5/8", install gasket (2) and spout flange (3) as shown in figure 1. Screw spout flange (3) to the spout shank (1) and tighten it with wrench.
PAGE 4
3B Figure 3 3 1 3C 1 1/2"-1 5/8" (38 mm-41 mm) Diameter Figure 5 3 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 1 3 2 3 2 1 4 4 2 Figure 4 1 3 2 Figure 6 Finished Wall 3/8" (9.5mm) 1 1 4 4 Finished Wall 3/8" (9.5mm) 1 3 1 2 2 3 3 4 4 1 4 2 4 1 2 HANDLE FLANGE INSTALLATION FOR FINISHED WALL THICKNESS VARYING FROM 1 1/4" TO 2 1/4". HANDLE FLANGE INSTALLATION FOR FINISHED WALL THICKNESS VARYING FROM 2 1/4" TO 2 3/4".
PAGE 5
3D Figure 7 1 4 1 1/2"-1 5/8" (38 mm-41 mm) Diameter 3 A. Finished Wall 1 7/16"-1 1/2" (36.5mm-38.1mm) 1 3 2 2 1 1 1 4 4 B. 2 Figure 8 Cut off here Corte aquí Coupez ici 2 Red marking Marca de punto rojo Marquage rouge 2 Finished Wall 3/8" (9.5mm) 1 1 3 1 3 4 5 2 Marca de punto azul Marquage bleu 3 HANDLE INSTALLATION A. Install stem extender (1) onto the cartridge. Mark the stem (1) between 1 7/16" 1 4 Blue marking - 1 1/2" from finished wall, remove and cut if necessary.
PAGE 6
1 2 1 9 5 8 4 1 7 3 6 4 5 3 2 2 MAINTENANCE – VALVES SHUT OFF WATER SUPPLIES BEFORE SERVICING VALVE OR SPOUT ASSEMBLIES If your faucet leaks out of spout or around handle body, replace valve cartridge (1). A. Remove button (2) and set screw (3). Pull off handle (4). B. Remove screw (5) and stem extender (6). C. Remove sleeve (7), handle flange (8). D. Remove mounting sleeve (9) and extender nut if any. E. Unscrew cartridge (1) by turning it counterclockwise using a 19 mm hex socket wrench. F.
PAGE 7
RP84244 Spout Flange, Gasket and O-ring Reborde del Surtidor, Empaque y Anillo “O” Embase de bec, joint et Joint torique ▲ Specify Finish Especifíque el Acabado Précisez le Fini RP92254▲ Spout Caño Bec RP92255 Spout Tube Adapter Kit Juego de Adaptadores para Tubo de Chorro Kit d'adaptateur de Tube Bec RP92252 Screws and Stem Extender (2) Tornillos y Extensión para la Espiga (2) Vis et Rallonge de tige (2) RP92251 Flange Nut and Flange (2) Tuerca con Reborde y Brida (2) Ecrou de l’embase et Embase (2)
PAGE 8
CLEANING AND CARE Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.