Operation Manual


Getting Started Connections Settings Remote ControlMulti-zone Information Troubleshooting Specifications
ENGLISH
When you make an HDMI connection with a TV or player compatible
with AVR-4310 and HDMI control functions, you can perform the
following operations by setting the HDMI control function of each
device.
When you want to listen to TV audio by AVR-4310, connect optical
digital or analog audio (vpage 15 “Connecting the Monitor“).
When using these functions set as follows: “HDMI Control” –
“Control” (vpage 37) set to “ON“.
•
•
NOTE
When “Control” is set to “ON”, it consumes more standby power.
The HDMI control function controls operations of a TV that is
compatible with the HDMI control function. Make sure that the TV
and HDMI are connected when you perform HDMI control.
When you power off AVR-4310, the HDMI control function does not
operate. Either power on or set to standby.
Some functions may not operate depending on the connected TV
or player. Check the owner’s manual of each device for details
beforehand.
When “Control” is set to “ON”, it is not possible to assign an HDMI
terminal to “TV” at “Input Assign” (vpage 47).
•
•
•
•
•
1
Turn the power on for all the equipment connected
by HDMI cable.
2
Set the HDMI control function for all equipment
connected by HDMI cable.
Set “HDMI Control” – “Control” (vpage 37) to “ON“.
Please consult the operating instructions for the connected
equipment to check the settings.
Carryout steps 1 and 2 should any of the equipment be plugged
out.
b
b
3
Switch the television input to the HDMI connected to
the AVR-4310.
4
Switch the AVR-4310 input to the HDMI input source
and check if the picture from the player is ok.
5
When you turn the TV’s power to standby, check
that the power of the AVR-4310 and player also goes
on standby.
If the HDMI control function does not operate properly, check the
following points.
Is the TV or player compatible with the HDMI control function?
Is the AVR-4310 properly set?
Is the “HDMI Control” – “Control” (vpage 37) set to “ON”?
Is the “Power Off Control” (vpage 37) set to “ON”?
Is the “Control Monitor” (vpage 37) set for the monitor output
connected to television?
Are the HDMI control function settings of all equipment correct?
•
•
•
•
•
•
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step’s 1 and 2.
“Input Assign” – “HDMI” (vpage 47) setting has changed.
“Monitor Out” (vpage 36) setting is changed.
There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
•
•
•
AVR-4310 power off can be linked to the TV power
off step.
When you set “Output audio from amp” in the TV audio output
setup operation, you can switch the amp power on.
You can switch audio output devices with a TV
operation.
You can adjust AVR-4310 volume in the TV volume
adjustment operation.
You can switch AVR-4310 input source through
linkage to TV input switching.
When playing the player, the AVR-4310 input function
switches to the function of that player.
n
n
n
n
n
HDMI Control Function
Convenient Functions
With this function, you can set the AVR-4310 so that the power is
automatically switched to standby after the set amount of time has
passed.
This is convenient for playing sources while going to sleep.
To cancel the sleep timer
Press [SLEEP] to set “OFF”.
The “ ” indicator on the display turns off.
n
The sleep timer setting is canceled if the AVR-4310’s power is set to
standby or turned off.
The sleep timer function can be set separately for the different zones
(vpage 85 “Sleep Timer Function”).
•
•
Press [SLEEP] and display the time you want to set.
The “ ” indicator on the display lights.
The time switches as shown below each time [SLEEP] is pressed.•
OFF 120 min 90 min
60 min30 min
Setting the Power to Standby After a
Certain Amount of Time
(Sleep Timer Function)
Playback