AV SURROUND RECEIVER AVR-2308CI Owner’s Manual Manuel de l’Utilisateur
ENGLISH FRANCAIS SAFETY INSTRUCTIONS n SAFETY PRECAUTIONS 1. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
FRANCAIS ENGLISH FCC INFORMATION (For US customers) n NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION 1. PRODUCT This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this product may not cause harmful interference, and (2) this product must accept any interference received, including interference that may cause undesired operation. 2.
ENGLISH Contents Getting Started Accessories·······················································································2 Cautions on Handling······································································3 Cautions on Installation··································································3 About the Remote Control Unit·····················································3 Inserting the Batteries·····································································3 Operating Range
ENGLISH Troubleshooting····································································67 ~ 69 List of preset codes············································ End of this manual Accessories Playback Specifications················································································ 70 Thank you for purchasing this DENON product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading them, be sure to keep them for future reference.
ENGLISH Getting Started Cautions on Handling About the Remote Control Unit • Before turning the power switch on Check once again that all connections are correct and that there are no problems with the connection cables. Connections • Power is supplied to some of the circuitry even when the unit is set to the standby mode. When traveling or leaving home for long periods of time, be sure to unplug the power cord from the power outlet.
ENGLISH For buttons not explained here, see the page indicated in parentheses ( ).
ENGLISH Getting Started Rear Panel Q3 Q2 Q1 Q0 o Connections Setup Playback Remote Control Q7 Q4 Q5 Q8 Q4 Q6 Multi-Zone Information Troubleshooting q w e q RS-232C connector······································ (19) w REMOTE CONTROL jack····························· (19) e TRIGGER OUT jacks···································· (19) r DOCK CONTROL jack·································· (14) t Speaker terminals (SPEAKERS)··················· (9) y SIGNAL GND terminal····························
ENGLISH [ Rear ] n Main Remote Control Unit (RC-1080) [ Front ] w y e Q0 ENTER button········································ (20, 48) y Q4 u Q5 Q6 Q1 n Sub remote control unit for ZONE2 (RC-1084) q w i o Q0 Q0 e r t y NOTE If buttons on the front or rear are pressed strongly, the button on the opposite side will be activated too.
ENGLISH Getting Started Preparations Connections Connections Setup Connections for all compatible audio and video signal formats are described in these operating instructions. Please select the types of connections suited for the equipment you are connecting. With some types of connections, certain settings must be made on the AVR-2308CI. For details, refer to the instructions for the respective connection items below.
ENGLISH GFlow of video signals inside the AVR-2308CIH Component video connectors S-Video connector S-Video connector Video connector Video connector Video inputs Video outputs Monitor On-Screen Display for Component Video Outputs and HDMI Output • When viewing HDMI or component video signals via the AVR-2308CI, the on-screen display appears when the MENU button or the main remote control unit’s DISPLAY button is operated.
ENGLISH Getting Started Speaker Connections Speaker Connections Example: 5.1-channels (FRONT A+B) and ZONE2 use Speaker Installation Connections The illustration below shows a basic example of installation of the amplifier combined with 8 speakers and a monitor.
ENGLISH Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to the AVR-2308CI, and be sure to interconnect the channels and polarities correctly. Insert the speaker cable’s core wire to the hilt into the speaker terminal. Remote Control Turn the speaker terminal counterclockwise to loosen it. Playback 2 3 4 Setup Peel off about 0.
ENGLISH Getting Started Connecting Equipment with HDMI connectors NOTE With HDMI connections, the video and audio signals can be transferred with a single cable. Connections DVD player Monitor )%.* 065 )%.* */ b The AVR-2308CI is equipped for HDMI version 1.3a. This version is compatible with other versions, allowing connection to all components equipped with an HDMI connector. b The AVR-2308CI is compatible with 30- and 36-bit Deep Color.
ENGLISH Connecting the Playback Components • Connect the cables to be used (vpage 8 “Video Conversion Function”). • With HDMI connections, the video and audio signals can be transferred with a single cable. • To output the audio signals to the monitor with HDMI connections, set menu “Manual Setup” – “HDMI Setup” – “HDMI Audio Setup” to “TV” (vpage 27). 7*%&0 )%.* */ 7*%&0 */ 4 7*%&0 */ $0.
ENGLISH Getting Started Record Player CD Player Turntable (MM cartridge) Connect the cables to be used. CD player "6%*0 Connections "6%*0 065 3 Setup "6%*0 065 R L R (/% L Playback L $0"9*"065 R Remote Control Multi-Zone Information Troubleshooting • When connecting a record player with an MC cartridge, use a commercially available MC head amplifier or a step-up transformer.
ENGLISH TV/CABLE Tuner Use a DENON Control Dock for iPod (ASD-1R, ASD-3N or ASD-3W, sold separately) to connect the iPod to the AVR-2308CI. For instructions on the Control Dock for iPod settings, refer to the Control Dock for iPod’s operating instructions. TV tuner 7*%&0 )%.* 065 Example 2: iPod Connect the cables to be used. iPod 4 7*%&0 065 $0.
ENGLISH Getting Started Connecting the Recording Components Video Cassette Recorder Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly. Connect the cables to be used. Video cassette recorder 7*%&0 Connections Digital Video Recorder "6%*0 4 7*%&0 */ 065 7*%&0 065 */ "6%*0 */ - Connect the cables to be used.
ENGLISH Make analog connections if you wish to record analog audio signals, or digital connections if you wish to record digital audio signals, depending on the types of connectors on the components being used.
ENGLISH Getting Started Component with Multi-channel Output connectors DVD player / Super Audio CD player / External decoder "6%*0 Connections 46# 800'&3 '30/5 - 3 $&/5&3 463306/% - 3 463306/% #"$, - 3 R L R L R L R L R L R • The AVR-2308CI is an XM Ready® receiver. You can receive XM® Satellite Radio by connecting to the XM Mini-Tuner and Home Dock (includes home antenna, sold separately) and subscribing to the XM service.
ENGLISH Getting Started Antenna terminals An F-type FM antenna cable plug can be connected directly. Direction of broadcasting station Connections AM loop antenna (supplied) FM antenna Setup Playback 75 Ω/ohms Coaxial cable Remote Control FM indoor antenna (supplied) Multi-Zone Connection of AM antennas 1. Push the lever. 2. Insert the conductor. 3. Return the lever. Information Ground AM outdoor antenna Connect to the AM antenna terminals.
ENGLISH Getting Started Multi-zone External Controller ZONE2 out Connections Connections If another pre-main (integrated) amplifier is connected, the ZONE2 out connectors can be used to play a different program source in ZONE2 at the same time (vpage 54 ~ 57). This connector is used for an external controller. Pre-main amplifier (ZONE2) b If you wish to control the AVR-2308CI from an external controller using the RS-232C connector, perform the operation below beforehand.
ENGLISH Wait until all connections have been completed before connecting the power cord. Connection to the AC outlets With the AVR-2308CI, settings and operations for most functions can be performed by operating while looking at the menus displayed on the monitor screen. MENU ui The same operation is possible on the main unit or remote control unit. RETURN ENTER, op [Front] uiop ENTER [MODE SELECTOR 1] Press ui again to select the item you want to set, then press ENTER.
ENGLISH Getting Started Example of Display of Default Values Connections In lists of selectable items or adjustable ranges, the item surrounded by a border is the default value. Examples of On-screen Display and Front Display Some typical examples are described below. GFront displayH GOn-screen displayH Screen title [Selectable items] A MENU Q Menu number *MENU Auto Setup Submenu title B A+B 1.Auto Setup 2.Manual Setup 3.Input Setup 4.Parameter 5.Information Setup Playback 1-1.
ENGLISH Getting Started Menu Map Auto Setup (vpage 23 ~ 25) MENU n Option • Room EQ • Direct Mode Setup n Parameter Check • Speaker Configuration Check • Distance Check • Channel Level Check • Crossover Frequency Check • EQ Check • Restore Connections n Start Menu • Step 1: Speaker Detection • Step 2: Measurements • Step 3: Calculation • Step 4: Check • Step 5: Store Setup 1.Auto Setup 2.Manual Setup 3.Input Setup 4.Parameter 5.
ENGLISH Getting Started Preparations 1 MIC Connect the included setup microphone to the SETUP jack on the main unit. Auto Setup The “Auto Setup” screen appears automatically. Connections Setup Playback Remote Control • This procedure lets you measure the acoustic properties of your speakers and listening room and make the optimum settings automatically.
ENGLISH Step 1 : Speaker Detection Optimize settings for speakers in use. F Menu screen F 1-1.Start Menu The settings are performed automatically. Start auto setup and output the test tone. Set as desired before starting the auto setup procedure. The front speaker to be measured can be selected ahead of time here. The listening environment with respect to the listening position (“Speaker size check”, “Crossover Frequency check” and “Room EQ correction”) is measured automatically at positions 2 to 6.
ENGLISH Getting Started Error Messages s Option If the auto setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the auto setup procedure over again. Select settings for room EQ, mic, etc.
ENGLISH s Subwoofer Setup Select surround speakers use and size. [Selectable items] Manual Setup Large Small Select low range signal to be reproduced by subwoofer. None [Selectable items] Make detail settings for various parameters. [Selectable items] Speaker Setup MENU 2.Manual Setup 1spkr None ) ) NOTE By default, the AVR-2308CI’s “Amp Assign” setting is set to “ZONE2”. To use as the surround back speaker for the main zone, change the “Amp Assign” setting (vpage 30).
ENGLISH Getting Started Distance measurement Select the speaker you want to set, then set the distance. Set the value closest to the measured distance. [Variable range] Connections 0.0ft ~ 60.0ft : Display when “Feet” is set. 0.00m ~ 18.00m : Display when “Meters” is set. NOTE Setup Set the distance between the listening position and the various speakers to no more than 20.0 ft (6.00 meters). Playback Adjust channel levels to obtain equal volume from all speakers.
ENGLISH Select HDMI video output device. i/p Scaler [Selectable items] This sets the aspect ratio when outputting 480i/576i or 480p/576p input signals from the HDMI output connector. [Selectable items] FULL : Output at 16:9 aspect ratio. NORMAL : Output at 4:3 aspect ratio. A to H : Use i/p scaler function for analog video signal. : Do not use i/p scaler function. Make settings for resolution of HDMI video output signal.
ENGLISH Getting Started Front Select front speaker size. [Selectable items] Large d Dolby Digital Setup g Manual EQ Set dynamic range for downmix playback of Dolby Digital sources. Adjust tonal quality for each speaker using graphic equalizer. [Selectable items] Small : Select front speaker size. Connections Subwoofer Select subwoofer use. ON : Compression is used. Select this if sound from front speakers is distorted. OFF : Do not use compression. This is the recommended setting.
ENGLISH f Power On Level Option Setup Make various other settings. F Menu screen F Define the volume setting that is active when the power is turned on. Make settings for audio playback in a ZONE2 system. 2.Manual Setup 2-4.Zone2 Setup Level Lch : 0dB Rch : 0dB Vol.Limit : OFF Power On Lev.: Last Mute Lev. : Full Last : Use the memorized setting from the last session. ––– : Always use the muting on condition when power is turned on. F Menu screen F 2.Manual Setup 1.Speaker Setup 2.HDMI Setup 3.
ENGLISH Getting Started s Volume Control d Source Delete Set the main zone volume setting. Remove input sources that are not used from the display. [Selectable items] Volume Limit Connections Make a setting for maximum volume. [Selectable items] OFF : Do not set a maximum volume. Setup –20dB : Set the maximum volume to –20 dB. –10dB : Set the maximum volume to –10 dB. Playback 0dB : Set the maximum volume to 0 dB.
ENGLISH j Remote ID Setup l Display Change the Quick Select name. Up to 16 characters can be input. Set remote control ID. Adjust display brightness of the receiver. h Trigger Out 4 NOTE When using the AVR-2308CI with only the included remote control unit (RC-1080), there is no need to make settings. When using a separately sold remote control unit (RC-7000CI, etc.), this function can be used. Match the ID setting of the remote control unit and the receiver.
ENGLISH Getting Started n CD, AUX, DVD/HDP, TV/CBL, VCR, DVR, V.AUX This menu is for “CD”, “AUX”, “DVD/HDP”, “TV/CBL”, “VCR”, “DVR”, “V.AUX”. Input Setup F Menu screen F Connections Auto Preset 3.Input Setup CD Use this procedure to select the input source and make the settings related to playing input sources. n TUNER (AM/FM) Settings Related to Playing Input Sources Use the auto preset function to program radio stations. 1.Assign 2.Input Mode 3.Rename 4.
ENGLISH Make input mode and decode mode settings for this source. The selectable input modes depend on the input source and “Assign” setting (vpage 34, 35). Set the input mode for this source. [Input source] TUNER Operating from the main unit or main remote control unit PHONO EXT. IN : Play only signals from EXT. IN input. [Selectable items] Auto : Automatically detect input signal and perform playback. EXT. IN : Play only signals from EXT. IN input.
ENGLISH Getting Started Digital In Input source DVD/HDP TV/CBL VCR DVR V.AUX 1-RCA 2-RCA None 3-RCA None Select digital input connector to assign to this source. CD AUX [Input source] DVD/HDP Make settings for shuffle mode. TV/CBL VCR DVR Default setting Connections This cannot be set for input sources for which “iPod dock” is assigned. [Selectable items] Setup Playback Remote Control : Assign COAXIAL 1 input connector. iPod dock COAX2 : Assign COAXIAL 2 input connector.
ENGLISH Automatically convert video input signal to monitor output format. [Input source] DVD/HDP TV/CBL VCR DVR V.AUX [Selectable items] : Enable conversion. OFF : Disable conversion. Playing Multi-channel Sources (Dolby Digital, DTS, etc.) Standard Playback Source Level –12dB ~ 0dB ~ +12dB Surround Playback of 2-channel Sources To select these surround modes using the buttons on the main remote control unit, press the STD button. The mode switches each time the button is pressed.
ENGLISH Getting Started DSP Simulation Playback [Selectable items] 7CH STEREO Setup : This mode is for enjoying stereo sound from all speakers. ROCK ARENA : This mode is for enjoying the atmosphere of a live concert in an arena. JAZZ CLUB : This mode is for enjoying the atmosphere of a live concert in a jazz club. Playback Connections The desired mode according to the program source and viewing situation can be selected from among 7 DENON original surround modes.
ENGLISH PANORAMA Soften the treble understanding. Parameter range of movie soundtracks for better [Selectable items] 4.Parameter ON : CINEMA EQ is used. OFF : CINEMA EQ is not used. DIMENSION Shift sound image center to front or rear, to adjust playback balance. D.COMP [Variable range] Compress dynamic range (difference between loud and soft sounds). [Selectable items] : Turn dynamic range compression off. LOW : Low setting. Adjust surround sound parameters.
ENGLISH Getting Started ROOM SIZE SB CH OUT (for Multi-channel sources) SB CH OUT (for 2-channel sources) Determine size of acoustic environment. Select playback mode for surround back channels. Determine whether to use surround back speakers. [Selectable items] [Selectable items] [Selectable items] small : Simulate acoustics of a small room. Connections med. s medium med. l Setup large : Simulate acoustics of a large room.
ENGLISH d Room EQ f RESTORER Adjust the tonal quality of the sound. Select room equalizer for current environment. This function restores compressed audio signals to how they were before compression and corrects the sense of volume of the bass to obtain richer playback sound. [Selectable items] Tone Defeat [Selectable items] : Playback without tone adjustment. OFF : Allow tone adjustment (treble, bass).
ENGLISH Getting Started g Night Mode Audio Input Signal Optimized setting for late-night listening. Shows information about audio input signals. Information [Selectable items] Connections OFF F Menu screen F 5.Information : Turn night mode off. LOW : Low setting. Status MID : Middle setting. Shows information about current settings. Setup HIGH : High setting. F Menu screen F Operating from the main remote control unit Playback Press the NIGHT button.
ENGLISH Auto Surround Mode Preset Station Shows information about HDMI input/output signals and monitor. Shows information about auto surround mode settings. The surround mode for which the last memory function was used for the different input signal types is displayed. Shows information about preset stations. F Menu screen F 5.Information 5-3.HDMI Signal Info. 5.Information F Menu screen F 5.Information 1.Status 2.Audio Input Signal 3.HDMI Information 4.Auto Surround Mode 5.Quick Select 6.
ENGLISH Getting Started SOURCE SELECT BAND SHIFT
ENGLISH Basic Operation Prepare the equipment. Use SOURCE SELECT to select the input source. Set [MODE SELECTOR 1] to “AUDIO” or “VIDEO”. Set [MODE SELECTOR 2] to the component you want to operate. Start playback. Basic Operation 3 4 Press BAND to select “FM” or “AM”. Set [MODE SELECTOR 1] to “AUDIO”. (vpage 50 “Remote Control Unit Operations”) A1 ~ A8 B1 ~ B8 520 / 600 / 1000 / 1400 / 1500 / 1710 kHz, 90.1 / 90.1 MHz C1 ~ C8 90.1 MHz D1 ~ D8 90.1 MHz E1 ~ E8 90.1 MHz F1 ~ F8 90.
ENGLISH Getting Started
ENGLISH Press STATUS until “SIGNAL” appears on the display. Adjust the position of the antenna until “SIGNAL: GOOD” is shown on the display. Press TUNING and select channel 0 (XM000). Use o p to select the category, then use ui to select the desired station. iPod® Playback The music on an iPod can be played by using the Control Dock for iPod (ASD-1R, ASD-3N or ASD-3W, sold separately).
ENGLISH Getting Started
ENGLISH “ZONE2 SOURCE” is shown on the display. ZONE2 SOURCE RECOUT XM ZONE2 TUNER ······ ···· RECOUT TUNER ZONE2 XM RECOUT SOURCE • The fader function does not affect the subwoofer. • The fader can be adjusted until the volume of the speaker adjusted to the lowest value is –12 dB. Convenient Functions Channel Level You can adjust the channel level either according to the playback sources or to suit your taste, as described below. 1 Press or [CH SELECT]. Channel Volume FL C FR SW 0.0dB 0.
ENGLISH Getting Started Quick Select Function Last Function Memory With this function, the currently playing input source, input mode, surround mode, room EQ settings and volume can be stored in the memory. This stores the settings as they were directly before the standby mode was set. When the power is turned back on, the settings are restored to as they were directly before the standby mode was set.
ENGLISH Remote Control Unit Operations [Front] Presetting [MAIN ON] [NUMBER] 1 Set [MODE SELECTOR 1] to “AUDIO” or “VIDEO”. 2 [MODE SELECTOR 2] 3 [ZONE2 OFF] [MAIN ON] 4 [NUMBER] Set registered. Press b Set to the AUDIO side for the CD or TAPE/CD-R/MD position, and to the VIDEO side for the DVD/VDP, SAT/CABLE, VCR or TV position. 2 3 Set [MODE SELECTOR 2] to the component you want to operate. Operate the component. b For details, refer to the component’s operating instructions.
ENGLISH Getting Started Functions of Buttons by Component n Front Connections [OFF] [SHIFT] Setup Playback Remote Control [1], [2], [3], [A/B], [0], [DISC SKIP +/ FAVORITE], [6 7], [8 9], [VCR CH+/–], [MODE SELECTOR 1] [ON/SOURCE] [CHANNEL+/–] Device operated MODE SELECTOR 1 MODE SELECTOR 2 OFF ON/SOURCE CD Recorder MD Recorder Tape Deck DVD Player CD – VIDEO TAPE / CD-R / MD – – DVD / VDP – Power off Power on Multi-Zone Information Troubleshooting – Power on / Standby – – – – – – S
ENGLISH Device operated MODE SELECTOR 1 MODE SELECTOR 2 Video disc MD Tape Deck DVD Player Recorder player AUDIO CD iPod/ NETWORK TAPE / CD-R / MD DVD / VDP – – – – – TUNING (+, –) / TV VOL (+, –) Tuning (+, –) Tuning (+, –) Tuning (+, –) Tuning (+, –) Tuning (+, –) MODE / DVD MENU Switch search modes Switch search modes Switch search modes Switch search modes – – AUDIO BAND / PICTURE ADJUST – AM / FM switching AM / FM switching AM / FM switching AM / FM switching AM / FM switchi
ENGLISH Getting Started Sub Remote Control Unit Punch Through Function [Front] “Punch Through” is a function allowing you to operate 1, 2, 3, 6, 7, 8 and 9 on CD, iPod/NETWORK, TAPE/CD-R/MD, DVD/VDP or VCR components when in the SAT/CABLE or TV mode. By default, nothing is set.
ENGLISH Amp Assign / Multi-zone Connections and Operations Main zone FL SW SL ZONE2 C FR 5.1ch SR + Z2L Amp Assign mode: Z2R ZONE2 (Default) Stereo Setup NOTE F Multi-zone playback • 5.1-channel playback + ZONE2 stereo playback • 5.
ENGLISH Getting Started Setting 2 : F 7.1-channel Setting 3 : With this setting it is possible to switch between the following two playback modes. playback F 5.1-channel playback F 2-channel playback Switching·················Surround Mode switching Main zone FL SW C FR Connections Main zone FL Amp Assign mode: 7.1ch SL SR 7.1ch Setup Playback Remote Control Speaker terminal Amp Assign mode Main zone FRONT CENTER R L FR FL C SURR.
ENGLISH F Making bi-amp connections for the FL and FR channels in the main zone and conducting 5.1-channel playback Multi-zone and Operations with Zone Output controlSettings unit Prepare pre-main amplifiers for ZONE2. Audio signals ZONE2 OUT Stereo Main zone (7.1-channel system) ZONE2 ZONE2 Main zone FL SW 5.
ENGLISH Getting Started SOURCE SELECT VOLUME Multi-zone Operations Adjusting the Volume GOperation on the main unitH Turning the Power On and Off Turn to adjust. GOperation on the remote control unitH Connections GOperation on the main unitH Press for the zone to be operated. When the power turns on, the multi-zone indicator ( the display.
ENGLISH We recommend installing the speakers for the surround “L” and “R” channels a bit forward. Path of the surround sound from the speakers to the listening position We recommend using 2 speakers. When using dipolar speakers in particular, be sure to use 2 speakers. Other Information About Speaker Installation Surround back speakers 48 $ '3 Below we introduce examples of speaker layouts. Refer to these to arrange your speakers according to their type and how you want to use them.
ENGLISH Getting Started G2H When not using surround back speakers Front speakers Center speaker Connections Monitor Subwoofer 60° Surround speaker Setup Front speaker 2 to 3 feet / 60 to 90 cm Playback 120° Surround speakers Remote Control GAs seen from aboveH GAs seen from the sideH Surround Multi-Zone The AVR-2308CI is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.
ENGLISH HDMI is a digital interface standard for next generation TVs based on DVI (Digital Visual Interface) standards and optimized for use in consumer equipment. Non-compressed digital video and multi-channel audio signals are transmitted with a single connection. HDMI is also compatible with HDCP (High-bandwidth Digital Contents Protection), a technology for protecting copyrights that encrypts digital video signals in the same was as with DVI.
ENGLISH Getting Started Surround Modes and Parameters Signals and adjustability in the different modes Channel output Surround mode Front L/R Center Surround L/R Parameter (default values are shown in parentheses) Connections Surround Back L/R Subwoofer D. COMP LFE z1 AFDM z2 z1 SB CH OUT CINEMA EQ.
ENGLISH Getting Started Signals and adjustability in the different modes Parameter (default values are shown in parentheses) Surround mode PRO LOGIC g/gx MUSIC mode only NEO:6 MUSIC mode only EXT.
ENGLISH Getting Started Differences in Surround Mode Names Depending on the Input Signals Input signals Button DTS Note Surround mode Connections ANALOG LINEAR PCM DTS ES DSCRT (With Flag) DOLBY DIGITAL DTS ES MTRX (With Flag) DTS (5.1ch) DTS 96/24 DOLBY DIGITAL EX (With Flag) DOLBY DIGITAL EX (With no Flag) DVD-AUDIO DOLBY DIGITAL (5.1/5/4ch) DOLBY DIGITAL (4/3ch) DOLBY DIGITAL (2ch) DVD-Audio (multi ch) DVD-Audio (2ch) STANDARD DTS SURROUND Setup Playback DTS ES DSCRT6.
ENGLISH DTS DOLBY DIGITAL DVD-AUDIO ANALOG LINEAR PCM DTS ES DSCRT (With Flag) DTS ES MTRX (With Flag) DTS (5.1ch) DTS 96/24 DOLBY DIGITAL EX (With Flag) DOLBY DIGITAL EX (With no Flag) DIRECT S S S S S S S S S S MULTI CH DIRECT A A A A A A A A A A Surround mode Note DOLBY DIGITAL (5.
ENGLISH Getting Started Relationship Between Video Signals and Monitor Output Video convert Connections Setup Playback ON Remote Control Multi-Zone HDMI A A A A A A A A A A A A A A A A S S S S S S S S S S S S S Input signals COMPONENT A A A A S (1080p) S (480p ~ 720p) S (480i / 576i) S (1080p) S (480p ~ 720p) S (480i / 576i) S (1080p) S (480p ~ 720p) S (480i / 576i) S (1080p) S (480p ~ 720p) S (480i / 576i) A A A A S (Other than 480i / 576i) S (480i / 576i) S (1080p) S (480p ~ 720p) S (480i / 576i) S
ENGLISH MONITOR OUT HDMI COMPONENT S-VIDEO VIDEO A A A A VIDEO A A A S-VIDEO A A A S-VIDEO VIDEOz2 A A — VIDEO A A COMPONENT A A A COMPONENTz1 VIDEO A A COMPONENTz2 S-VIDEO A A COMPONENTz2 S-VIDEO VIDEOz2 A COMPONENTz1 — VIDEO A HDMI A A A HDMI VIDEO A A HDMI S-VIDEO A A HDMI S-VIDEO VIDEOz2 A HDMI — VIDEO A HDMI COMPONENT A A z HDMI COMPONENT 1 VIDEO A z HDMI COMPONENT 2 S-VIDEO A HDMI COMPONENTz2 S-VIDEO VIDEOz2 z HDMI COMPONENT 1 — VIDEO A : Not output z1 : On-screen display superimposed on video signal
ENGLISH Getting Started Symptom Power turns off suddenly and power indicator flashes red. Troubleshooting Connections Setup If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other components operating properly? If this unit does not operate properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
ENGLISH 37 Cause Countermeasure • The “Manual Setup” – “HDMI • Set to “TV”. Setup” – “HDMI Audio Setup” – “HDMI Audio Out” setting is set to “AMP”. Page 27 GVideoH • Set to something other than “None”. • Select a surround playback mode. • Turn on the subwoofer’s power. 26 • Set to “Yes”. 26 • Check the connections. 9 • Adjust the subwoofer’s volume to an appropriate level. • Set to the STANDARD mode. 48 Symptom No picture appears. 37 – 36 Picture cannot be recorded.
ENGLISH Getting Started GiPodH Symptom iPod cannot be played. Cause Countermeasure Connections • The input source assigned to • Switch to the input source “iPod dock” is not selected. assigned at “iPod dock”. • Cable is not properly connected. • Reconnect. • Control Dock for iPod’s AC • Plug the Control Dock for iPod’s adapter is not connected to AC adapter into a power outlet. power outlet.
ENGLISH Getting Started Specifications [FM] (note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15 W) 87.5 MHz ~ 107.9 MHz 1.0 µV (11.2 dBf) MONO 1.6 µV (15.3 dBf) STEREO 23 µV (38.5 dBf) MONO 77 dB STEREO 72 dB MONO 0.15 % STEREO 0.
List of preset codes / Liste de codes préréglés DVD Player A D H J K M P S T Z Aiwa Denon Hitachi JVC Konka Magnavox Mitsubishi Panasonic Philips Pioneer Sanyo Sony Toshiba Zenith Curtis Mathes 009 014, [111]z 010 006, 011 012, 013 005 004 014 005, 015, 016, 017 003, 008 018 002, 019, 020 001, 021, 022 023 Cybernex D E P R S Denon Magnavox Mitsubishi Panasonic Philips Pioneer RCA Sony 028, 029, 112 026 028 029, 030 026 028, 031 032 033, 034, 035, 036 Daytron DBX Dumont Dynatech Electrohome Electro
Midland Minutz Mitsubishi N Montgomery Ward Motorola MTC NAD National National Quenties NEC O P Nikko NTC Optimus Optonica Orion Panasonic Philco Philips Q R Pioneer Portland Price Club Proscan Proton Pulsar Quasar Radio Shack RCA S Realistic Saisho Samsung Sansui Sanyo SBR Schneider Scott Sears Sharp Siemens Signature Simpson Sony Soundesign Spectricon 001, 039, 048, 056, 057, 058, 065, 081, 083 125 066 001, 016, 039, 048, 056, 057, 058, 065, 081, 082, 083, 105 011, 020, 144, 145, 146 121, 147 03
www.denon.com Denon Brand Company, D&M Holdings Inc.