Operation Manual
16
ENGLISH
6
Trim B point
u Turn Jog Wheel to move
the B point 1 frame at a
time.
• Range for trimming B point is limited as
follows.
B point for Loop:
Between 5 frames after A point and
disc end.
B point for Splice:
±30 frames from the original B point.
(However, when the B point was loaded
from the standby mode, the B point
cannot be moved backwards. So, use
A/B Move function)
B point for Sampler:
Between 5 frames after A point and
sampler end.
A/B Move
8
Select A and B points
o Select or the A/B Move and
push the A button for the A
point you want to move. The
standby mode is set at the A
point and the A button
illumination flashes.
!0 To select the B point, push
the B button after selecting
the A point.
• The B LED flashes. The
Selected B point is used for the A1 or A2
point that was first selected.
A 1
B
11
Cancel the A-B Trim or A/B Move
!3 Push the A/B TRIM button to
cancel the mode.
SPLICE
A/B TRIM
10
A/B TRIM
RVS
PLAY/PAUSESTUTTER AUTO
REMOTE CONTROLLER RC-D90
0%
TRACK
PARAMETERS
PITCH BEND
PITCH/KEY
PITCH/VOL
SPLICE
A/B TRIM
4 HOT START
SAMPLER
STOP
B
SAMP2
EXIT/RELOOP
SAMP1
A3 A4 CUE
A1 A2
CLR
CLR
F
X
PLASTUTTER
S
SAMP2SAMP1
A3 A4 CUE
A1 A2
CLR
CLR
RVS
A 3/4
PUSH
ON/OFF
MEMO
PRESET
RANDOM
PROGRAM
TIME
TOTAL TIME
RELAY
CONT./SINGLE
ALL OFF
PLATTER MODE
MEMO
PRESET
TIME
TOTAL TIME
RELAY
CONT./SINGLE
sm
CONT.
f
SINGLE
B
B
A4
A2
REMAIN
s
m
TOTAL
BA3
BA1
ELAPSED
m
CONREMAIN
s
m
TOTAL
BA3
BA1
ELAPSED
DRAG S.
DUMP
BRAKE
RVS
ECHO
KEY ADJ.
PROG
MEMO
PROG
MEMO
CUE
FLIP
FLIP
A 3
A 1
A 4
A 2
B
B
EXIT/
RELOOP
RELOOP
EXIT/
CUE
OPEN/
CLOSE
TAP
CUE
FLIP
FLIP
A 3
A 1
A 4
A 2
-TRACK PLAY-TRACK HOT START
S
E
A
H
C
L
F
M
X
G
F
L
D
E
F
I
R
L
B
E
D
N
H
C
S
E
A
/
D
B
E
R
N
R
D
I
S
O
E
C
R
U
L
L
F
F
O
RANGE
B
Y
S
S
A
A
P
S
E
T
C
E
H
C
T
R
C
S
L
A
-TRACK HOT START
wq, !3
r, u, !1
y, i, !0, !2
e, t, o, !2
1
Select A-B trim mode
First select whether to adjust the A and B
points using the A-B trim mode or the A/B
move mode.
q Push the A/B TRIM button to
set the A and B point position
adjustment mode.
w Now turn the
PARAMETERS knob to
select the A-B Trim or the
A/B Move.
3
Trim A point
r Turn the Jog Wheel to
move the A point 1 frame
at a time.
• Range for trimming A point is limited as
follows.
A point for Loop:
±30 frames from the original A point.
(However, when the A point was
loaded from the standby mode, the A
point cannot be moved backwards.
So, use A/B Move function)
A point for Splice:
Between the beginning of the disc and
5 frames before B point.
A point for Sampler:
Between the original A point and 5
frames before B point.
SPLICE
A/B TRIM
2
Select A point (in A-B Trim)
e Select the A-B Trim and push
the corresponding A button
for the loop to be trimmed.
The A button illumination
flashes and loop playback
starts.
• In the splice trim mode, total 6 seconds
of spliced section (started from 2
seconds before A point to 4 seconds
after the B point) is played.
A 1
5
Select B point (in A-B Trim)
y Select the A-B Trim mode and
to select the B point, push the
B button after selecting the A
point.
Then push the B button. The B LED
flashes and the B point trim become
enable.
• The seamless loop, sampler loop and splice A and B points can be fine-adjusted using Jog Wheel.
• There are two ways for doing this.
A-B Trim: Trim the points during loop playback as a rehearsal.
A/B Move: Move the points using the Manual Search. A/B Move can not be used with Sampler loop.
TRACK
PARAMETERS
PUSH
ON/OFF
B
A/B TRIM
4
Save the A point
t Push the A button again to
save new A point, and the
unit automatically exit from
the A-B Trim mode.
A 1
7
Save the B point
i Push the B button again to
save new B point, and the
unit automatically exit from
finish the A-B Trim mode.
B
9
Move A or B points
!1 Turn the Jog Wheel to move
the selected point using the
Manual Search function.
• Range for moving A point is limited as
follows.
A point for Loop:
Between the beginning of the disc and
5 frames before B point.
A point for Splice:
Between the beginning of the disc and
5 frames before B point
• Range for moving B point is limited as
follows.
B point for Loop:
Between 5 frames after A point and
disc end
B point for Splice:
Between 5 frames after A point and
disc end
10
Save the A or B points
!2 Push the A1/A2 or B button
again. The LED stops flashing
and the A1/A2 or B point is
saved, and the unit
automatically exit from the A/B
Move mode.
B