REMOTE CONTROL UNIT RC-7000CI OWNER’S MANUAL
1. 2. 3. 4. 5. 6. 7. IC Information (For Canadian customers) FCC Information (For US customers) 1. DEVICE RC-7000CI IC: 6963A-RC7000 This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. APPAREIL RC-7000CI IC: 6963A-RC7000 Cet appareil est conforme à la norme CNR-210 du Canada.
A NOTE ABOUT RECYCLING: This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local recycling regulations. When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning battery disposal.
• DECLARATION OF CONFORMITY Hereby, D&M Holdings Inc., Denon Brand Company declares that this product RC-7000CI is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC, in conformity with the following standards; EN300328, EN301489-01 and EN301489-17 The declaration of conformity may be consulted to our European representative, DENON EUROPE. • ÜBEREINSTIMMUNGSERKLÄRUNG Hiermit erklärt D&M Holdings Inc.
Inserting the batteries q Lift the clasp and remove w Load the four batteries the rear lid. properly as indicated by the marks in the battery compartment. Operation Thank you for purchasing this DENON product. To ensure proper operation, please read these owner’s manual carefully before using the product. After reading them, be sure to keep them for future reference.
Getting Started Operating range of the remote control unit Point the remote control unit at the remote sensor when operating it. Part names and functions For buttons not explained here, see the page indicated in parentheses ( ). Operation q w e 30° Network function 30° Approx.
Initial display screen Make the setting described below. The initial display settings are shown on the display below. 1 When buttons on the remote control unit are pressed, various settings and operation items appear on the LCD screen. n Operation for selecting 4 Press DEVICE. VCR 1 iPod ZONE3 ZONE4 VCR 2 NetAud TUNER CD DVD TV SAT Page 1/2 Press NEXT. After “PLEASE WAIT” is displayed, the default device is set to [Denon1].
Getting Started Settings menu map n BASIC SETUP (vpage 7, 9) • BRAND SET • CODE SEARCH Operation n FAVORITES (vpage 10, 19) Network function • ADD / REDO • DELETE • CONFIGURE · FAV DEVICE · FAV IR DELAY · TOTAL DIGITS · CHANNEL KEY n MACROS (vpage 8, 9, 19) PC Application • ADD / REDO • DELETE • EDIT DELAY n PUNCH THRU (vpage 11, 19) Troubleshooting • ADD · CHANNEL TUNE · TRANSPORTS · VOLUME CONT. · MENU NAVIG. • CLEAR · CHANNEL TUNE · TRANSPORTS · VOLUME CONT. · MENU NAVIG.
LCD button LCDボタン NEXT 1 2 Press DEVICE. Setting the screen display time The “DEVICE SELECT” menu is displayed. Use this procedure to set the time until the screen display turns off. Initial setting: 5 seconds Press the LCD button for the device (equipment) you want to operate. b If there are multiple pages, use the NEXT and BACK button to switch screens. 3 Press the LCD button for the item you want to operate. Press twice, then press [USER Press . Press Press RC SETUP for 3 seconds.
Getting Started LCD button LCDボタン LCD button LCDボタン Setting the backlight on time Adjusting the contrast Use this procedure to set the time until the backlight turns off. Initial setting: 5 seconds Set this if the characters on the screen are hard to see. Initial setting: Level 5 1 RC SETUP 2 PREF] NEXT 3 [LIGHT T/O] 4 NEXT 5 [–LIGHT T/O+] Press Operation BACK DEVICE Network function 6 8 3 NEXT for 3 seconds. The “PROGRAM DEVICE” menu is displayed. twice, then press [USER Press .
Using the preset memory function 8 VOL+1– 2 , 3, 6, 7, 8, 9, to check whether the device to be added operates. Operates......................................... [YES] Use The remote control unit can be preset to operate devices of various brands. • The IR/RF selection screen appears. Does not operate............................ [NO] Press RC SETUP for 3 seconds. • The screen switches to the next code. Find the code that operates and set it by pressing [YES]. The “PROGRAM DEVICE” menu is displayed.
Getting Started 7 LCD button LCDボタン Operation BACK DEVICE LCD button LCDボタン Place the remote control units with their signal transmitters facing each other, press NEXT, then immediately press the button on the remote control unit you want to register. NEXT Using the Macro function This function allows you to register a series of operations at a single button.
Press RC SETUP. Using the delay time function Using the code search function The registration menu is displayed. The interval at which the remote control signals registered with the system call function are sent (the “delay time”) can be set. This function lets you search for preset codes when adding new devices (equipment) to the remote control unit. Press [SAVE] to register the set macro. Press [EXIT] to end the setting. NOTE Press [MACROS]. Press [EDIT DELAY]. Press NEXT twice.
Getting Started Favorites settings LCD button LCDボタン LCD button LCDボタン Use this function to register your favorite channel numbers so they can be operated with a single button. Favorites settings NEXT Operation ENTER Network function RC SETUP PC Application Troubleshooting About the button names in these explanations [ ] :L CD buttons for selection items Button name only: Indicates a button on the remote control unit 1 2 3 4 5 Press RC SETUP for 3 seconds.
Input the number (channel) you want to register. Press NEXT. Press [SAVE] to register the favorite. 11 Press [EXIT] to end the registration. Press [ADD] to continue registering. Press At the “Punch Thru” screen, press the LCD for the group you want to set. The functions for which punch thru can be assigned in units of groups are as shown on the table below. Groups CHANNEL TUNE TRANSPORTS The“PROGRAM DEVICE” menu is displayed. Press [PUNCH THRU]. Press [ADD]. 6 NEXT 7 LCD button Press .
Getting Started Deleting pages LCD button LCDボタン BACK LCD button LCDボタン NEXT Operation Network function RC SETUP PC Application 1 2 3 4 5 Press RC SETUP for 3 seconds. 6 7 Select the page to be deleted using NEXT and BACK, then press [SELECT PAGE]. The “PROGRAM DEVICE” menu is displayed. Press NEXT, then press [EDIT PAGE]. Press [DELETE PAGE]. Press NEXT. Press [MAIN] to delete a page from the device select menu, [DEVICE] to delete a device (equipment) page. Press [YES]. The page is delete.
Copying devices Deleting devices 6 7 LCD button Press Press , then press Press . Press . . At the “Source Device” screen, press the for the device you want to move. Press NEXT. At the “Target Device” screen, press the button in the place you want to insert. Press for 3 seconds. The “PROGRAM DEVICE” menu is displayed. Press Press Press The device is moved. . . At the “Source Device” screen, press the for the device (equipment) you want to copy. Press NEXT.
Getting Started Setting the device display mode LCD button LCDボタン LCD button LCDボタン Use this procedure to select the way in which the devices (equipment) are displayed. 1 [EDIT DEVICE] 2 NEXT 3 [DISPLAY MODE] 4 NEXT LCD 5 button Press RC SETUP for 3 seconds. The “PROGRAM DEVICE” menu is displayed.
The “PROGRAM DEVICE” menu is displayed. Press Press . 1 RC SETUP [EDIT TEXT] 2 NEXT 3 [DEVICE NAME] 4 button Press for 3 seconds. Press [RF], then press [YES]. Press NEXT. Press . . At the “Select Device” screen, press the LCD for the device (equipment) whose name you want to change. 5 6 7 Press NEXT. At the “Edit Text” screen, use the first column of LCD buttons to select the position of the character to be edited.
Getting Started Inserting buttons LCD button LCDボタン NEXT 1 RC SETUP 2 NEXT 3 [COPY] 4 NEXT 5 LCD button 6 button 7 NEXT 8 LCD button 6 button 7 NEXT 8 LCD 9 10 [YES] for 3 seconds. Press The “PROGRAM DEVICE” menu is displayed. Operation Press , then press Press . Press . . Network function At the “Select key” screen, press the LCD for the button you want to move.
Press for 3 seconds. The “PROGRAM DEVICE” menu is displayed. Press , then press [EDIT FUNC]. Press Press 1 RC SETUP 2 NEXT 3 NEXT 4 NEXT 5 LCD button 6 button 6 NEXT 7 button Press for 3 seconds. At the “Select key” screen, press the LCD for the button you want to delete. , then press Press [YES]. The button is deleted. b When [NO] is pressed, the setting menu reappears. To continue, press [YES]. . . .
Getting Started Changing the button name 1 2 NEXT 3 [KEY NAME] 4 button Press RC SETUP for 3 seconds. LCD button LCDボタン LCD button LCDボタン NEXT The “PROGRAM DEVICE” menu is displayed. Operation 5 button 1 RC SETUP 2 [LEARNING] 3 [ERASE LEARN] 4 NEXT 5 LCD button 6 7 6 7 Press , then press [EDIT TEXT]. Press . At the “Select Device” screen, press the LCD for the device whose button name you want to change.
The “PROGRAM DEVICE” menu is displayed. Press Press Press . . twice. To delete, press [YES]. If you do not want to delete, press [NO]. b Press [NO] to end, [YES] to continue. for 3 seconds. The “PROGRAM DEVICE” menu is displayed. Press . Press . Press twice. At the “Source Device” screen, press the for the device (equipment) you want to delete. 6 button 7 At the “Select key” screen, press the LCD for the button you want to delete. To delete, press [YES].
Getting Started LCD button LCDボタン LCD button LCDボタン NEXT Operation Network function RC SETUP PC Application Troubleshooting About the button names in these explanations [ ] :L CD buttons for selection items Button name only: Indicates a button on the remote control unit Specifications 20 Operational reset User reset The settings are returned to as they were upon purchase. This procedure deletes the macro settings added by the user and the remote control codes that have been learned.
Unlock function When locked, device (equipment) editing is not possible. This procedure unlocks devices (equipment) that have been locked. Press for 3 seconds. The “PROGRAM DEVICE” menu is displayed. Press , then press [RESET/LOCK]. Press Press . twice. Press [YES]. b When [NO] is pressed, the setting menu reappears. To continue, press [YES]. for 3 seconds. The “PROGRAM DEVICE” menu is displayed. Press , then press [RESET/LOCK]. Press Press . twice.
Getting Started NOTE Network function Operation This functions uses the RC-7001RCI (sold separately). When a wireless (RF) network is established using the RC-7001RCI (sold separately), the RC-7001RCI is called a node. An individual node number is registered for each RC-7001RCI unit.
LCD button LCDボタン LCD button LCDボタン NEXT Use this procedure to register a node number and add an RC-7001RCI (sold separately) to the network. Press RC SETUP for 3 seconds. The “PROGRAM DEVICE” menu is displayed. Press NEXT twice, then press [NETWORK]. Press [ADD NODES]. Press NEXT. Press RESET/CONFIG on the RC-7001RCI (sold separately) for about 1 second. The indicator flashes green. 7 Press NEXT twice. “Success!” is displayed when the device has been added successfully.
Getting Started LCD button LCDボタン LCD button LCDボタン NEXT Operation Network function RC SETUP Deleting nodes Viewing nodes Use this procedure to delete RC-7001RCI (sold separately) units by specifying the node number from the current network. Use this procedure to search for and display a list of RC7001RCIs (sold separately) registered in the network. 1 2 3 4 PC Application 5 6 Press RC SETUP for 3 seconds. The “PROGRAM DEVICE” menu is displayed. Press NEXT twice, then press [NETWORK].
Use this procedure to add labels to RC-7001RCIs (sold separately) for easier distinction. The “PROGRAM DEVICE” menu is displayed. Press NEXT twice, then press [NETWORK]. Press [EDIT LABEL]. Press NEXT twice. The RC-7001RCI’s (sold separately) node number is displayed. Select the node number to be changed, then press NEXT. The edit screen for the selected node appears. Select the character to be input with the second column of LCD buttons, then press [SELECT].
Getting Started PC Application RC-7000CI Editor function Operation n You can use “RC-7000CI Editor” for the following operations. • Editing RC-7000CI setting data. • Backing up RC-7000CI setting data on the PC. • Remote control code database downloading. Network function n Recommended devices and environment required for using “RC-7000CI Editor”. PC Application • Personal computer running Windows® XP Service Pack2 operating system. • HDD with sufficient free disk space. • USB 2.
Specifications Cause 1 2 • Remove the obstacle. 2 • Insert the batteries in the proper direction, following the polarity marks in the battery compartment. • Move the set to a place in which the remote control sensor will not be exposed to strong light. 2 • Brightness setting is inappropriate. • Adjust the screen’s brightness “Adjusting the contrast”. at 6 • Radio interference with other devices. • Move away from microwave ovens, devices using a wireless LAN, or other wireless devices.
TOKYO, JAPAN www.denon.com Denon Brand Company, D&M Holdings Inc.
