ASSEMBLY INSTRUCTIONS FOR THE DF832 PEC ATTACHMENT (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE (888) 258-0533
BOX CONTENTS A B C D ARM MOUNT QTY 1 FIXED PULLEY BRACKET QTY 1 SWIVEL PULLEY BRACKET QTY 2 SWIVEL PULLEY MOUNT BRACKET QTY 1 E F G H RIGHT HAND CAM QTY 1 LEFT HAND CAM QTY 1 FLOATING PULLEY BRACKET QTY 1 ARM PAD QTY 2 I J K L BACKREST PAD QTY 1 RIGHT HAND ARM QTY 1 LEFT HAND ARM QTY 1 CABLE QTY 1 DF832 INSTRUCTIONS QTY 1 DF832 HARDWARE QTY 1
HARDWARE M N O P SLEEVE QTY 2 ARM BUSHING QTY 4 2” SQUARE CAP QTY 4 4-1/2” PULLEY QTY 4 Q R S T M12 x 190MM BOLT QTY 2 M10 x 76MM BOLT QTY 4 M10 x 50MM BOLT QTY 4 M10 x 70MM BOLT QTY 2 U V W X M8 x 25MM BOLT QTY 2 M12 WASHERS QTY 4 M10 WASHERS QTY 2 M8 WASHERS QTY 2 Y Z AA BB M19 LOCK NUT QTY 2 M12 LOCK NUT QTY 2 M10 LOCK NUT QTY 8 M8 LOCKNUT QTY 2 (888) 258-0533 FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY *NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLE
ARM & PULLEY MOUNT INSTALLATION W D AA R W A FRONT OF MACHINE TOOLS REQUIRED: WRENCHES OR METRIC SOCKET SET ASSEMBLE THE ARM MOUNT (A) AND THE SWIVEL PULLEY MOUNT BRACKET (D) TO THE FRONT SUPPORT OF THE LAT MACHINE USING THE M10 x 75MM BOLTS (R), M10 FLAT WASHERS (W) AND M10 LOCK NUTS (AA) NOTE: THE NUTS USED ON THIS PRODUCT ARE LOCK NUTS SO YOU MUST USE A WRENCH TO TIGHTEN THE BOLT. THE BOLT MUST GO THRU THE PLASTIC INSERT IN THE NUT.
CAM & ARM PAD ASSEMBLY E F O K J H H INSTALL THE ROLLER PADS (H) ON THE ARMS (K,J). (NOTE IT MAY HELP TO TAKE A DAMP CLOTH AND WET THE ARM BEFORE SLIDING THE PAD ON THE ARM) NEXT INSTALL THE CAMS (E,F) ON THE ARMS. THERE IS A LEFT HAND AND A RIGHT HAND SIDE SO YOU WILL NEED TO LOOK AT THE DIAGRAM TO ENSURE CORRECT INSTALLATION NOW INSERT THE 2” CAPS (O) INTO THE WEIGHT ARMS. NOTE: THE WEIGHT ARMS HAVE BEEN TESTED AT THE FACTORY BEFORE SHIPPING TO ENSURE THEY WILL FIT INSIDE THE CAM.
ARM INSTALLLATION Y Y N N A INSERT THE ARM BUSHINGS (N) INTO THE ARM MOUNT (A).
SWIVEL PULLEY ASSEMBLY C AA W W S ASSEMBLE THE 4 ½” PULLEY (P) INTO THE SWIVEL PULLEY BRACKET (C) USING THE M10 x 50MM BOLT (S), M10 WASHERS (W), AND M10 LOCKNUT (AA). REPEAT FOR OTHER SWIVEL PULLEY ASSEMBLY. P M Q Q SWIVEL PULLEY INSTALLATION V V INSTALL THE SWIVEL PULLEY ASSEMBLIES TO THE MOUNT BRACKET USING THE M12 x 190MM BOLTS (Q), M12 WASHERS (V), AND M12 LOCKNUTS (Z).
FIXED PULLEY ASSEMBLY AA P W W S INSTALL THE 4 ½” PULLEY(P) INTO THE FIXED PULLEY BRACKET (B) USING THE M10 x 50MM BOLT (S) M10 WASHERS (W), AND M10 LOCK NUT (AA). B FIXED PULLEY & BACKREST INSTALLATION T W T X ASSEMBLE THE BACKREST PAD (I) TO THE FRONT SUPPORT OF THE LAT MACHINE USING THE M8 x 70 BOLTS(T) AND THE M8 FLAT WASHERS (X).
FLOATING PULLEY ASSEMBLY P AA W W S G ASSEMBLE THE 4 ½” PULLEY (P) TO THE FLOATING PULLEY BRACKET (G) USING THE M10 x 50MM BOLT (S), M10 WASHERS (W) AND M10 NUT (AA).
CABLE INSTALLATION SWIVEL PULLEY ASSEMBLIES FIGURE A FLOATING PULLEY ASSEMBLY ATTACH THE PEC CABLE TO THE CAM ON THE LEFT SIDE USING THE M8 x 25MM BOLT, M8 WASHERS , AND M8 LOCKNUT. (SEE FIGURE A) NOTE: THERE ARE ADJUSTMENT HOLES ON EACH CAM TO COMPENSATE FOR CABLE STRETCH AFTER THE MACHINE IS USED FOR A WHILE. RUN THE CABLE THROUGH THE LEFT SIDE SWIVEL PULLEY, DOWN THROUGH THE FLOATING PULLEY, UP THROUGH THE RIGHT SIDE SWIVEL PULLEY AND ATTACH TO RIGHT CAM. TIGHTEN THE BOLTS ON THE SWIVEL PULLEYS.
CABLE INSTALLATION RE-ATTACH LOWER CABLE HERE DISCONNECT LOWER CABLE FROM HERE DISCONNECT THE LOWER CABLE ALREADY ATTACHED TO THE MACHINE AND RUN IT THOUGH THE FIXED PULLEY AND RE-ATTACH IT TO THE RING AT THE BOTTOM OF THE FLOATING PULLEY ASSEMBLY. MAKE SURE ALL YOUR BOLTS ARE TIGHT BEFORE USE. CHECK THEM PERIODICALLY TO MAKE SURE THEY ALWAYS STAY TIGHT.
SAFETY NOTICE WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS FOLLOWING THESE SIMPLE RULES: 1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU. 2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
T-SHIRT ORDER FORM DELTECH FITNESS T - SHIRT SIZES AVAILABLE ARE M-XXL. THE COLOR OF THE SHIRTS ARE WHITE. RED AND BLACK LOGO. ONLY $12.99 DELTECH FITNESS MUSCLE SHIRT SIZES AVAILABLE M-XXL THE COLOR AVAILABLE IS BLACK. RED AND WHITE LOGO. ONLY $12.99 SEND TO: DELTECH MANUFACTURING, INC. 3910 OAKLAWN DR. LOUISVILLE, KY. 40219 ALL ORDERS SHIPPED UPS GROUND. MAKE CHECK OR MONEY ORDER PAYABLE TO: DELTECH MANUFACTURING KENTUCKY RESIDENTS ADD 6% SALES TAX. ALLOW 3 WEEKS FOR DELIVERY.
Squat Rev Curl Finish Finish Finish Start Start Start Shrug Row Low Row Finish Finish Finish Start Start Start Side Row Tri Pull Curl Finish Finish Finish NOT ALL EXERCISES ARE RECOMMENDED FOR EVERYONE PLEASE CONSULT A PHYSICIAN BEFORE STARTING ANY EXERCISE PROGRAM Start Start Start Lat Pull Exercise Chart for the DF906
