Operation Manual


Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
Setting items Setting contents
Bass Setting
Settings for subwoofer and
LFE signal range playback.
Subwoofer Mode : Select low range signals to be reproduced by
subwoofer.
LFE : The low range signal of the channel set to “Small” speaker size is
added to the LFE signal output from the subwoofer.
LFE+Main : The low range signal of all channels is added to the LFE
signal output from the subwoofer.
This can be set when “Speaker Configuration” – “Subwoofer” (vpage
34) is set to “Yes”.
Play music or a movie source and select the mode offering the strongest
bass.
Select “LFE+Main” if you want the bass signals to always be produced
from the subwoofer.
•
•
•
•
•
LPF for LFE : Set LFE signal playback range.
80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz•
Distance
Set distance from listening
position to speakers.
Measure beforehand the
distance from the listening
position to each speaker.
Unit : Set the unit of distance.
Feet
Meters
•
•
Step : Set the minimum variable width of the distance.
1ft / 0.1ft
0.1m / 0.01m
•
•
Front L / Front R / Center / Subwoofer / Surround L / Surround R /
S. Back L
z
/ S. Back R
z
/ Front Height L / Front Height R : Select the
speaker.
z: When the “Speaker Configuration” – “Surround Back” setting
(vpage 34) is set to “1spkr”, “S. Back” is displayed.
0.0ft ~ 60.0ft / 0.00m ~ 18.00m : Set the distance.
Speakers set to “None” in “Speaker Configuration” (vpage 34) are
not displayed.
The speakers that can be selected differ depending on the “Amp Assign”
(vpage 34) and “Speaker Configuration” (vpage 34) settings.
Default settings :
Front / Center / Subwoofer / Front Height : 12.0 ft (3.60 m)
Surround / Surround Back : 10.0 ft (3.00 m)
Set the difference in the distance between the speakers to less than 20
feet (6.0 meters).
•
•
•
•
•
Default : Reset all distance settings to factory default.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
When you select “Default” and press ENTER, the “Default Setting?”
prompt is displayed. Select either “Yes” or “No”, and press ENTER.
•
•
Making Detailed Settings (Manual Setup)
Setting
Setting items Setting contents
Channel Level
Set the volume of the test
tone to be the same when it
is output from each speaker.
Test Tone Start : Output test tone.
Front L / Front Height L / Center / Front Height R / Front R / Surround
R / S. Back R
z
/ S. Back L
z
/ Surround L / Subwoofer : Select the
speaker.
z
: When the “Speaker Configuration” – “Surround Back” setting
(vpage 34) is set to “1spkr”, “S. Back” is displayed.
–12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
Speakers set to “None” in the “Speaker Configuration” (vpage 34)
settings are not displayed.
When o is pressed while the subwoofer volume is set to “–12 dB”, the
“Subwoofer” setting switches to “OFF”.
When a headphones jack is inserted in the PHONES terminal of the AVR-
3310CI, the “Channel Level” is not displayed.
You can also press [CHANNEL LEVEL] to set (vpage 79 “Adjust the
Volume of the Different Speakers“).
•
•
•
•
•
•
Default : Reset all channel level settings to factory default.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
•
•
Crossover Frequency
Outputs at below set
frequency, each speaker’s
bass signal output from
the subwoofer. Set this
according to the low
frequency reproduction
capabilities of the speakers
you are using.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Advanced : Specify crossover frequency for each speaker.
Front / Center / Surround / Surround Back / Front Height : Select the
speaker.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz /150Hz / 200Hz /
250Hz : Set the crossover frequency.
Can be set when the “Speaker Configuration” – “Subwoofer” (vpage
34) setting is “Yes”, or when you have a speaker that is set to “Small”.
Always set the crossover frequency to “80 Hz”. When using small
speakers, however, we recommend setting the crossover frequency to
a higher frequency.
For speakers set to “Small”, sound below the crossover frequency is cut
from the sound output. The cut bass sound is output from the subwoofer
or front speakers.
The speakers that can be set when “Advanced” is selected differ
according to the “Subwoofer Mode” setting (vpage 35).
When “LFE” is selected, speakers set to “Small” at “Speaker
Configuration” can be set. If the speakers are set to “Large”, “Full
Band” is displayed and the setting cannot be made.
If set to “LFE+Main”, this setting can be made regardless of the
speaker size.
•
•
•
•
•
•
•
•
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu