AV SURROUND RECEIVER AVR-2106 OPERATING INSTRUCTIONS
ENGLISH SAFETY INSTRUCTIONS 2 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
ENGLISH 2 System setup menu page page page page page 8~11 52 52, 53 53 53 page page page page page 48 49 49, 50 50 50 page page page page page page page 42 42 42 43 43 44 44 page 45 page 45 page page page page 46 46 46 46 page 47 page 47
ENGLISH Getting Started Advanced Operation Getting Started Thank you for choosing the DENON AVR-2106 A/V Surround Receiver. This remarkable component has been engineered to provide superb surround sound listening with home theater sources, such as DVD, as well as providing outstanding high fidelity reproduction of your favorite music sources.
ENGLISH Getting Started Getting Started Accessories Cautions on installation Check that the following parts are included in addition to the main unit: q Operating instructions ............................1 w Warranty .................................................1 e Service station list ..................................1 r Power supply cord..................................1 t Remote control unit (RC-1015) ...............
ENGLISH Getting Started Getting Started Inserting the batteries Part names and functions q Remove the remote control unit’s rear cover. w Set two R6P/AA batteries in the battery compartment in the indicated direction. e Put the rear cover back on. Notes on batteries: • Replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the unit. (The included batteries are only for verifying operation.
ENGLISH Getting Started Remote control unit Easy Setup and Operation For details on the functions of these parts, refer to the pages given in parentheses ( ). Indicator ···············(34, 36) ZONE2 buttons····(36, 39) SURROUND MODE buttons·················(19, 27) Power buttons ································(8, 34) • This section contains the basic steps necessary to configure the AVR-2106 according to your listening room environment and the source equipment and loudspeakers you are using.
ENGLISH Easy Setup and Operation Easy Setup and Operation Speaker system layout Speaker connections • Connect the speaker terminals with the speakers making sure that like polarities are matched (< with <, > with >). Mismatching of polarities will result in weak central sound, unclear orientation of the various instruments, and the stereo image being impaired.
ENGLISH Easy Setup and Operation Easy Setup and Operation 2 Connections 2 Bi-Amp connections When making connections, also refer to the operating instructions of the other components. Certain loudspeakers are equipped with two sets of input terminals, for bi-amplification. The AVR2106 Power Amp Assign. mode allows you to power bi-amp-capable speakers with two amplifier channels ( page 47). Be sure to consult the owner’s manual of your bi-amp-capable speakers for further information before proceeding.
ENGLISH Easy Setup and Operation Easy Setup and Operation • For best picture quality (especially with progressive DVD and other high definition sources), choose the component video connection to your monitor TV. S-Video and composite video outputs are also provided if your TV does not have component video inputs. Connecting a DVD player and monitor TV • To connect the video output from the DVD player to the AVR-2106, you only need to choose one connection type.
ENGLISH Easy Setup and Operation Easy Setup and Operation ON/SOURCE POWER SPEAKER A MODE 1 ENTER SETUP CURSOR ON/STANDBY SETUP MIC Auto Setup / Room EQ Connecting a microphone 1 Connect the microphone for Auto Setup to the SETUP MIC jack on the front panel of the unit. q: This sets the speaker connection, polarity, and bass reproduction ability. w: This sets the delay time from each speaker corresponding to the listening position. e: This sets the volume that is output from each speaker.
ENGLISH Easy Setup and Operation Starting Auto Setup 1 Press the SETUP button. • The “System Setup” menu appears. Easy Setup and Operation When “S. Back” is selected, the test tone during Auto Setup will be output from the surround back speaker. When “ZONE2” is selected, change the setting to “ZONE2”. The test tone during Auto Setup is set so that it will not be output to ZONE2 (Another room). When “Bi-Amp” is selected, change the setting to “BiAmp”.
ENGLISH Easy Setup and Operation Easy Setup and Operation Check of the measurement results About error messages • These error screens may be displayed when performing Auto Setup measurement and the automatic measurements can not be completed because of the speaker arrangement, measurement environment, or other factors. Please check the following matters, reset the pertinent items, and measure again. • When there is too much noise in the room, the speakers may not be detected properly.
ENGLISH Easy Setup and Operation 4 Press the CURSOR D or H button to select from the following three items based on the measurement results, then press the CURSOR F button. Connecting Other Sources Cable indications The hookup diagrams on the subsequent pages assume the use of the following optional connection cables (not supplied). Store: Store the checked measurement values. All parameters are stored. Retry: Perform the measurement again. Measurement is repeated.
ENGLISH Connecting Other Sources Connecting Other Sources The video conversion function On screen display signals With the AVR-2106, the Video signal and the S-Video signal which were inputted are mutually converted. And also the Video signal and the S-Video signal which were inputted are converted into a higher quality. The flow of the video signals.
ENGLISH Connecting Other Sources Connecting Other Sources Connecting a TV/DBS tuner Connecting the external inputs (EXT. IN) terminals • For best picture quality choose the component video connection to your TV or DBS tuner. S-Video and composite video inputs are also provided if your TV or DBS tuner does not have component video outputs. • To connect the digital audio output from the TV or DBS tuner, you can choose from either the coaxial or optical connections.
ENGLISH Connecting Other Sources Connecting Other Sources Connecting a DVD recorder Connecting a VCR • For best picture quality choose the component video connection to your VCR. S-Video and composite video outputs are also provided. If you choose to use the component video connection, it needs to be assigned. For more information about Component Input Assignment ( page 43). • You can connect a second video recorder to the VCR-2 terminals.
ENGLISH Connecting Other Sources Connecting Other Sources Connecting a tape deck Connecting a CD recorder or MD recorder If you wish to perform analog dubbing from a digital source, such as a CD or MD recorder to an analog recorder such as a tape deck, you will need to connect the analog inputs and outputs as shown below, in addition to the digital audio connections.
ENGLISH Connecting Other Sources Connecting Other Sources Connecting the antenna terminals Connecting the XM terminal • AVR-2106 is the XM Ready® receiver. You can receive XM Satellite Radio® by connecting to the XM Connect-and-Play™ (sold separately) and subscribing the XM service. • Plug the XM Connect-and-Play antenna into XM terminal on the rear panel. • Position the XM Connect-and-Play antenna near a south-facing window to receive the best signal. For details, see “XM Satellite Radio” ( page 32).
ENGLISH Connecting Other Sources Connecting Other Sources Connecting the RS-232C terminal Connecting the MULTI ZONE terminals For instructions on operations using the MULTI ZONE functions ( These terminals are used for an external controller. Perform the following operation before using an external controller connected to the RS-232C terminal: 1. Press the ON/STANDBY button on the main unit and set the unit to the operating mode. 2. Perform the operation to turn off the power from the external control.
ENGLISH Connecting Other Sources Connecting Other Sources ZONE2 speaker out connections Connecting the pre-out terminals • When the power amplifier is assigned to the ZONE2 output channel at “Power Amp Assign.” in the “System Setup” menu, the surround back speaker terminals can be used as the ZONE2 speaker out terminals ( page 38). • The connections diagram below is an example for when the surround back speaker is assigned to the ZONE2 stereo 2 channel.
ENGLISH Basic Operation Playback using the external input (EXT. IN) terminals Basic Operation The signals being input to the external decoder input terminals are played without passing through the surround circuitry. Playback MASTER VOLUME INPUT MODE ANALOG FUNCTION DIMMER STATUS SURROUND MODE FUNCTION VIDEO SELECT MAIN EXT.
ENGLISH Basic Operation Basic Operation Listening over headphones Connect the headphones to the PHONES jack. • The pre-out output (including the speaker output) is automatically turned off when headphones are connected. Checking the currently playing program source 2 On screen display Press the ON SCREEN button. NOTE: • To prevent hearing loss, do not raise the volume level excessively when using headphones.
ENGLISH Basic Operation Basic Operation 2 Input mode display • In the AUTO mode STEREO/DIRECT/PURE DIRECT Depending on the input signal. STANDARD DIRECT/ PURE DIRECT STEREO • In the DIGITAL PCM mode ENTER • In the DIGITAL DTS mode STANDARD SELECT SURROUND PARAMETER CURSOR SURROUND PARAMETER • In the ANALOG mode Surround 2 Input signal display • The AVR-2106 is equipped with 2-channel playback modes exclusively for music. • Select the mode to suit your tastes.
ENGLISH Basic Operation Basic Operation Dolby Pro Logic IIx (Pro Logic II) mode • To play in the PLIIx mode, set “S. BackSp” at the “Speaker Configuration” setting to “1sp” or “2sp”. • To play in the PLIIx mode, set “Surround Back” at the “Power Amp Assign.” setting. 1 When the “SB CH OUT” parameter is set to “OFF”. (Set “S. BACK” at system setup to “NONE”.) Display (Pro Logic II Cinema mode) Press the STANDARD button to select the Dolby Pro Logic IIx mode.
ENGLISH Basic Operation Basic Operation 2 Surround parameters w STANDARD FUNCTION INPUT MODE SURROUND MODE FUNCTION ENTER SURROUND PARAMETER CURSOR STANDARD SELECT SURROUND PARAMETER SURROUND BACK INPUT MODE DTS NEO:6 mode 1 Press the STANDARD button to select the DTS NEO:6 mode. The mode switches as shown below each time the button is pressed. DOLBY PLIIx 2 3 4 5 DTS NEO:6 Play a program source. Press the SURROUND PARAMETER button to select the surround parameter mode.
ENGLISH Basic Operation Basic Operation Dolby Digital mode and DTS surround (only with digital input) 1 Select an input source set to digital (COAXIAL/ OPTICAL) ( page 42). Example: DVD (Main unit) 2 3 7 8 Turn the SELECT knob, and press the CURSOR F or G button to adjust the parameter settings. Press the ENTER button to finish the surround parameter mode. Press the INPUT MODE button to set the input mode to “AUTO” or “DTS”.
ENGLISH Basic Operation Basic Operation 2 Dialog normalization FUNCTION INPUT MODE STATUS The dialog normalization function is activated automatically when playing Dolby Digital program sources. Dialog normalization is a basic function of Dolby Digital which automatically normalizes the dialog level (standard level) of the signals which are recorded at different levels for different program sources, such as DVD, DTV and other future formats that will use Dolby Digital.
ENGLISH Basic Operation Basic Operation Adjusting the audio delay • When watching a DVD or other video source, the picture on the monitor may seem delayed with respect to the sound. In this case, adjust the audio delay to delay the sound and synchronize it with the picture. • The audio delay setting is stored separately for each input source. • This adjustment can be performed with the system setup ( page 45) or from the remote control unit, as described below.
ENGLISH Basic Operation Basic Operation 2 Operating the surround mode and the surround parameters from the main unit‘s panel SURROUND MODE SURROUND MODE 1 ENTER SURROUND PARAMETER CURSOR Turn the SELECT knob to select the surround mode.
ENGLISH Basic Operation Basic Operation Room EQ setting 2 Operate the Room EQ from the remote control unit 1 2 Operate the Room EQ from the main unit 2 Surround parameters r 1 ROOM SIZE: This sets the size of the sound field. There are five settings: “small”, “med.s” (medium-small), “medium”, “med.l” (medium-large) and “large”. “small” recreates a small sound field, “large” a large sound field. • The surround parameter screen appears. EFFECT LEVEL: This sets the strength of the surround effect.
ENGLISH Basic Operation Basic Operation TONE CONTROL SELECT CH SELECT CURSOR G CURSOR F TONE DEFEAT Tone control setting Channel Level 2 Adjusting the sound quality (tone) The tone control function will not work in the PURE DIRECT or DIRECT mode. 1 Press the TONE CONTROL button. The tone switches as follows each time the TONE CONTROL button is pressed. BASS 2 You can adjust the channel level either according to the playback sources or to suit your taste, as described below.
ENGLISH Basic Operation FUNCTION ON/STANDBY Basic Operation BAND POWER Auto tuning PRESET • TUNER TUNING MODE BAND TUNING Listening to the radio Auto preset memory • This unit is equipped with a function for automatically searching for FM broadcast stations and storing them in the preset memory. • The “Auto tuner preset” operation can also be performed at “System setup” ( page 44). Hold the PRESET • button and press the POWER switch on the main unit.
ENGLISH Basic Operation Basic Operation Checking the preset stations FUNCTION BAND PRESET STATUS TUNING TUNER BAND MEMORY PRESET MODE The preset (broadcast) stations can be checked on the on screen display. Press the ON SCREEN button repeatedly until the “Tuner Preset Stations” screen appears on the OSD. SHIFT ON SCREEN ON/STANDBY SHIFT POWER TUNING Manual tuning 1 2 3 Set the input source to “TUNER”. Watching the display, press the BAND button to select the desired band (AM or FM).
ENGLISH Basic Operation XM Satellite Radio 2 Introducing XM Satellite Radio There’s a world of audio listening pleasure beyond AM and FM. XM Satellite Radio. Select from over 150 channels of music, news, sports, comedy, talk, and entertainment. Coast-to-coast coverage. Digital quality sound. With all music channels 100% commercial free. Questions?: Visit www.xmradio.com. 2 How to subscribe Listeners can subscribe by visiting XM on the Web at www.xmradio.
ENGLISH Advanced Operation Advanced Operation OFF ON SOURCE 3. Tuner system buttons 1. CD player (CD), CD recorder and MD recorder (CDR/MD) system buttons NUMBER MODE 1 MODE 2 Remote control unit Operating DENON audio components 6, 7 2 1 8, 9 3 DISC SKIP + : : : : : : Manual search (forward and reverse) Stop Play Auto search (cue) Pause Switch discs (for CD changers only) 2. Tape deck (TAPE) system buttons 1 Set the MODE 1 switch to “AUDIO”.
ENGLISH Advanced Operation Advanced Operation Preset memory • DENON and other makes of components can be operated by setting the preset memory. • This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown in the list of preset codes ( End of this manual). • Operation is not possible for some models. 1 Set the MODE 1 switch to “AUDIO” or “VIDEO”.
ENGLISH Advanced Operation 2. Video disc player (VDP) system buttons ON/SOURCE : Power on/standby 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 8, 9 : Auto search (cue) 3 : Pause 0 ~ 9, +10 : Number Advanced Operation 3. Video deck (VCR) system buttons ON/SOURCE : Power on/standby 6, 7 : Manual search (forward and reverse) 2 : Stop 1 : Play 3 : Pause Channel +, – : Channel up/down 35 ENGLISH 4.
ENGLISH Advanced Operation Advanced Operation 5. Monitor TV (TV) system buttons MAIN ON ZONE2 OFF NUMBER MODE 1 MODE 2 Punch through “Punch Through” is a function allowing you to operate the PLAY, STOP, MANUAL SEARCH and AUTO SEARCH buttons on CD, TAPE, CDR/MD, DVD/VDP or VCR components when in the DBS/CABLE or TV mode. By default, nothing is set.
ENGLISH Advanced Operation Advanced Operation Multi zone music entertainment system • When the outputs of the ZONE2 OUT terminals are wired and connected to integrated amplifiers installed in other rooms, different sources can be played in rooms other than the MAIN ZONE in which this unit and the playback devices are installed. (Refer to ZONE2 on the diagram below.) • ZONE2 speaker out and pre-out can be used when “ZONE2” is selected at “Power Amp Assign.” in the “System Setup” menu.
ENGLISH Advanced Operation Advanced Operation 2 When using the SURR.BACK/ZONE2 amplifier as the ZONE2 • The SPEAKER OUT, LINE OUT and PRE OUT terminals can be used simultaneously in ZONE2. • To use the ZONE2, turn on the ZONE2 button. • The output of the ZONE2 SPEAKER OUT terminals can be adjusted with the remote control unit’s ZONE2 VOLUME button. [System configuration and connections example] Using this unit’s internal amplifier as the ZONE2. MAIN ZONE 5.
ENGLISH Advanced Operation Advanced Operation ZONE2 OFF FUNCTION ZONE2/REC SELECT ZONE2 ON FUNCTION CHANNEL MODE 1 POWER ZONE2 SPEAKER VOLUME Outputting a program source to amplifier, etc., in a different room (ZONE2 mode) 1 MODE 2 Press the ZONE2/REC SELECT button to display the “ZONE2 SOURCE” on the display. Remote control unit operations during multi-source playback (selecting the source) 1 Set the MODE 1 switch to the “AUDIO”. 2 Set the MODE 2 switch to the “ZONE2”.
ENGLISH Advanced Operation Advanced Operation Other functions Playing one source while recording another (REC OUT mode) 1 Press the ZONE2/REC SELECT button to display the “RECOUT SOURCE” on the display. The display switches as follows each time the button is pressed. ZONE2 2 3 REC Turn the FUNCTION knob to select the source you want to output appears on the display. Set the recording mode. For operating instructions, refer to the manual of the component on which you want to record.
ENGLISH Advanced Setup – Part 1 On screen display and front display Advanced Setup – Part 1 The AVR-2106 is equipped with an intuitive and easy-to-understand on screen display, and is equipped with an alphanumeric front panel display that can also be used to check and adjust settings. We recommend that you use the on screen display when you make system adjustments. Some representative front display and on screen display examples are shown below.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Input Setup Setting the Input Function Level Setting the Digital In Assign. This setting assigns the digital input terminals of the AVR-2106 for the different input sources. 1 Press the CURSOR D or H button to select “Input Setup” at the “System Setup” menu, then press the ENTER button. • The “Input Setup” menu appears.
ENGLISH Advanced Setup – Part 1 Setting the Function Rename The names of the input sources displayed on the front display and the on screen display can be changed. The names or brands of the devices connected to the input sources can be input. 1 Press the CURSOR D or H button to select “Function Rename” at the “Input Setup” menu, then press the ENTER button. Advanced Setup – Part 1 4 Repeat step 3 to complete input of the input source name.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Setting the Video Input Mode Select the input signal to be output to the composite S-Video and component monitor output terminals using the video conversion function. 1 Press the CURSOR D or H button to select “Video Input Mode” at the “Input Setup” menu, then press the ENTER button. • The “Video Input Mode” screen appears.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Advanced playback Setting the Auto Surround Mode Setting the Audio Delay • When watching a DVD or other video source, the picture on the monitor may seem delayed with respect to the sound. In this case, adjust the audio delay to delay the sound and synchronize it with the picture. • The audio delay setting is stored separately for each input source. 1 • The audio delay setting does not apply when playing in the EXT.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Option Setup Setting the Trigger Out Setup • Two 12 V DC Trigger Outputs on the rear panel can be used to control other devices with compatible trigger inputs, such as motorized screens, motorized screen masking, motorized drapes, and other trigger-controlled devices. • Set the DC output supplied from the trigger out terminals for the various input sources to “ON” or “OFF”.
ENGLISH Advanced Setup – Part 1 Advanced Setup – Part 1 Setting the Power Amp Assign. Setting the Setup Lock Make this setting to switch the power amplifier for the surround back channel to ZONE2 or Bi-Amp. Power Amp Assign. Surround back ZONE2 Bi-Amp 1 SPEAKER OUT MAIN ZONE ZONE2 7.1ch system – 5.1ch system 2ch system – 5.1ch system PRE-OUT S.BACK/ZONE Surround back ZONE2 – The system setup settings can be locked so that they cannot be changed easily.
ENGLISH Advanced Setup – Part 2 2 Parameters Advanced Setup – Part 2 This Speaker Setup section describes the procedures to make speaker settings manually (without using the Auto Setup function), as well as to make manual changes to settings that have already been made by the Auto Setup function. ENTER CURSOR The composition of the signals output to each channel and the frequency response are adjusted automatically according to the combination of speakers actually being used.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 Setting the Delay Time Input the distance between the listening position and each speaker to set the delay time for the surround playback. Preparations: Measure the distances between the listening position and the speakers. FL Center FR Subwoofer 4 Press the ENTER button to enter the setting. • The “Speaker Setup” menu appears.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 Setting the Crossover Frequency • To cancel the settings, press the CURSOR H button to select “Level Clear” on the “Channel Level” screen, then make the settings again. • When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer’s own volume control. • When you adjust the channel levels while in the system setup channel level mode, the channel level adjustments made will affect all surround modes.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 2 Assignment of low frequency signal range 2 Subwoofer Mode The only signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency signal range of channels set to “Small” in the setup menu. The low frequency signal range of channels set to “Large” are produced from those channels.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 Others Setup Setting the Manual EQ Setup Adjust the tone of the various speakers except subwoofer speaker while listening to the sound (music). 1 4 2 Press the CURSOR D or H button to select the frequency. Press the CURSOR F or G button to select “All” or “Assign”. All: The Equalizer to all surround mode is set as once. Assign: The Equalizer to each surround mode is to set individually.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 Check the EQ parameter • The Equalizer setting of “Normal”, “Flat” and “Front” can be selected after performing the Auto Setup. • When the speaker set as “None” with the Auto Setup is change to on manually, the equalizer of “Normal”, “Front” and “Flat” cannot be used. • The Equalizer setting can be selected by SURROUND PARAMETER button. • When headphone is connected, the Room EQ cannot be used.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 System setup items and default values (set upon shipment from the factory) 1. Auto Setup / Room EQ Auto Setup / Room EQ 1 Auto Setup Power Amp Assign. Set this to switch the surround back channel’s power amplifier for ZONE2 or BiAmp use . Default setting Page SURROUND BACK 8~11 2 Manual EQ Setup This parameter is for optimizing the Room EQ with which the audio signals are produced from the speakers.
ENGLISH Advanced Setup – Part 2 Advanced Setup – Part 2 3. Input Setup Input Setup 1 2 CD DVD / VDP TV / DBS VCR-1 CDR / TAPE Digital Inputs COAX1 OPT1 OPT2 COAX2 OPT3 Digital In Assign. This assigns the digital input terminals for the different input sources. Ext In SW Level Sets the Ext. In Subwoofer terminal playback level. 42 Subwoofer = +15 dB Input 3 Function Level The playback level can be corrected individually for the PHONO different input sources.
ENGLISH Troubleshooting Symptom Cause This unit does not operate properly when remote control unit is used. • Batteries dead. • Remote control unit too far from this unit. • Obstacle between this unit and remote control unit. • Different button is being pressed. • < and > ends of batteries inserted in reverse. Troubleshooting If a problem should arise, first check the following. 1. Are the connections correct? 2. Have you operated the receiver according to the operating instructions? 3.
ENGLISH Additional Information Surround back speakers Additional Information • Other types of audio: These signals are designed to recreate a 360° sound field using three to five speakers. Optimum surround sound for different sources There are currently various types of multi-channel signals (signals or formats with more than two channels).
ENGLISH Additional Information With this set, speaker(s) for 1 or 2 channels are required to achieve a 6.1-channel system (DTS-ES, etc.). Adding these speakers, however, increases the surround effect not only with sources recorded in 6.1 channels but also with conventional 2- to 5.1-channel sources. Furthermore, all the DENON original surround modes ( page 26) are compatible with 7.1-channel playback, so you can enjoy 7.1-channel sound with any signal source.
ENGLISH Additional Information Additional Information [2] When not using surround back speakers Front speakers Center speaker Monitor Subwoofer 60° 120° Surround speakers [ As seen from above ] Surround speaker Surround The AVR-2106 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.
ENGLISH Additional Information • Whereas with conventional Dolby Pro Logic the surround channel playback frequency band was limited, Dolby Pro Logic II offers a wider band range (20 Hz to 20 kHz or greater). In addition, the surround channels were monaural (the surround left and right channels were the same) with previous Dolby Pro Logic, but with Dolby Pro Logic II they are played as stereo signals.
ENGLISH Additional Information [3] DTS-ES Extended Surround™ DTS-ES Extended Surround is a new multi-channel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility with the conventional DTS Digital Surround format, DTS-ES Extended Surround greatly improves the 360degree surround impression and space expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since 1999. In addition to the 5.
ENGLISH Additional Information Additional Information Surround modes and parameters Signals and adjustability in the different modes When playing Dolby Digital and DTS signals Channel output Mode FRONT L/R CENTER SURROUND L/R SURROUND BACK L/R SUBWOOFER C C C C C C C C C C C C C C C E E B B B B B B B B B B B B E E E B B B B B B B B B B B B E E E E B B B B B B B B B B B E B B B B B B B B B B B B B B B DIRECT/PURE DIRECT STEREO EXTERNAL INPUT DOLBY PRO LOGIC II DOLBY PRO LOGIC IIx DTS NEO:6 DOLBY
ENGLISH Specifications 2 Video section Specifications • Standard video terminals Input / output level and impedance: 1 Vp-p, 75 Ω/ohms Frequency response: 5 Hz ~ 10 MHz — +1, –3 dB • S-Video terminals Input / output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω/ohms C (color) signal — 0.286 Vp-p, 75 Ω/ohms Frequency response: 5 Hz ~ 10 MHz — +1, –3 dB • Color component video terminal Input / output level and impedance: Y (brightness) signal — 1 Vp-p, 75 Ω/ohms PB/CB (blue) signal — 0.
ENGLISH 2 List of preset codes / Liste de codes préréglés DVD Audio Dynamic 005, 085 Denon 014, *[111] Audiovox 088 Aiwa 009 Beaumark 087 Jensen Hitachi 010 Broksonic 086, 093 JVC JVC 006, 011 Calix 088 Konka 012, 013 Candle 006, 087, 088, 089, 090 Magnavox 005 Canon 049, 057 Mitsubishi 004 Capehart 025, 055, 056, 071 Kodak 088 Panasonic 014 Carver 015 Lloyd 009, 094 Philips 005, 015, 016, 017 CCE 095 LXI 088 Pioneer 003, 008 Citizen 006, 007, 087, 088, 08
ENGLISH Optonica 021 Sylvania 009, 015, 016, 017, 041, 049, 094 Bauer 155 Panasonic 024, 049, 064, 066, 067, 068, 069, 107 Symphonic 009, 094 Belcor 047 Perdio 009 Tandy 009 Bell & Howell 045, 118 Pentax 009, 013, 023, 058, 090 Tashiko 009, 088 Bradford 061 Philco 015, 016, 049 Tatung 004, 026, 030 Brockwood 003, 047 Philips 015, 021, 042, 049, 105 Teac 004, 009, 026, 094 Candle Pilot 088 Technics 024, 049 Pioneer 005, 013, 029, 036, 037, 038, 045, 085 Teknika 009,
ENGLISH Futuretech 004 Minutz 066 SBR 015 GE 020, 036, 037, 040, 044, 058, 066, 088, Mitsubishi 001, 016, 039, 048, 056, 057, 058, 065, Schneider 015 081, 082, 083, 105 Scott 062 000, 015, 029, 031, 039, 048, 051, 056, Montgomery Ward 011, 020, 144, 145, 146 Sears 008, 014, 021, 022, 023, 024, 025, 040, 057, 067, 068, 069, 116 Motorola 121, 147 Grundy 062 MTC 031, 034, 039, 048, 095 Hitachi 029, 031, 051, 052, 070, 111, 112, 113, NAD 008, 075, 076, 128 119, 120, 125, 147 Golds
ENGLISH CABLE DBS (SATELLITE) Emerson 004, 005, 006, 007 003, 008, 009, 010 ABC 006, *[007], 008, 009 Alphastar 054 Fisher Archer 010, 011 Chaparral 035, 036 JVC 018, 019 011, 012, 013, 014, 017 Century 011 Dishnet 053 Kenwood Citizen 011 Drake 037, 038 Magnavox 006, 015, 035 Colour Voice 012, 013 Echostar Dish 062, 066 Marantz 016, 028, 035 Comtronic 014 GE 048, 055, 056 MCS 016, 024 Eastern 015 General Instruments 039, 040, 041 Onkyo 025, 027 Garrard 011 Grun
ENGLISH Magnavox 002 Marantz 002 Onkyo 016, 018 Optimus 007, 008 Panasonic 012 Philips 002 Pioneer 007, 008, 009 Sony 013, 014, 015 Technics 012 Victor 004 Wards 007 Yamaha 010, 011 *[ ] : Preset codes set upon shipment from the factory. *[ ] : Les codes préréglés diffèrent en fonctiom des livraison de l’usine. DVD preset codes Codes préréglés DVD B Model No.
TOKYO, JAPAN www.denon.com Denon Brand Company, D&M Holdings Inc.
