AV SURROUND RECEIVER AVR-788 Owner’s Manual Manuel de l’Utilisateur 1.AVR788E3_ENG_108.
ENGLISH FRANCAIS SAFETY INSTRUCTIONS n SAFETY PRECAUTIONS 1. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
FRANCAIS ENGLISH FCC INFORMATION (For US customers) n NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION 1. PRODUCT This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation. 2.
ENGLISH Contents Getting Started Accessories·······················································································2 Cautions on Handling······································································3 Cautions on Installation··································································3 About the Remote Control Unit·····················································3 Inserting the Batteries·····································································3 Operating Range
ENGLISH Other Information·································································56 ~ 64 List of preset codes············································ End of this manual Accessories Playback Specifications················································································ 68 Thank you for purchasing this DENON product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading them, be sure to keep them for future reference.
ENGLISH Getting Started Cautions on Handling About the Remote Control Unit • Before turning the power switch on Check once again that all connections are correct and that there are no problems with the connection cables. Connections • Power is supplied to some of the circuitry even when the unit is set to the standby mode. When traveling or leaving home for long periods of time, be sure to unplug the power cord from the power outlet.
ENGLISH For buttons not explained here, see the page indicated in parentheses ( ). Front Panel W2 W1 W0 Q9 Q8 Q7 Q6 Q5 Q4 W7 EXT.
ENGLISH Getting Started Rear Panel Q5 Q4 Q3 Q2 Q1 Q0 o i Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting q q Digital audio connectors (OPTICAL / COAXIAL)··························· (12, 13) w Analog audio connectors (AUDIO)············· (12) e EXT.
ENGLISH [ Front ] [ Rear ] Q1 w e w y e Multi-Zone u i o ENTER button········································ (18, 46) Q3 Q4 Q0 r Q1 Information y u Troubleshooting Q5 Q6 i o Remote Control Q2 t Playback t q q ZONE2 power buttons································ (55) w Source select buttons································· (41) e Tuner system buttons································· (42) r Test tone button (TEST)······························ (25) t Main zone power buttons (MAIN)·····
ENGLISH Getting Started Preparations Connections Connections Setup Connections for all compatible audio and video signal formats are described in these operating instructions. Please select the types of connections suited for the equipment you are connecting. With some types of connections, certain settings must be made on the AVR-788. For details, refer to the instructions for the respective connection items below.
ENGLISH GFlow of video signals inside the AVR-788H • When viewing component video signals via the AVR-788, the on-screen display appears when the MENU button or the remote control unit’s DISPLAY button is operated. • When only component video signals are input to the AVR-788, the characters of the on-screen display are not displayed over the picture. • The on-screen display signals are not outputted from the HDMI MONITOR OUT.
ENGLISH Getting Started Speaker Connections Speaker Connections Example: 5.1-channels (FRONT A+B) and ZONE2 use Speaker Installation Connections The illustration below shows a basic example of installation of the amplifier combined with 8 speakers and a monitor.
ENGLISH Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to the AVR-788, and be sure to interconnect the channels and polarities correctly. Insert the speaker cable’s core wire to the hilt into the speaker terminal. Remote Control Turn the speaker terminal counterclockwise to loosen it. Playback 2 3 4 Setup Peel off about 0.
ENGLISH Getting Started Connecting Equipment with HDMI connectors NOTE With HDMI connections, the video and audio signals can be transferred with a single cable. Connections DVD player Monitor )%.* 065 )%.* */ b The AVR-788 is equipped for HDMI version 1.3a. This version is compatible with other versions, allowing connection to all components equipped with an HDMI connector. b The AVR-788 is compatible with 30- and 36-bit Deep Color.
ENGLISH Connecting the Playback Components • Connect the cables to be used (vpage 8 “Video Conversion Function”). • With HDMI connections, the video and audio signals can be transferred with a single cable. • To output the audio signals to the monitor with HDMI connections, set menu “Manual Setup” – “HDMI Setup” to “TV” (vpage 25). 7*%&0 4 7*%&0 */ 7*%&0 */ )%.* */ • Connect the cables to be used. • With HDMI connections, the video and audio signals can be transferred with a single cable.
ENGLISH Getting Started CD Player iPod® Connect the cables to be used. CD player "6%*0 Connections 015*$"065 "6%*0 065 3 Setup Playback L R L R TV/CABLE Tuner Use a DENON Control Dock for iPod (ASD-1R, sold separately) to connect the iPod to the AVR-788. For instructions on the Control Dock for iPod settings, refer to the Control Dock for iPod’s operating instructions. Connect the cables to be used.
ENGLISH Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly. Make analog connections if you wish to record analog audio signals, or digital connections if you wish to record digital audio signals, depending on the types of connectors on the components being used. CD recorder / MD recorder / Tape deck Connect the cables to be used.
ENGLISH Getting Started Connections to Other Devices Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly.
ENGLISH An F-type FM antenna cable plug can be connected directly. Direction of broadcasting station Connections FM antenna AM loop antenna (supplied) Setup 75 Ω/ohms Coaxial cable Playback • The AVR-788 is an XM Ready® receiver. You can receive XM® Satellite Radio by connecting to the XM Mini-Tuner and Home Dock (includes home antenna, sold separately) and subscribing to the XM service. • Plug the XM Mini-Tuner and Home Dock into the XM connector on the rear panel.
ENGLISH Getting Started Connecting the Power Cord Multi-zone Wait until all connections have been completed before connecting the power cord. ZONE2 out Connections Connections If another pre-main (integrated) amplifier is connected, the ZONE2 out connectors can be used to play a different program source in ZONE2 at the same time (vpage 52 ~ 55).
ENGLISH Getting Started MENU ui Menu Operations ENTER, op [Front] Press MENU. 2 3 4 Press ui to select the item you want to set, then press ENTER. The menu is displayed. b To operate from the remote control unit, be sure to set the [MODE SELECTOR 1] to “AUDIO”. uiop ENTER [Selectable items] A B A+B Press ui again to select the item you want to set, then press ENTER.
ENGLISH Getting Started Examples of On-screen Display and Front Display Some typical examples are described below. GFront displayH GOn-screen displayH Connections Submenu title Auto Setup MENU 1.Auto Setup 2.Manual Setup 3.Input Setup 4.Parameter 5.Information Setup Playback Press o to execute Start• Remote Control Currently selected line Current setting Multi-Zone Digital :•OPT1– Press op to change the setting 1-1.
ENGLISH Getting Started Menu Map Auto Setup (vpage 21 ~ 23) MENU n Option • Room EQ • Direct Mode Setup n Parameter Check • Speaker Configuration Check • Distance Check • Channel Level Check • Crossover Frequency Check • EQ Check • Restore Connections n Start Menu • Step 1: Speaker Detection • Step 2: Measurement • Step 3: Calculation • Step 4: Check • Step 5: Store Setup 1.Auto Setup 2.Manual Setup 3.Input Setup 4.Parameter 5.
ENGLISH Getting Started Preparations 1 Auto Setup Connections Setup Playback Remote Control • Audyssey MultEQ® automatically measures the acoustical problems in the listening environment to create the best audio experience for your home theater. • It optimizes a large listening area where one or more listeners are seated. Measurements are performed by placing the calibrated microphone (DM-A405) successively at multiple positions throughout the listening area as shown in Example q.
ENGLISH Step 1 : Speaker Detection Optimize settings for speakers in use. F Menu screen F The settings are performed automatically. The auto setup measurement results are stored in the AVR-1908. NOTE Do not turn the power off while the settings are being stored. Measure 6 positions (main listening position and 5 other surrounding positions). Although it is allowable to measure less than 6 positions, it is recommended to measure 6 for best results.
ENGLISH Getting Started Error Messages s Option If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the auto setup procedure over again. Make various other settings.
ENGLISH s Subwoofer Setup Select surround speakers use and size. [Selectable items] Manual Setup Large Small Select low range signal to be reproduced by subwoofer. None [Selectable items] Make detail settings for various parameters. [Selectable items] Speaker Setup MENU 2.Manual Setup 1spkr None ) ) NOTE By default, the AVR-788’s “Amp Assign” setting is set to “ZONE2”. To use as the surround back speaker for the main zone, change the “Amp Assign” setting (vpage 28).
ENGLISH Getting Started Distance measurement Select the speaker you want to set, then set the distance. Set the value closest to the measured distance. [Variable range] Connections 0.0ft ~ 60.0ft : Display when “Feet” is set. 0.00m ~ 18.00m : Display when “Meters” is set. NOTE Setup Set the distance between the listening position and the various speakers to no more than 20.0 ft (6.00 meters). Playback Adjust channel levels to obtain equal volume from all speakers.
ENGLISH s 2ch Direct/Stereo Make settings for audio playback. Make speaker settings for 2-channel mode playback. Setting 2.Manual Setup 1.EXT.IN SW Level 2.2ch Direct/Stereo 3.Dolby Digital Setup 4.Auto Surround Mode 5.Manual EQ LFE To change the settings, select “Custom”. [Selectable items] Basic : Use the same settings as in “Speaker Setup”. +5dB +10dB : Select according to the player in use. Front 40Hz 60Hz Select front speaker size. 200Hz 250Hz : Select crossover frequency.
ENGLISH Getting Started d Dolby Digital Setup f Auto Surround Mode g Manual EQ Set dynamic range for downmix playback of Dolby Digital sources. Make setting for memorizing surround mode setting for each input signal type. Adjust tonal quality for each speaker using graphic equalizer. [Selectable items] [Selectable items] Connections ON : Compression is used. Select this if sound from front speakers is distorted. ON : Memorize settings.
ENGLISH f Power On Level Option Setup Make various other settings. F Menu screen F Define the volume setting that is active when the power is turned on. Make settings for audio playback in a ZONE2 system. 2.Manual Setup 2-4.Zone2 Setup Level Lch : 0dB Rch : 0dB Vol.Limit : OFF Power On Lev.: Last Mute Lev. : Full Last : Use the memorized setting from the last session. ––– : Always use the muting on condition when power is turned on. F Menu screen F 2.Manual Setup 1.Speaker Setup 2.HDMI Setup 3.
ENGLISH Getting Started s Volume Control d Source Delete Set the main zone volume setting. Remove input sources that are not used from the display. [Selectable items] Volume Limit Connections Make a setting for maximum volume. [Selectable items] OFF : Do not set a maximum volume. Setup –20dB : Set the maximum volume to –20 dB. –10dB : Set the maximum volume to –10 dB. Playback 0dB : Set the maximum volume to 0 dB.
ENGLISH k Setup Lock Change the Quick Select name. Up to 15 characters can be input. Protect settings from inadvertent change. h Remote ID Setup 1 2 3 4 NOTE j Display OFF : Turn protection off. • When “Setup Lock” is set to “ON”, the settings listed below can no longer be changed. Also, “SETUP LOCKED!” is displayed if you attempt to operate related buttons.
ENGLISH Getting Started n CD, AUX, CDR, DVD/HDP, TV/CBL, VCR, V.AUX This menu is for “CD”, “AUX”, “CDR”, “DVD/HDP”, “TV/CBL”, “VCR”, “V.AUX”. Input Setup F Menu screen F 3.Input Setup Connections Use this procedure to select the input source and make the settings related to playing input sources. n TUNER (AM/FM) Auto Preset CD Use the auto preset function to program radio stations. 1.Assign 2.Input Mode 3.Rename 4.Other [Input source] Setup Start : Start the auto preset process.
ENGLISH Set the input mode for this source. The selectable input modes depend on the input source and “Assign” setting (vpage 32, 33). TUNER AUTO [Selectable items] Assign input sources to input connectors. HDMI CDR DVD/HDP TV/CBL VCR : Detect type of digital input signal and decode and play automatically. PCM : Decode and play only PCM input signals. DTS : Decode and play only DTS input signals. TV/CBL VCR V.
ENGLISH Getting Started Digital In iPod dock Shuffle Select digital input connector to assign to this source. Assign Control Dock for iPod to this source. Make settings for shuffle mode. [Input source] CD AUX CDR DVD/HDP TV/CBL VCR [Input source] V.AUX Connections Setup Playback : Assign COAXIAL 1 input connector. COAX2 : Assign COAXIAL 2 input connector. OPT1 : Assign OPTICAL 1 input connector. OPT2 : Assign OPTICAL 2 input connector. None : No digital input connector assigned.
ENGLISH Automatically convert video input signal to monitor output format. [Input source] DVD/HDP TV/CBL VCR V.AUX [Selectable items] : Enable conversion. OFF : Disable conversion. Surround Modes Playing Multi-channel Sources (Dolby Digital, DTS, etc.) Standard Playback Source Level [Variable range] –12dB ~ 0dB ~ +12dB Surround Playback of 2-channel Sources To select these surround modes using the buttons on the remote control unit, press the STD button.
ENGLISH Getting Started DSP Simulation Playback [Selectable items] 7CH STEREO Setup : This mode is for enjoying stereo sound from all speakers. ROCK ARENA : This mode is for enjoying the atmosphere of a live concert in an arena. JAZZ CLUB : This mode is for enjoying the atmosphere of a live concert in a jazz club. Playback Connections The desired mode according to the program source and viewing situation can be selected from among 7 DENON original surround modes.
ENGLISH PANORAMA Soften the treble understanding. Parameter range of movie soundtracks for better [Selectable items] 4.Parameter ON : CINEMA EQ is used. OFF : CINEMA EQ is not used. DIMENSION Shift sound image center to front or rear, to adjust playback balance. D.COMP [Variable range] Compress dynamic range (difference between loud and soft sounds). [Selectable items] : Turn dynamic range compression off. LOW : Low setting. Adjust surround sound parameters.
ENGLISH Getting Started ROOM SIZE SB CH OUT (for Multi-channel sources) SB CH OUT (for 2-channel sources) Determine size of acoustic environment. Select playback mode for surround back channels. The surround back indicator lights. Determine whether to use surround back speakers. [Selectable items] small : Simulate acoustics of a small room. Connections med. s medium [Selectable items] OFF : No signal is played from the surround back channels.
ENGLISH d Room EQ f RESTORER Adjust the tonal quality of the sound. Select room equalizer for current environment. This function restores compressed audio signals to how they were before compression and corrects the sense of volume of the bass and treble to obtain richer playback sound. [Selectable items] Tone Defeat [Selectable items] : Playback without tone adjustment. OFF : Allow tone adjustment (treble, bass). Audyssey Byp.
ENGLISH Getting Started g Night Mode Audio Input Signal Optimized setting for late-night listening. Shows information about audio input signals. Information [Selectable items] Connections OFF F Menu screen F 5.Information : Turn night mode off. Information can be called out directly by pressing the DISPLAY button on the remote control unit. LOW : Low setting. MID : Middle setting. Status Setup HIGH : High setting. Shows information about current settings.
ENGLISH Auto Surround Mode Preset Station Shows information about HDMI input signals and monitor. Shows information about auto surround mode settings. The surround mode for which the last memory function was used for the different input signal types is displayed. Shows information about preset stations. F Menu screen F 5.Information Resolution 480p Color Space RGB 4:4:4 5.Information F Menu screen F 5.Information 1.Status 2.Audio Input Signal 3.HDMI Information 4.Auto Surround Mode 5.
ENGLISH Getting Started SOURCE SELECT BAND
ENGLISH Basic Operation Prepare the equipment. Set [MODE SELECTOR 1] to “AUDIO” or “VIDEO”. Set [MODE SELECTOR 2] to the component you want to operate. Start playback. Basic Operation 3 4 Press BAND to select “FM” or “AM”. Set [MODE SELECTOR 1] to “AUDIO”. (vpage 48 “Remote Control Unit Operations”) Press [MEMORY]. A1 ~ A8 B1 ~ B8 520 / 600 / 1000 / 1400 / 1500 / 1710 kHz, 90.1 / 90.1 MHz C1 ~ C8 90.1 MHz D1 ~ D8 90.1 MHz E1 ~ E8 90.1 MHz F1 ~ F8 90.1 MHz G1 ~ G8 90.
ENGLISH Getting Started
ENGLISH Either turn
ENGLISH Getting Started
ENGLISH “ZONE2 SOURCE” is shown on the display. ZONE2 SOURCE RECOUT XM ZONE2 TUNER ······ ···· RECOUT TUNER ZONE2 XM RECOUT SOURCE 5 Start recording. ” indicator lights. Play the program source. For operating instructions, refer to the respective equipment’s operating instructions. To record FM or AM broadcasts, select the broadcast (vpage 42). • The fader function does not affect the subwoofer. • The fader can be adjusted until the volume of the speaker adjusted to the lowest value is –12 dB.
ENGLISH Getting Started Quick Select Function Last Function Memory With this function, the currently playing input source, input mode, surround mode, room EQ settings and volume can be stored in the memory. This stores the settings as they were directly before the standby mode was set. When the power is turned back on, the settings are restored to as they were directly before the standby mode was set.
ENGLISH 3 Operate the audio component. [MAIN ON] • DENON and other makes of components can be operated by setting the preset memory. • This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the manufacturer of the component as shown in the list of preset codes (vEnd of this manual). • Operation is not possible for some models. 1 Set [MODE SELECTOR 1] to “AUDIO” or “VIDEO”.
ENGLISH Getting Started Functions of Buttons by Component n Front Connections [OFF] [SHIFT] [ON/SOURCE] [CHANNEL+/–] Device operated MODE SELECTOR 1 MODE SELECTOR 2 OFF ON/SOURCE Setup Playback Remote Control [1], [2], [3], [A/B], [0], [DISC SKIP +/ FAVORITE], [6 7], [8 9], [VCR CH+/–] Multi-Zone [MODE SELECTOR 1] CD Recorder MD Recorder Tape Deck DVD Player CD – iPod/ NETWORK – VIDEO TAPE / CD-R / MD – – DVD / VDP – Power off Power on – – – – 1 2 Preset channel selection 1-track/ a
ENGLISH Device operated MODE SELECTOR 1 MODE SELECTOR 2 NUMBER (0 ~ 9, +10) – – – – – TUNING (+, –) / TV VOL (+, –) Tuning (+, –) Tuning (+, –) Tuning (+, –) Tuning (+, –) Tuning (+, –) MODE / DVD MENU Switch search modes Switch search modes Switch search modes Switch search modes AUDIO – – Cable TV TV (Monitor) VIDEO TAPE / CD-R / MD DVD / VDP – – TV – Channels Channels Channels Volume control (+, –) Volume control (+, –) Volume control (+, –) Volume control (+, –) Calling
ENGLISH Getting Started Punch Through Function [Front] “Punch Through” is a function allowing you to operate 1, 2, 3, 0, 6, 7, 8 and 9 on CD, iPod/NETWORK, TAPE/CD-R/ MD, DVD/VDP or VCR components when in the SAT/CABLE or TV mode. By default, nothing is set. Connections Setup [1], [2], [3], [0], [6], [7], [8], [9] Playback Remote Control [MODE SELECTOR 1] [MODE SELECTOR 2] 1 2 3 4 Set [MODE SELECTOR 1] to “VIDEO”. Set [MODE SELECTOR 2] to the component to be registered (SAT/CABLE or TV).
ENGLISH Amp Assign / Multi-zone Connections and Operations F Multi-zone playback • 5.1-channel playback + ZONE2 stereo playback • 5.1-channel playback + ZONE2 monaural playback Main zone FL SW NOTE FR 5.
ENGLISH Getting Started Setting 2 : F 7.1-channel Setting 3 : With this setting it is possible to switch between the following two playback modes. playback F 5.1-channel playback F 2-channel playback Switching·················Surround Mode switching Main zone FL SW C FR Connections Main zone FL Amp Assign mode: 7.1ch SL SR 7.1ch C R Main zone Surround Mode Setup 5.1ch Playback Remote Control Speaker terminal Amp Assign mode 7.1ch FRONT CENTER R L FR FL C SURR.
ENGLISH F Making bi-amp connections for the FL and FR channels in the main zone and conducting 5.1-channel playback Multi-zone and Operations with Zone Output controlSettings unit Prepare pre-main amplifiers for ZONE2. Audio signals ZONE2 OUT Stereo Main zone (7.1-channel system) ZONE2 ZONE2 Main zone FL SW 5.
ENGLISH Getting Started SOURCE SELECT VOLUME Multi-zone Operations Adjusting the Volume GOperation on the main unitH Turning the Power On and Off q Press and select the zone to be adjusted. w Turn to adjust. Connections GOperation on the main unitH Press . When the power turns on, the multi-zone indicator ( on the display.
ENGLISH We recommend installing the speakers for the surround “L” and “R” channels a bit forward. Path of the surround sound from the speakers to the listening position We recommend using 2 speakers. When using dipolar speakers in particular, be sure to use 2 speakers. Other Information About Speaker Installation Surround back speakers 48 $ '3 Below we introduce examples of speaker layouts. Refer to these to arrange your speakers according to their type and how you want to use them.
ENGLISH Getting Started G2H When not using surround back speakers Front speakers Center speaker Connections Monitor Subwoofer 60° Surround speaker Setup Front speaker 2 to 3 feet / 60 to 90 cm Playback 120° Surround speakers Remote Control GAs seen from aboveH GAs seen from the sideH Surround Multi-Zone The AVR-788 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.
ENGLISH HDMI is a digital interface standard for next generation TVs based on DVI (Digital Visual Interface) standards and optimized for use in consumer equipment. Non-compressed digital video and multi-channel audio signals are transmitted with a single connection. HDMI is also compatible with HDCP (High-bandwidth Digital Contents Protection), a technology for protecting copyrights that encrypts digital video signals in the same was as with DVI.
ENGLISH Getting Started Surround Modes and Parameters Signals and adjustability in the different modes Channel output Surround mode Front L/R Center Surround L/R Parameter (default values are shown in parentheses) Connections Surround Back L/R Subwoofer D. COMP LFE z1 AFDM z2 z1 SB CH OUT CINEMA EQ.
ENGLISH Getting Started Signals and adjustability in the different modes Parameter (default values are shown in parentheses) Surround mode PRO LOGIC g/gx MUSIC mode only NEO:6 MUSIC mode only EXT.
ENGLISH Getting Started Differences in Surround Mode Names Depending on the Input Signals Input signals Button DTS Note Surround mode Connections ANALOG LINEAR PCM DTS ES DSCRT (With Flag) DOLBY DIGITAL DTS ES MTRX (With Flag) DTS (5.1ch) DTS 96/24 DOLBY DIGITAL EX (With Flag) DOLBY DIGITAL EX (With no Flag) DVD-AUDIO DOLBY DIGITAL (5.1/5/4ch) DOLBY DIGITAL (4/3ch) DOLBY DIGITAL (2ch) DVD-Audio (multi ch) DVD-Audio (2ch) STANDARD DTS SURROUND Setup Playback DTS ES DSCRT6.
ENGLISH DTS Note DOLBY DIGITAL DTS 96/24 DOLBY DIGITAL EX (With no Flag) DOLBY DIGITAL (5.1/5/4ch) DOLBY DIGITAL (4/3ch) DOLBY DIGITAL (2ch) S S S S S S A A A A A A ANALOG DTS ES DSCRT (With Flag) DTS ES MTRX (With Flag) DTS (5.
ENGLISH Getting Started Relationship Between Video Signals and Monitor Output Video convert Connections Setup ON Playback HDMI A A A A A A A A S S S S S S S S Remote Control S : Signal input A : No signal Input signals COMPONENT A A A A S S S S A A A A S S S S S-VIDEO A A S S A A S S A A S S A A S S VIDEO A S A S A S A S A S A S A S A S HDMI A A A A A A A A HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI MONITOR OUT COMPONENT S-VIDEO A A VIDEO VIDEO S-VIDEO S-VIDEO S-VIDEO S-VIDEO COMPONENT A z COMPONEN
ENGLISH MONITOR OUT HDMI COMPONENT S-VIDEO VIDEO A A A A VIDEO A A A S-VIDEO A A A S-VIDEO VIDEOz2 A A — VIDEO A A COMPONENT A A A z COMPONENT 1 VIDEO A A z COMPONENT 2 S-VIDEO A A COMPONENTz2 S-VIDEO VIDEOz2 A z COMPONENT 1 — VIDEO A HDMI A A A HDMI VIDEO A A HDMI S-VIDEO A A HDMI S-VIDEO VIDEOz2 A HDMI — VIDEO A HDMI COMPONENT A A z HDMI COMPONENT 1 VIDEO A z HDMI COMPONENT 2 S-VIDEO A HDMI COMPONENTz2 S-VIDEO VIDEOz2 z HDMI COMPONENT 1 — VIDEO A : Not output z1 : On-screen display superimposed on video s
ENGLISH Getting Started Symptom Power turns off suddenly and power indicator flashes red. Troubleshooting Connections Setup If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other components operating properly? If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
ENGLISH Page 25 GVideoH 29 • Set to something other than “None”. • Select a surround playback mode. • Turn on the subwoofer’s power. 24 • Set to “Yes”. 24 • Check the connections. 9 • Adjust the subwoofer’s volume to an appropriate level. • Set to the STANDARD mode. 46 Symptom No picture appears. 35 – No picture appears with HDMI connections. 34 32 25 DVDs cannot be copied on a VCR. • Cancel the PURE DIRECT mode.
ENGLISH Getting Started GiPodH Symptom iPod cannot be played. Cause Countermeasure Connections • The input source assigned to • Switch to the input source “iPod dock” is not selected. assigned at “iPod dock”. • Cable is not properly connected. • Reconnect. • Control Dock for iPod’s AC • Plug the Control Dock for iPod’s adapter is not connected to AC adapter into a power outlet. power outlet.
ENGLISH Getting Started Specifications n Tuner section • Power amplifier Front (A, B): Rated output: 90 W + 90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 120 W + 120 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Center: 90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 120 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.) Surround: 90 W + 90 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.) 120 W + 120 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.
List of preset codes / Liste de codes préréglés DVD Player A D H J K M P S T Z Curtis Mathes Aiwa Denon Hitachi JVC Konka Magnavox Mitsubishi Panasonic Philips Pioneer Sanyo Sony Toshiba Zenith 009 014, [111]z 010 006, 011 012, 013 005 004 014 005, 015, 016, 017 003, 008 018 002, 019, 020 001, 021, 022 023 Cybernex D E P R S Denon Magnavox Mitsubishi Panasonic Philips Pioneer RCA Sony 028, 029, 112 026 028 029, 030 026 028, 031 032 033, 034, 035, 036 Daytron DBX Dumont Dynatech Electrohome Electr
Midland Minutz Mitsubishi N Montgomery Ward Motorola MTC NAD National National Quenties NEC O P Nikko NTC Optimus Optonica Orion Panasonic Philco Philips Q R Pioneer Portland Price Club Proscan Proton Pulsar Quasar Radio Shack RCA S Realistic Saisho Samsung Sansui Sanyo SBR Schneider Scott Sears Sharp Siemens Signature Simpson Sony Soundesign Spectricon 001, 039, 048, 056, 057, 058, 065, 081, 083 125 066 001, 016, 039, 048, 056, 057, 058, 065, 081, 082, 083, 105 011, 020, 144, 145, 146 121, 147 03
www.denon.com Denon Brand Company, D&M Holdings Inc. Printed in China 00D 511 4631 108 3.AVR788E3_PRESET_108.