Operation Manual


Getting Started Connections Playback Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
See overleaf
Making Detailed Settings (Manual Setup)
Main remote control
operation buttons
:Displaying the menu
Cancel the menu
:Moves the cursor
(Up/Down/Left/Right)
:Confirm the setting :Return to previous menu
Setting items Setting contents
2ch Direct/Stereo
(Continued)
SW Mode : Select low range signal to be reproduced by subwoofer.
LFE : When the “2ch Direct/Stereo” – “Front” (vpage 37) setting is
set to “Large”, the LFE signal alone is output from the subwoofer. Also,
when the “2ch Direct/Stereo” – “Front” setting is set to “Small”, the
front channel low range signal is added to the LFE signal output from
the subwoofer.
LFE+Main : The front channel low range signal is added to the LFE signal
output from the subwoofer.
This can be set when “2ch Direct/Stereo” – “Subwoofer” (vpage
37) is set to “Yes”.
•
•
Crossover : Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer.
40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
This can be set when “2ch Direct/Stereo” – “Subwoofer” (vpage 37)
is set to “Yes”.
If the “2ch Direct/Stereo” – “Front” setting is “Large” and the “SW
Mode” setting is “LFE”, “Full Band” is displayed and the setting cannot
be made.
•
•
•
Distance FL / Distance FR : Select the speaker.
0.00m ~ 18.00m (3.60m) / 0.0ft ~ 60.0ft (12.0ft) : Set the distance to
the speaker.
Set so that the difference between the front left speaker and front
right speaker distances is 6.0 m (20.0 ft) or less.
•
Level FL / Level FR : Select the speaker.
–12.0dB ~ +12.0dB (0dB) : Adjust the level of each channel.•
Auto Surround Mode
Make setting for memorizing
surround mode setting for
each input signal type.
ON : Memorize settings. Automatically play with the last used surround
mode.
OFF : Do not memorize settings. Surround mode does not change
according to input signal
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals listed
below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r Multi-channel signals other than Dolby Digital and DTS (PCM, DSD,
etc.)
When playing in the PURE DIRECT, the surround mode does not change
even if the input signal is changed.
•
•
Setting items Setting contents
EQ Customize
Set so that unused equalizer
settings are not displayed
when [MULTEQ XT] is
pressed.
Equalizer settings for which
“Not Used” is set with the
Quick Select function cannot
be stored and called out.
Audyssey Byp. L/R : Set when not using the “Audyssey Byp L/R”
equalizer.
Used : Use.
Not Used : Do not use.
Set so that the “Audyssey Byp. L/R” settings can be made when the
Audyssey Auto Setup procedure is performed.
•
•
Audyssey Flat : Set when not using the “Audyssey Flat” equalizer.
Used : Use.
Not Used : Do not use.
Set so that the “Audyssey Flat” settings can be made when the
Audyssey Auto Setup procedure is performed.
•
•
Manual : Set when not using the “Manual” equalizer.
Used : Use.
Not Used : Do not use.
•
•
Make network settings.
Setting items Setting contents
Network Connecting
Make settings for wired
LAN.
1. Connect the LAN cable (vpage 22 “Connecting to a Home Network
(LAN)”).
2. Turn on the AVR-4310 (vpage 23 “Turning the Power On”).
AVR-4310 performs automatic network setup due to the DHCP
function.
When connecting to a network that has no DHCP function, perform the
setting in step 3.
3. Set the IP address at the “Network Connecting”.
NETWORK CONNECTING
Exit
Detail
192.168.100.33
Set IP address and proxy manually
ONDHCP
IP Address
Enter
NETWORK CONNECTING
Proxy
Exit
192 . 168 . 100 . 033
Set IP address manually
OFFDHCP
IP Address
255 . 255 . 255 . 000Subnet Mask
000 . 000 . 000 . 000Default Gateway
000 . 000 . 000 . 000Primary DNS
000 . 000 . 000 . 000Secondary DNS
RETURN
Cancel
q
w
r e
Making the Network Settings (Network Setup)
Default settings are underlined.
Settings