MULTI CHANNEL POWER AMPLIFIER POA-3012CI Owner’s Manual Bedienungsanleitung 1.POA-3012CI_ENG_101.
ENGLISH DEUTSCH n SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
DEUTSCH n NOTE ON USE / HINWEISE ZUM GEBRAUCH ENGLISH n For Europe model DECLARATION OF CONFORMITY We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of 2006/95/EC and 2004/108/EC Directive. ÜBEREINSTIMMUNGSERKLÄRUNG • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack.
ENGLISH Getting Started n Contents Getting Started Connections Accessories·······················································································1 Cautions on Handling······································································1 Cautions on Installation··································································1 Part Names and Functions······························································2 Front Panel·······························································
ENGLISH Getting Started Part Names and Functions For buttons not explained here, see the page indicated in parentheses ( ).
ENGLISH Getting Started Rear Panel Q0 o i u y t Connections Setup Operations Troubleshooting Specifications q w q ETHERNET connector···································· (8) w RS-232C connector········································ (9) e Speaker terminals (SPEAKER SYSTEMS)···································· (5) r AC inlet (AC IN)············································ (10) t AUDIO INPUT connectors····························· (7) e r y TRIGGER IN jacks··································
ENGLISH Getting Started Connections Cables Used for Connections The POA-3012CI incorporates six sets of 2-channel amplifier from ZONE1 to ZONE6. The same audio signal can be output from all ZONE or separate signals can be output from each ZONE. The POA-3012CI also supports BRIDGED output. Before making the connections, determine the input signals and output signals for each ZONE and then set up the POA-3012CI in accordance with the following procedure.
ENGLISH Getting Started Speaker Connections Connections Connection Method When Outputting 2 Channels From One ZONE CH 1 CH 2 CH 3 CH 4 CH 9 CH 10 CH 11 CH 12 Connection Method for BRIDGED Output Setup • In BRIDGED mode, one channel is output from one ZONE. • To set BRIDGED mode, select “BRIDGED” as the “OPERATION MODE” on the “Main Setup” menu. • When BRIDGED out putting a signal input to the AUDIO INPUT terminal, input to an even-numbered input terminal.
ENGLISH Carefully check the channel numbers and + (red) and – (black) polarities on the speakers being connected to the POA-3012CI, and be sure to interconnect the channels and polarities correctly. Peel off about 0.03 ft/10 mm of sheathing Turn the speaker terminal counterclockwise to loosen it. the hilt into the speaker terminal. tighten it. When using a banana plug (for North America model) Specifications Tighten the speaker terminal firmly before inserting the banana plug.
ENGLISH Getting Started Input Connections BUS INPUT Connections Connections • To play signals input to the BUS INPUT terminal, select the channel using “INPUT SELECT” on the “Main Setup” menu. • When “BUS L+R” is used, signals input to BUS INPUT L and R are mixed and output as monaural.
ENGLISH Required System ETHERNET Connections Computer A broadband line connection to the Internet is required in order to use the POA-3012CI’s firmware update. n Modem n Router To LAN port LAN port/ Ethernet connector n Ethernet Cable (CAT-5 or greater recommended) Router • If you have an Internet provider contract for a line on which network settings are made manually, make the settings at “Network Setup” (vpage 15).
ENGLISH Getting Started External Controller RS-232C connector Connections This connector is used for an external controller. Setup Operations b If you wish to control the POA-3012CI from an external controller using the RS-232C connector, perform the operation below beforehand. q Turn the POA-3012CI’s power. w Turn off the POA-3012CI’s power from the external controller. e Check that the POA-3012CI is in the standby mode.
ENGLISH Wait until all connections have been completed before connecting the power cord. Getting Started Connecting the Power Cord Setup Using the menu n To select the item to be set Turn the SELECT / ENTER knob until the item you want to set appears. Press the SELECT / ENTER knob or the i button. n To return to higher level menu items Press the u / RETURN button. n To confirm selected item Press the SELECT / ENTER knob.
ENGLISH Getting Started Menu Map Connections Main Setup NORMAL MODE (vpage 13) CH 1 CH 2 CH 3 a VOLUME CONTROL (vpage 13) 0.0dB –90.0dB – – –.–dB Setup CH 12 Operations CH 1 CH 2 CH 3 s INPUT SELECT (vpage 13) Troubleshooting CH 1 CH 2 CH 3 (vpage 13) AUX.1 BUS L BUS R BUS L+R Specifications (vpage 13) g Z ONE TRIGGER ON MODE (vpage 14) h DIMMER MODE (vpage 14) Network Setup Option Setup j P OWER CONFIGURATION BTL 0.0dB BTL –90.0dB BTL – – –.
ENGLISH Getting Started Main Setup Network Setup a N etwork Information (vpage 14) DHCP Connections (vpage 14) IP Address Mac Address Setup Operations DHCP OFF ON IP Address Subnet Mask Default Gateway Primary DNS Secondary DNS Address Name Option Setup (vpage 16) Specifications Proxy ON OFF Troubleshooting s Network Setup (vpage 15) Proxy Address Port Proxy Name Port a Setup Lock (vpage 16) s Maintenance (vpage 16) d Firmware Update (vpage 16) 12 1.POA-3012CI_ENG_101.
ENGLISH Getting Started Main Setup F Menu tree F Main Setup a VOLUME CONTROL Connections s INPUT SELECT d LOW CUT FILTER s INPUT SELECT f OPERATION MODE Sets the input terminal for each channel. Sets the output method for channels in each ZONE. [Selectable Channels] [Selectable Channels] For details of the channels which can be set in each mode, see GSelectable ChannelsH in “a VOLUME CONTROL”. Sets each of the following channel pairs.
ENGLISH j POWER CONFIGURATION Sets the operating specifications for the power amplifiers of each ZONE. Select the method for turning on the POA-3012CI. [Selectable items] POWER BUTTON For details of the channels which can be set in each mode, see GSelectable ChannelsH in “f OPERATION MODE” (vpage 13). ON LINE [Selectable items] F Menu tree F : Operate with the ON/STANDBY button only. : Operate from an external device via Ethernet or RS-232C input. A.
ENGLISH Getting Started s Network Setup Make settings for wired LAN. Wired LAN settings Connections Use this procedure to configure the Wired LAN settings. Setup 1 2 Connect the LAN cable (vpage 8). Turn on the POA-3012CI (vpage 17). POA-3012CI performs automatic network setup due to the DHCP Operations Troubleshooting 3 function. When connecting to a network that has no DHCP function, perform the setting in step 3. Set the IP address at the menu “Network Setup” – “Network Setup”.
ENGLISH u Press the SELECT/ENTER knob. Setup is complete. Option Setup a Setup Lock s Maintenance d Firmware Update Protect settings from inadvertent change. [Selectable items] ON : Turn protection on. OFF : Turn protection off. You can check for firmware updates. You can also check approximately how long it will take to complete an update. Update Start Execute the update process. When updating starts, the power indicator lights red. “Updating zzz” is shown on the display during updating.
ENGLISH Getting Started Operations ZONE operation mode indicators SELECT/ENTER Connections Check the Status of Each Channel 1 Press the DISPLAY button. Setup b Zone status is indicated on the bottom line of the display. b Turn the SELECT / ENTER knob to change the display as follows. Operations Channel No. & INPUT Line ON/STANDBY ZONE 5 Troubleshooting DISPLAY u/ RETURN Turning the Power On Specifications Press the ON / STANDBY button.
ENGLISH Operate. GExample: 3H Warning and Protection Data Screen To use the web control function, set the menu “Main Setup” – “POWER CONFIGURATION” – “ON LINE” (vpage 14). GExample: 1H Channel Setup Screen Click when you update to the latest information (z) NOTE GExample: 4H Audio Signal and Trigger Input Screen Enter figures or click “< ” or “>” to make the setting, and then click “Set”. GExample: 2H System Setup Screen Click “v” and select from the displayed items.
ENGLISH Getting Started Troubleshooting Specifications Connections Check the following before assuming there is a problem with the set: 1. Are all connections proper? 2. Is the set being operated as described in the owner’s manual? 3. Are the speakers and input components being operated properly? If the set does not seem to be operating properly, check the points listed below. If these points do not apply, the set may be damaged. Turn off the power immediately and contact your store of purchase.
www.denon.com Denon Brand Company, D&M Holdings Inc. Printed in Japan 00D 511 4719 101 3.POA-3012CI_Back_101.
