ASSEMBLY INSTRUCTIONS FOR THE DF4900L LINEAR BEARING SMITH MACHINE WITH LAT ATTACHMENT The DF4900L consists of the DF4900 Smith Machine and the DF830 Lat Attachment Attachment (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
DF4900 BOX CONTENTS A RH UPRIGHT QTY 1 B LH UPRIGHT QTY 1 C D RH REAR SUPPORT QTY 1 LH REAR SUPPORT QTY 1 E F G H RH FOOT QTY 1 LH FOOT QTY 1 CROSSMEMBER QTY 1 TOP FRAME QTY 1 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
DF4900 BOX CONTENTS I J K SMITH BAR QTY 1 GUIDE ROD QTY 2 WEIGHT SLEEVE QTY 2 L RH & LH SMITH BAR COLLAR QTY 1 EACH M N LH & RH GUIDE ROD COLLAR QTY 1 EACH RH & LH SAFETY CATCH QTY 1 EACH *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
DF4900 HARDWARE O RUBBER SHOE QTY 4 2” SQUARE CAP QTY 2 (factory installed) 1-3/4” ROUND CAP QTY 4 (factory installed) T S WEIGHT SLEEVE BOLT QTY 2 R Q P SET SCREW QTY 8 (factory installed) RUBBER DONUT QTY 2 U V M12 x 90MM BOLT QTY 20 M10 x 25MM BOLT QTY 8 W X Y Z M12 WASHER QTY 40 M10 WASHER QTY 16 M12 LOCKNUT QTY 20 M10 LOCKNUT QTY 8 AA BB CC CHROME SPRING QTY 2 HEX WRENCHES QTY 2 CORNER FLANGE QTY 2 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT
FRAME ASSEMBLY (NOTE: THE NUTS USED ON THIS PRODUCT ARE LOCK NUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE PLASTIC INSERT) DD B W Y U W D U O W A F W W U Y Y U W W W Y G W Y O E Y C W W O U W U ASSEMBLE THE LH FOOT (F), RH FOOT (E), CROSS MEMBER (G), AND THE LEFT AND RIGHT REAR SUPPORTS (C) AND (D), USING THE M12 x 92MM BOLTS (U), M12 WASHERS (W), AND M12 LOCKNUTS (Y). (LEAVE THE BOLTS HAND TIGHTENED AT THIS TIME) SLIDE THE RUBBER SHOES (O) ONTO THE RH AND LH FEET (E) & (F).
SMITH BAR ASSEMBLY LEFT SIDE ASSEMBLY HAS STOP PIN Z X L M X V ASSEMBLE LH SMITH BAR COLLAR (L) AND GUIDE ROD COLLAR (M) USING THE M10 x 25MM BOLTS (V), M10 WASHERS (X), AND M10 LOCKNUTS (Z). REPEAT FOR RH ASSEMBLY. A SLIDE THE ASSEMBLY ONTO THE SMITH BAR (I). REPEAT FOR RH ASSEMBLY.
GUIDE BAR INSTALLATION AA N AA R N R J J INSERT THE GUIDE RODS (J) INTO THE RETAINERS AT THE BOTTOM. SLIDE THE RUBBER DONUTS (R) ONTO THE GUIDE RODS AND MOVE TO THE BOTTOM. INSTALL THE RH AND LH SAFETY CATCHES (N) AND HOOK ONTO ONE OF THE CATCH PINS TO SUPPORT THE GUIDE RODS. SLIDE THE CHROME SPRINGS (AA) ONTO THE GUIDE RODS (J).
SMITH BAR ASSEMBLY MAKING SURE THAT THE HOOKS ARE FACING TOWARDS THE BACK, INSTALL THE SMITH BAR ASSEMBLY ONTO THE GUIDE BARS AND LOWER UNTIL IT RESTS ON THE SAFETY CATCHES. LIFT SMITH BAR, ROTATE BACKWARDS AND HOOK ONTO ONE OF THE BAR CATCH PINS. I K S INSTALL WEIGHT SLEEVE (K) WITH WEIGHT SLEEVE BOLT (S) ONTO SMITH BAR (I) AND TIGHTEN WITH SUPPLIED HEX WRENCH.
TOP FRAME INSTALLATION H INSTALL THE TOP FRAME (H) ONTO THE UPRIGHTS AND GUIDE RODS. CC U W DD W Y ATTACH THE TOP FRAME TO THE UPRIGHTS USING THE M12 x 92MM BOLTS (U), M12 WASHERS (W), MOUNTING FLANGES (DD), CORNER FLANGES (CC), AND M12 LOCKNUTS (Y). REPEAT FOR OPPOSITE SIDE. MAKE SURE ALL THE BOLTS ARE TIGHT BEFORE USING. CHECK THEM PERIODICALLY TO ENSURE THE BOLTS STAY TIGHT.
GUIDE BAR ADJUSTMENT THE GUIDE BAR RETAINERS ARE SLOTTED TO ALLOW FOR ADJUSTMENT. USING THE SUPPLIED HEX WRENCH, TIGHTEN THE SET SCREWS ON BOTH SIDES OF THE BOTTOM RETAINER. HOLD A LEVEL AGAINST THE GUIDE ROD TO ENSURE IT IS LEVEL. IF NECESSARY ADJUST THE SET SCREWS ON THE UPPER RETAINER. REPEAT FOR OPPOSITE SIDE.
ASSEMBLY INSTRUCTIONS FOR THE DF830 LAT ATTACHMENT (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
BOX CONTENTS A B TOP FRAME QTY 1 BOTTOM SUPPORT QTY 1 D C LOW BAR QTY 1 LAT BAR QTY 1 E F CABLE QTY 2 WEIGHT CARRIAGE QTY 1 I J 5” FLANGE QTY 2 4” FLANGE QTY 2 G REAR SUPPORT QTY 1 DF830 HARDWARE QTY 1 H FRONT SUPPORT QTY 1 DF830 INSTRUCTIONS QTY 1 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
HARDWARE K L M N RUBBER SHOE QTY 1 2” x 3” CAP QTY 1 REDUCER QTY 2 RUBBER BUMPER QTY 1 O P Q R 4-1/2” PULLEY QTY 4 3-1/2” PULLEY QTY 3 PULLEY BUSHING QTY 6 10” CHAIN QTY 1 S T U V M12 x 76MM BOLT QTY 4 M12 x 65MM BOLT QTY 5 M12 x 55MM BOLT QTY 4 M12 LOCKNUT QTY 15 W X M12 WASHER QTY 22 SNAP HOOK QTY 5 Y QUICK CLIP QTY 2 *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
FRAME ASSEMBLY V G H B W TOOLS REQUIRED: METRIC WRENCHES OR SOCKET SET INSTALL THE REAR SUPPORT (G) TO THE BOTTOM SUPPORT (B), ALIGNING HOLES IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (W) AND 12MM NUT (V) AND TIGHTEN. INSTALL THE FRONT SUPPORT (H) TO THE BOTTOM SUPPORT (B), ALIGNING HOLES IN FLANGE WITH PIN AND THREADED STUD. INSTALL 12MM WASHER (W) AND 12MM NUT (V) AND TIGHTEN.
FRAME ASSEMBLY (NOTE: THE NUTS USED ON THIS ARE LOCKNUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE PLASTIC INSERT.) O W V K W W O T W INSTALL THE 4 1/2” PULLEYS (M) INTO THE FRAME USING THE M12 x 55MM BOLTS (T), THE M12 FLAT WASHERS (W), AND THE M12 LOCKNUTS(V). INSTALL THE RUBBER SHOE (K) ONTO THE BOTTOM SUPPORT.
WEIGHT CARRIAGE ASSEMBLY M F M N INSTALL THE REDUCERS (M) INTO EACH END OF WEIGHT CARRIAGE (F). SCREW THE RUBBER BUMPER (L) INTO BOTTOM FLANGE.
FRAME ASSEMBLY INSTALL THE WEIGHT CARRIAGE ASSEMBLY ONTO THE REAR FRAME WITH THE WEIGHT BAR FACING FORWARD. SLIDE DOWN UNTIL IT RESTS ON THE RUBBER BUMPER.
TOP FRAME ASSEMBLY (NOTE: THE NUTS USED ON THIS ARE LOCKNUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE PLASTIC INSERT.) L A O V Q Q T P INSTALL THE 3-1/2” PULLEYS (P) INTO THE TOP FRAME (A) USING THE PULLEY BUSHINGS (Q), THE M12 x 65MM BOLTS (T), AND THE M12 LOCK NUTS (V). NOW INSERT THE 2” x 3” CAP (J) INTO THE END OF THE TOP FRAME (A).
FRAME ASSEMBLY W S V W INSTALL THE UPPER FRAME ASSEMBLY TO THE FRAME SUPPORTS WITH M12 x 65MM BOLTS (S), M12 WASHERS (W), AND LOCKNUTS (B).
FLOATING PULLEY ASSEMBLY (NOTE: THE NUTS USED ON THIS BENCH ARE LOCK NUTS, THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE PLASTIC INSERT.) V U O W U I ASSEMBLE THE FLOATING PULLEY ASSEMBLY USING THE 4 1/2” PULLEYS (O), THE 5” FLANGES (I), THE M12 x 55MM BOLTS (U), THE 12MM FLAT WASHERS (W), AND THE 12MM LOCKNUTS (V).
CABLE INSTALLATION WARNING: THE BAR CATCH IS MEANT FOR HOLDING THE BAR ONLY, NOT FOR BODY WEIGHT NOTE: BOTH CABLES ARE THE SAME LENGTH THE CHAIN ATTACHES TO THE BOTTOM CABLE BETWEEN THE CABLE AND THE ROW BAR. STARTING WITH THE CABLE END WITHOUT THE BALL, INSTALL UPPER CABLE OVER FRONT PULLEY, BACK TO MIDDLE PULLEY, DOWN TO TOP PULLEY OF FLOATING PULLEY ASSEMBLY, UP TO REAR PULLEY AND DOWN TO WEIGHT CARRIAGE. ATTACH SNAP HOOK TO END OF CABLE AND THEN TO WEIGHT CARRIAGE BRACKET.
FINAL INSTALLATION T T U U H H U Q U Q T T U U U U H H Q Q ATTACH THE LAT ATTACHMENT TO THE SMITH MACHINE USING THE M10 x 100MM BOLTS (Q), 4” FLANGE PLATES (H), M10 WASHERS (U) AND M10 LOCKNUTS (T). MAKE SURE ALL THE BOLTS ARE TIGHT BEFORE USE. REMEMBER TO CHECK THEM PERIODICALLY TO MAKE SURE THEY ALWAYS STAY TIGHT.
USE INSTRUCTIONS 1) SET THE SPOTTERS (9) TO THE DESIRED HEIGHT FOR A SAFE WORK OUT. 2) RAISE THE BAR AND ROTATE IT OUT UNTIL THE HOOK CLEARS THE PEGS. 3) DO EXERCISES AS DESIRED. 4) WHEN FINISHED WITH THE SET, ROTATE THE BAR BACK AND SET ON PEGS. MAKE SURE THE BAR IS SECURE BEFORE LETTING GO. 5) IF YOU DO INLINCE PRESS EXERCISES, LIFT TOWARD THE BACK OF THE MACHINE OR PUT AT LEAST 90 LBS. ON THE WEIGHT HOLDERS TO AVOID A POSSIBLE TIPPING HAZARD.
T-SHIRT ORDER FORM DELTECH FITNESS T - SHIRT SIZES AVAILABLE ARE M-XXL. THE COLOR OF THE SHIRTS ARE WHITE. RED AND BLACK LOGO. ONLY $12.99 DELTECH FITNESS MUSCLE SHIRT SIZES AVAILABLE M-XXL THE COLOR AVAILABLE IS BLACK. RED AND WHITE LOGO. ONLY $12.99 SEND TO: DELTECH MANUFACTURING, INC. 3910 OAKLAWN DR. LOUISVILLE, KY. 40219 ALL ORDERS SHIPPED UPS GROUND. MAKE CHECK OR MONEY ORDER PAYABLE TO: DELTECH MANUFACTURING KENTUCKY RESIDENTS ADD 6% SALES TAX. ALLOW 3 WEEKS FOR DELIVERY.
