LCD REAR PROJECTION TELEVISION 50V500A 50VX500 60VX500 OPERATING GUIDE IMPORTANT SAFETY INSTRUCTIONS FIRST TIME USE 2-3 4-22 Page 7 updated 01/09/04 THE REMOTE CONTROL 23-44 ON-SCREEN DISPLAY 45-69 USEFUL INFORMATION INDEX 70-81 Video Audio Aspect Chan. Manager Locks Setup Move SEL Sel As an ENERGY STAR® Partner, Hitachi, Ltd. has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. http://www.pureglare.com.
IMPORTANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR HITACHI LCD REAR PROJECTION TELEVISION Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions. Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you.
IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment 15. Televisions are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury. 16. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer. 17.
ACCESSORIES Check to make sure you have the following accessories before disposing of the packing material. SIMPLE REMOTE CONTROL REMOTE CONTROL BATTERIES (“AA”) IR MOUSE CABLE FIRST TIME USE POWER VCR TV CBL STB SOURCE WIZARD CD DVD PVR AMP 1 2 3 4 5 6 A/V NET 7 CH + 8 SELECT VOL - VOL + VIDEO EX U FAV CH MUTE INFO ASPECT A/V NET C.C. ANT 9 0 SLEEP IT MEN CH MENU 3.
HOW TO SET UP YOUR NEW HITACHI LCD REAR PTV ANTENNA LOCATION Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.
HOOK-UP CABLES AND CONNECTORS FIRST TIME USE Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors.
FRONT PANEL CONTROLS PUSH PUSH INPUT 5 PHOTO MC S-VIDEO MENU/SELECT button VIDEO L/MONO R AUDIO VOL- VOL+ CH- CH+ INPUT MENU EXIT SELECT This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode. INPUT/EXIT button Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source.
FRONT PANEL CONTROLS FIRST TIME USE IR RECEIVER/LEARNING AV NET sensor The screen area acts as the IR receiver (remote sensor) and the LEARNING AV NET sensor of the TV. When using the remote control, point it towards the screen for best response. POWER button Press this button to turn the TV on or off. POWER light This light is on during normal operation. Light Blinking Slowly (2 seconds): television lamp is cooling down. It takes 12-15 seconds to warm up and about 2 minutes to cool down. NOTES: 1.
FRONT PANEL JACKS AND CONNECTORS The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples: INPUT 5 S-VIDEO NOTE: VIDEO L/MONO R AUDIO S-VIDEO VIDEO L/MONO R AUDIO 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture may be abnormal. 2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable. 3.
REAR PANEL JACKS FIRST TIME USE ANT A DVI-HDTV TO CONVERTER PR PB R (MONO)/L PR PB R (MONO)/L R (MONO)/L VIDEO S-VIDEO R (MONO)/L VIDEO S-VIDEO Y INPUT 1 AUDIO ANT B INPUT 2 Y/VIDEO AUDIO AUDIO TO HI-FI CENTER IN INPUT 3 INPUT 4 IR BLASTER L R L VIDEO S-VIDEO MONITOR OUT AUDIO R Antenna Input/Output ANT A- A 75-Ohm RF antenna or CATV (Cable TV) input. ANT A can be displayed as a main picture or sub-picture.
REAR PANEL JACKS Component: Y-PBPR Inputs NOTES: 1. Do not connect composite VIDEO and S-VIDEO to Input 3, 4 or 5 at the same time. S-VIDEO has priority over VIDEO input. 2. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TV’s PB input and the components R-Y output to the TV’s PR input. 3. Your component outputs may be labeled Y-CBCR.
REAR PANEL CONNECTIONS FIRST TIME USE TYPICAL FULL-FEATURE SETUP CONNECT TO IR BLASTER (Provided) IR Sensor D-VHS Outside antenna or cable TV coaxial cable DIGITAL OUTPUT L R OUTPUT DVD Player 2-Way signal splitter Y HDTV Set-Top Box OUTPUT PB/CB PR/CR L R PB PR OUTPUT Y L R ANT A VCR #1 DVI-HDTV TO CONVERTER ANT IN PR PB R (MONO)/L PR PB R (MONO)/L R (MONO)/L VIDEO S-VIDEO R (MONO)/L VIDEO S-VIDEO Y INPUT 1 AUDIO ANT B INPUT 2 Y/VIDEO AUDIO AUDIO TO HI-FI CENTER IN
TIPS ON REAR PANEL CONNECTIONS S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature. • If your device has only one audio output (mono sound), connect it to the left audio jack on the television. • Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.
CONNECTING EXTERNAL AUDIO DEVICES To control the audio level of an external audio amplifier with the TV remote control, connect the system as shown below.
CONNECTING EXTERNAL VIDEO DEVICES The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs. Before Operating External Video Source The input mode is changed every time the VID1~VID5 button is pressed as shown below.
CONNECTING EXTERNAL VIDEO DEVICES FIRST TIME USE CONNECTING A STEREO SOURCE TO INPUT2~INPUT5 1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO DEVICES CONNECTING AN S-VIDEO SOURCE TO INPUT 3, 4 AND 5 1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO DEVICES FIRST TIME USE CONNECTING A COMPONENT SOURCE WITH DVI-HDTV CAPABILITY TO INPUT 1 1. Connect the DVI connection cable from the output of the HDTV set top box or DVD player to the DVI-HDTV input as shown on the TV set below. 2. Connect the cable from the AUDIO OUT R of the HDTV set top box or DVD player to the INPUT (AUDIO/R) jack. 3. Connect the cable from the AUDIO OUT L of the HDTV set top box or DVD player to the INPUT (AUDIO/L) jack. 4.
CONNECTING EXTERNAL VIDEO DEVICES CONNECTING A COMPONENT SOURCE TO INPUT 1 OR 2: Y-PBPR. 1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below. Connect the cable from the CB/PB OUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB) jack. 3. Connect the cable from the CR/PR OUT or R-Y OUT of the laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack. 4.
FIRST TIME USE CONNECTING AV NETWORK Your Hitachi LCD TV is equipped with an AV Network feature. This feature helps to control your external Audio/Video equipment (VCR, Set Top Box, DVD, etc.). Once this is setup, it allows your IR Mouse connector to control your equipment using your Hitachi TV Remote Control. You can use your Hitachi remote control to control the Audio/Video equipment command without the equipment’s remote control. The television rear panel has 2 IR BLASTER jacks.
AV NETWORK SETUP WIZARD 5. Follow the steps below to setup your AV network (See page 22 for AV Network Codes). There are six steps in the setup procedure (DVD setup example below). HITACHI AV NET SET UP MENU THUMB STICK MORE DVD Device Code Video Input ---(Enter code “9999” to uninstall) No Connection Audio Input No Connection Cable Box Photo MC Transmission Test BACK Move INFO Move Device Setting 0 POWER OK PLAY EXIT CH UP Input 0-9 9 Enter the device (equipment) code listed on page 22.
FIRST TIME USE AUDIO/VIDEO NETWORK (AV NET) CODES VCR BRAND . . . . . . . . . . . . . . . . . . . . . . . . . . . CODE Admiral . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0048, 0209 Adventura . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0000 Aiko . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0278 Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0000, 0037 Akai . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THE REMOTE CONTROL In addition to controlling all the functions on your HITACHI LCD Rear PTV, the new remote control is designed to operate different types of VCRs, CATV (Cable TV) converters, set-top-box, satellite receiver, DVD players, and other audio equipment with one touch. Basic operation keys are grouped together in one area. If you prefer to use the AV Network feature, switching remote control modes is not needed.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV VCR TV CBL CD DVD PVR THE REMOTE CONTROL AMP 1 2 3 4 5 6 7 8 9 0 ANT INFO ASPECT A/V NET C.C.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV PVR (Personal Video Recorder) button When pressed, this button will blink to indicate the remote is in PVR mode (see page 41). CD and AMP buttons When pressed, each of these buttons will blink to indicate the remote is in Audio mode (see page 42). CHANNEL selector buttons CHANNEL selector buttons are used to select channels, lock access code, etc. Enter one, two, or three numbers to select channels.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV A/V NET button Press this button to access the Audio/Video network (AV Net) menu. The AV Net allows the user to control external components with the LCD Rear PTV’s remote control. When you press the AV NET button, the following window will pop up within the Display Monitor screen. The window will disappear after 30 seconds if you don’t press any buttons. The AV Net Setup Wizard will automatically start upon the very first use (see page 20-22).
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV Photo MC The Photo MC feature is useful for viewing digital still pictures from your digital camera using a memory card and displaying them on the TV screen. Insert Photo MC (memory card) to be viewed to a PC Card adapter. Insert the loaded PC Card adapter to the Photo MC slot of the control panel in the front of the TV. LED Light and OSD Indicator Press THUMBSTICK to view the digital photos in THUMBNAIL view.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV SLIDESHOW Select this menu item to start a slideshow of the Photos in the memory card. Time interval selections can be set from 5, 10 and 30 seconds. Jump 1/10 2/10 Slideshow Rotate 3/10 4/10 5/10 6/10 7/10 8/10 9/10 10/10 THUMB STICK 1/10 2/10 3/10 Jump Slideshow Start Rotate Interval 5 sec 4/10 5/10 6/10 8/10 9/10 10/10 SELECT 7/10 Slideshow THUMB STICK SELECT 5 seconds.. etc.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV B POWER VCR CH CH MENU THUMB STICK TV/VCR PV Recorder POWER CH CH MENU PV Recorder 1 2 3 TV/VCR AV Receiver 4 5 6 INFO 7 8 9 GUIDE LAST CH 0 - MORE VCR INFO GUIDE MORE.. Move INFO MORE..
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV AV NET LEARNING WIZARD This function of the AV NET makes it more expandable because it allows the user to use equipment that is not supported by the pre-code library, listed on page 22. For example, after programming your equipment to the AV NET and the soft keys do not work, the user just has to follow the steps below. The AV NET Learning Wizard will transfer any remote button IR code of your equipment to the soft keys of your AV NET.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV ASPECT button Press this button to quickly change the picture format ASPECT ratio. Depending on the input signal, the picture format ratio allows you to adjust the images through the following options. 4:3 Standard Use this aspect mode to display conventional (4:3) images. Side panels (gray areas) are placed to the left and right of the image to preserve the original aspect ratio of the source.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV VIDEO button Press this button to directly access the VIDEO adjustment menu. VIDEO EX IT Contrast Next/Prev 100% Change Value SEL Return MENU button The MENU button will start the On-Screen Display. EXIT button When in MENU mode, this button will exit all On-Screen Displays. THE REMOTE CONTROL THUMB STICK/SELECT button All the On-Screen Display features can be set or adjusted by using the THUMB STICK, except for numeric entries.
HOW TO USE THE REMOTE TO CONTROL YOUR LCD REAR PTV 1 LAST CHANNEL (LAST CH) button Use this button to select between the last two channels viewed (Good for watching two sporting events, etc.). 3:32 PM Ant A 39 Stereo R 3:32 PM Ant A 10 Stereo R LAST CH PICTURE-IN-PICTURE buttons See separate section on pages 34~36 for a description. 23 SURF button Press the SURF button to automatically scan all active channel numbers (those set in memory) and display them as PIP subpictures.
PICTURE-IN-PICTURE (PIP) Your HITACHI LCD Rear PTV incorporates dual tuner technology designed for improved viewing enjoyment. This dual tuner feature allows you to view antenna inputs on both the main picture and sub-picture simultaneously, with separate tuning control for each. ANT A input can be viewed as both the main picture and the sub-picture simultaneously. Ant B can only be viewed as a main picture. To select between main picture and PIP sub-picture tuning, press the SWAP button on the remote.
PICTURE-IN-PICTURE (PIP) SPLIT MODE PICTURE-IN-PICTURE Split Mode PIP displays the main picture and sub-picture evenly on the screen. Sub Picture Main Picture SWAP button (with PIP ON) Press this button to toggle between the Main and Sub picture which is highlighted with a green border around the picture. Picture sound and channel can be controlled when it is highlighted. SWAP SPLIT The SWAP button will only operate in POP/PIP/SPLIT PIP mode.
PICTURE-IN-PICTURE (PIP) FREEZE button (With PIP ON) If you wish to freeze the sub-picture, press the FREEZE button. This is convenient when trying to write down the address for a mail order company, recording statistics for a sporting event, etc. To return the picture to motion, press the FREEZE button again. NOTE: When PIP is on, the FREEZE function will only operate when POP/PIP/SPLIT mode is chosen.
USING THE REMOTE TO CONTROL VCR FUNCTIONS Operating the precoded function for your VCR. This remote is designed to operate different types of VCRs. You must first program the remote to match the remote system of your VCR (refer to page 44 for pre-codes). 1. Turn ON your VCR. 2. Aim the remote control at the front of your VCR. 3. Press and release the VCR button to switch to VCR pre-coded mode. 4.
USING THE REMOTE TO CONTROL CABLE BOX FUNCTIONS Operating the precoded function for your cable box. THE REMOTE CONTROL This remote is designed to operate different types of cable boxes. You must first program the remote to match the remote system of your cable box (refer to page 44). 1. Turn ON your cable box. 2. Aim the remote control at the front of your cable box. 3. Press and release the Cable (CBL) button to switch to Cable pre-coded mode. 4.
USING THE REMOTE TO CONTROL SET-TOP-BOX/SATELLITE RECEIVER FUNCTIONS Operating the precoded function for your set-top-box/satellite receiver. This remote is designed to operate different types of set-top-box/satellite systems. You must first program the remote to match the remote system of your set-top-box/satellite systems (refer to page 44). 1. Turn ON your set-top-box/satellite systems. 2. Aim the remote control at the front of your set-top-box/satellite systems. 3.
USING THE REMOTE TO CONTROL DVD FUNCTIONS Operating the precoded function for your DVD player. THE REMOTE CONTROL This remote is designed to operate different types of DVD players. You must first program the remote to match the remote system of your DVD player (refer to page 44 for pre-codes). 1. Turn ON your DVD player. 2. Aim the remote control at the front of your DVD player. 3. Press and release the DVD button to switch to DVD pre-coded mode. 4.
USING THE REMOTE TO CONTROL PVR FUNCTIONS Operating the precoded function for your PVR (Personal Video Recorder). This remote is designed to operate different types of PVRs. You must first program the remote to match the remote system of your PVR (refer to page 44 for pre-codes). 1. Turn ON your PVR. 2. Aim the remote control at the front of your PVR. 3. Press and release the PVR button to switch to PVR pre-coded mode. 4.
USING YOUR REMOTE TO CONTROL ADDITIONAL AUDIO EQUIPMENT Operating the precoded function for your Audio component. THE REMOTE CONTROL This remote is designed to operate different types of Audio component. You must first program the remote to match the remote system of your Audio component (refer to page 44 for pre-codes). 1. Turn ON your Audio component you wish to control with the Remote. 2. Aim the remote control at the front of your Audio component. 3.
THE SIMPLE REMOTE CONTROL HITACHI has provided a second remote control for your convenience. The Simple Remote Control has the basic features that are most often used. A/V NET CH + VOL + SELECT VOL - FAV CH MUTE CH MENU ANT EXIT/ASPECT POWER POWER button CH+ ( ), CH- ( ) Press the CH+ ( ) up or CH- ( ) down buttons to select desired channel or to navigate the on screen display features when in A/V NET mode.
THE REMOTE CONTROL VCR, CABLE, SATELLITE, DVD and AUDIO CODES FOR REMOTE CONTROL VCR BRAND. . . . . . . . . . . . . . . . . CODE Adventura . . . . . . . . . . . . . . . . . . . . . . 01 Aiko. . . . . . . . . . . . . . . . . . . . . . . . . . . 09 Aiwa . . . . . . . . . . . . . . . . . . . . . . . . . . 01 Akai . . . . . . . . . . . . . . . . . . . . . 02, 47, 48 American High. . . . . . . . . . . . . . . . . . . 23 Asha . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Audiovox . . . . . . . . . . . .
ON-SCREEN DISPLAY (OSD) 1. Press MENU on the remote control to display the different features on your HITACHI LCD TV. 2. Press the THUMB STICK to highlight a different feature. 3. Press EXIT on the remote control to quickly exit from a menu. 4. Press A/V Net on the remote control to access the AV Net menu to control external components. 5. Press THUMB STICK or to access Favorite Channels menu. A/V Net NU ME EX IT SELECT This part of the screen shows which selections are available.
ON-SCREEN DISPLAY (OSD) Picture Mode Video Select between the two picture modes; Day and Night. Adjust contrast. Adjust brightness. Adjust color. Adjust tint. Adjust sharpness. Set this to High for less intense color with more blue, set to Medium for natural color, set to Standard for standard colors or Black/White for more reddish color. Adjust shadow detail in dark screens. Choose Automatic Contrast settings. Choose the Reset Video settings.
VIDEO Select Video to adjust picture settings and improve picture quality. You can customize each of the Video Inputs to your preference to increase viewing performance and pleasure depending upon the video program being viewed. If RESET is selected, only the selected mode will reset to initial conditions. Video Picture Mode Use this function to choose from automatic picture settings to optimize your TV’s performance. Video Audio Aspect Chan.
VIDEO Video Video Contrast Aspect Chan. Manager THUMB STICK Locks ME Move Day Night 100% Brightness 50% Color 50% Tint Setup NU ANT A/B Picture Mode Audio SELECT SEL Sel Sharpness 50% Color Temperature High Black Enhancement High Contrast Mode Dynamic Reset Video Settings Move SEL Select Use the THUMB STICK or to highlight the function to be adjusted. Press down on THUMB STICK to select the function settings. Press the THUMB STICK or to adjust the function.
VIDEO This function allows you to Reset the Video Menu Settings of the present input and return it to the Day or Night conditions depending on the selected Video mode.
VIDEO Use this function to adjust the percentage of Red, Green and Color according to the user’s preference. Use Tint to adjust flesh tones so they appear natural. Color Decoding Video Video ANT A/B Color Decoding Color Management Color Decoding Auto Color Off Noise Reduction Low Auto Movie Mode Off Move SEL RGB THUMB STICK Select R G Red 50% Green 50% Color 50% B Tint Reset Move SEL Return Use THUMBSTICK to highlight function. Press down to select from 4 menu items.
AUDIO Select Audio to adjust the TV to your preference and to improve the sound quality. Audio Audio Video Audio Aspect THUMB STICK Locks Setup NU ME Move SELECT SEL 45% Bass 50% Balance Chan. Manager THUMB STICK Treble Sel L Sound Enhancement Off Audio Source Stereo Internal Speakers On Auto Noise Cancel On Perfect Volume On On Loudness Move R Change Value SEL Return Press THUMB STICK , , to select menu item. Press THUMB STICK or to adjust the function.
AUDIO Sound Enhancement The following surround settings will reproduce the “live” sound you would hear in concert halls, sports stadiums, movie theaters, etc. with only two channels. Audio Video Audio Aspect THUMB STICK NU ME THUMB STICK Locks Setup SELECT SEL 45% Bass 50% Balance Chan.
ASPECT MODE Aspect Mode Use this function to select the Picture Format Aspect Ratio. Auto Aspect Automatically adjust the Aspect Ratio depending on the input signal to fill the screen. Press THUMB STICK , , to select menu item. Press down on THUMBSTICK to select. A “ ” in the box indicates that the feature is ON. NOTES: 1. The Auto Aspect function is recommended on an input signal with VIDEO ID. 2. The Auto Aspect function is best used on component video, S-Video, and 480i component signals. 3.
CHANNEL MANAGER Chan. Manager Select Antenna if you are using an indoor or outdoor antenna. Select Cable if you have cable TV. Chan. Manager Chan. Manager Ant. A Ant. A Ant. B Move SEL Select THUMB STICK Channel Source Antenna SELECT Auto Channel Scan Cable(1) Cable(2) Start Channel List Move SEL Return THUMB STICK Chan. Manager Ant.
CHANNEL MANAGER This feature will automatically store active TV channels in Auto Channel Scan. This will allow you to skip unused channels when using CHANNEL UP ( ) or DOWN ( ). Auto Channel Scan Chan. Manager Chan. Manager Ant. A Ant. A Channel Source Antenna Cable(1) Auto Channel Scan Cable(2) THUMB STICK SEL Cable(1) Auto Channel Scan Start Channel List Move Channel Source Antenna Cable(2) Start Channel List Select Move SEL Select THUMB STICK SELECT Chan. Manager Ant.
CHANNEL MANAGER Channel List This function allows you to review which channels are labeled (Ch ID), which have been added to Channel Memory (Scan), and which are protected by Lock. Chan. Manager Chan. Manager Channel List Ant.
CHANNEL MANAGER This section contains advanced features which will make TV viewing easier and more enjoyable. Use this feature to give up to 20 channels a name when Antenna signal source is selected and up to 60 channels a name when Cable TV signal source is selected. Channel ID Chan. Manager Chan. Manager Ant. A Ant.
LOCKS This function will block out the picture and sound of the selected channel or video input. It can also be used to keep the TV from being viewed for a scheduled time period that you set. Locks The code to enter the Locks feature is a four digit secret code number. The factory preset code is 0000. Use the number buttons to select access code. Video Audio Aspect Please Enter Access Code THUMB STICK Chan.
LOCKS Movie Ratings Use Movie Ratings to block from showing any movie you feel might have inappropriate content. Locks Locks Movie Ratings Change Access Code Engage Lock THUMB STICK TV Time Lock THUMB STICK Movie Ratings Status Not Rated: G: PG: TV Ratings NU SELECT ME PG-13: Canadian Ratings (Eng) R: Canadian Ratings (Frn) Move SEL Select NC-17: X: Move SEL Return Use THUMB STICK or to select the Movie Rating category that you want to block.
LOCKS TV Ratings Use TV Ratings to block from showing any programs or movies you feel might have inappropriate content. Locks Locks TV Ratings Change Access Code Sub Category Engage Lock THUMB STICK TV Time Lock THUMB STICK Movie Ratings D L S V FV TV-Y: TV-Y7: TV Ratings NU Status SELECT ME Canadian Ratings (Eng) TV-G: Canadian Ratings (Frn) TV-PG: Move SEL Select TV-14: TV-MA: Move SEL Return Use THUMB STICK or to highlight the category that you want to block.
LOCKS Canadian Ratings (Eng) Use Canadian Ratings (Eng) to block any type of movie and television program in Canada that you feel might be inappropriate in its content.
LOCKS Canadian Ratings (Frn) Use Canadian Ratings (Frn) to block Canadian French programs according to various program ratings that you feel might be inappropriate in its content.
SETUP Setup Select Setup when setting your TV up for the first time. Use the THUMB STICK or on the remote to highlight the function desired. Video Setup Menu Preference Audio Screen Saver Aspect THUMB STICK THUMB STICK Chan. Manager Locks NU ME SELECT Setup Move Set The Clock Set The Inputs Set The Color System Set Black Side Panel Sel SEL Set Event Timer Set Closed Captions Move SEL Select Use THUMB STICK or to select the sub-menu of your choice.
SETUP Set The Menu Background This function allows you to choose from two menu backgrounds. Setup Menu Preference Set The Language English French THUMB STICK Spanish Set The Menu Background Shaded Solid Move SEL Select Use THUMB STICK , to highlight Set The Menu Background (shaded or solid), and press down on THUMB STICK to select setting. Press EXIT to quit menu or THUMB STICK to return to previous menu.
SETUP The time must be adjusted before you can use the “Set Event Timer” or “TV Time Out” features.
SETUP Set The Inputs Use this feature to give a name to any of the five video inputs.
SETUP Set The Color System This function allows you to automatically change tint and color coordinates for DTV programs. HDTV - High Definition Television - Use for High Vision Signal Y-PBPR from HDTV Set-Top Box. SDTV/DVD - Standard Definition Television or DVD (Digital Versatile Disc Player) Y-CBCR. NOTES: 1. If Color System is set improperly (does not match actual input signal), the color and tint of the main picture will be abnormal. 2.
SETUP Set Event Timer This function will automatically turn the Projection TV on and off, one time only, every day, or once a week. This Event Timer is only for Ant A/Ant B. If the clock is not set, you can not use this function and the screen below will appear in Ant A and Ant B. The message on the screen will disappear after 3 seconds, then the screen automatically goes to the clock setup mode (see page 65). Please Set Clock First.
SETUP Closed Captions are the dialogue, narration, and/or sound effects of a television program or home video which are displayed on the TV screen. Your local TV program guide denotes these programs as or .
LAMP REPLACEMENT LAMP REPLACEMENT Lamp Life The lamp life may vary based on usage of the LCD Rear PTV. Turning on and off frequently may shorten the life of the lamp. Lamp Replacement After extended use, if the TV picture turns dark, the color looks unusual or LAMP INDICATOR light turns on, then it is time to replace the lamp with a new lamp. WARNING: The lamp gets very hot! The lamp may explode if improperly handled. To avoid injury, please observe the following precautions.
LAMP REPLACEMENT 1. 120V FRONT COVER PUSH POWER NOTE: 2. THE LAMP IS VERY HOT AND MAY CAUSE FIRE OR SEVERE BURNS. WAIT AT LEAST 30~45 MINUTES TO ALLOW THE LAMP TO COOL BEFORE PROCEEDING WITH LAMP REMOVAL. Remove the front cover from the TV set. This is held by a snap on. Pull the front cover outwards until the quick snap on disengages. LAMP COMPARTMENT PULL FRONT COVER NOTE: PUSH The lamp in this product contains Mercury. Dispose of properly in accordance with applicable environmental laws.
LAMP REPLACEMENT Remove the screw securing the lamp cover with a Phillips head screw driver as shown. Remove the lamp cover. LAMP REPLACEMENT 3. SCREW LAMP COVER PHILLIP HEAD SCREW DRIVER NOTE: 4. THE LAMP IS VERY HOT AND MAY CAUSE FIRE OR SEVERE BURNS. WAIT AT LEAST 30~45 MINUTES TO ALLOW THE LAMP TO COOL BEFORE PROCEEDING WITH LAMP REMOVAL. Remove the two screws that hold the lamp in place. Remove the lamp unit by holding the lamp handle, then pulling outwards.
LAMP REPLACEMENT 6. SCREW LAMP COVER PHILLIP HEAD SCREW DRIVER NOTE: 7. IF POWER IS CONNECTED BEFORE THE LAMP COVER IS INSTALLED, THE POWER WILL BE OFF AND THE LAMP INDICATOR WILL FLASH (SEE PAGE 8 ). Install the front cover as shown below. Put the front cover back in and align the snap on quick connect then push inwards holding the left and right side of the front cover until you hear a snap. Push the other snap on gently to make a good fit. PUSH FRONT COVER 8.
CARE OF YOUR HITACHI TELEVISION AND YOUR REMOTE CONTROL DO Dust the screen and cabinet with a soft cloth. Clean the screen with a soft cloth moistened in warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Place your Television away from extreme heat, humidity, and extremely dusty places. Remove the plug from the wall outlet if your Television will not be used for a long period of time, for instances, when you go on vacation.
RECEPTION PROBLEMS • IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. • GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception.
TV i ure No Picture, no sound Try SYMPTOMS ss rd cor is p rec lug t ge wit d in an c he oth d ''O er N" cha Ch nn eck el ( an sta ten t ion na Ch tr o eck con ub ne an le) ctio ten ns na Ch (ba for eck ck bro ou of T ken tsid V) Ch lea ea eck d-i nte n nn for wir a loc e al i Ad nte jus tC r fe ren on t r ce a Ad st c jus on tB tr o rig l htn Ad ess jus con tC tr o olo l rc Ad on jus tr o tT l int con Ad tr o jus l tV olu me Re con pla tr o ce l La mp CH TR ECK Y T TH HE ES Be SE E I sur AD T
USEFUL INFO Features: • Superfine Picture Quality 1280 Line Horizontal Resolution • Remote (Controls many VCR brands, cable boxes, satellite boxes, and other audio equipment.) • Extra Simple Remote for easy basic operations. • New Easy-to-Use (3-Language) On-Screen Menu • New AV Network Infra-Red (IR) System Control up to 4 components with one remote. (2 IR Mouse cables included.
USEFUL INFO To locate an authorized HITACHI service facility in the continental U.S.A. and Canada, DIAL TOLL FREE 7 days a week, 24 hours a day (1-800-448-2244) Hitachi America, LTD. Home Electronics Division Hitachi has made every effort to assure you hours of trouble free operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto Rico.
USEFUL INFO Hitachi Canada, LTD. Digital Media Division Should you have any questions regarding warranty, service, operation, or technical assistance, please contact: In Canada: 1-800-HITACHI (1-800-448-2244) Monday - Friday EST 9:00am - 7:00pm Saturday EST 9:00am - 5:00pm Look for your French Manual on the outside of the box. If the manual is missing, call 1-800-HITACHI (1-800-448-2244) for a copy.
INDEX INDEX Clock Time, 65 A Date, 65 Closed Captions Analog Captions, 69 Color System, 67 Color Temperature, 48 Color, 48 Contrast, 48 Accessories, 4 Antennas (Connecting), 5, 6 Aspect Ratio, 31 Audio (Sound Enhancement) SRS, 52 BBE, 52 Audio Settings, 51 - 52 D Audio Source, 51 DVI-HDTV, 11, 12, 18 Audio/Video Network (A/V Net), 21 - 22, 26, 29-30 Auto Color, 50 Auto Noise Cancel, 51 E AV Net Event Timer ANT A/B, 68 AV Net Code, 22 AV Net Setup, 20~21 AV Net Usage, 26~30 B Balance, 51 Bass, 5
INDEX L Picture-in-Picture (PIP), 34 - 36 Lamp Picture-outside-Picture (POP), 36 Lamp Indicator, 8 Lamp Replacement, 70-73 Language R Menu Language, 63 Locks Remote Control Functions, 23 - 42 Programming Codes, 37 - 44 Installing Batteries, 4 Change Access Code, 58 Channel Lock, 58 Input Lock, 58 Front Panel Lock, 58 TV Time Lock, 58 Movie Ratings, 59 S TV Ratings, 60 TV Ratings (Canadian - English), 61 TV Ratings (Canadian - French), 62 Loudness, 51 Sharpness, 48 Simple Remote Control, 43 Sound
NOTES 82 http://www.pureglare.com.
NOTES 83 http://www.pureglare.com.
QR58982 http://www.pureglare.com.