PR-450UDM Contactless IC Card Reader/Writer User’s Manual
* Microsoft® and Windows® are trademarks or registered trademarks of Microsoft Corporation in the U.S.A. and other countries. * FeliCa is a registered trademark of Sony Corporation. FeliCa is a contactless IC card technology developed by Sony Corporation. * MIFARE® is a registered trademark of NXP Semiconductors.
Federal Communication Commission Interference Statement NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Declaration of Conformity (For European Union) English: Here by, DENSO WAVE INCORPORATED declare that this equipment (Contactless IC Card Reader / Writer), model PR-450UDM is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Česky: DENSO WAVE INCORPORATED tímto prohlašuje, že tento PR-450UDM je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Latviski: Ar šo DENSO WAVE INCORPORATED deklarē, ka PR-450UDM atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių: Šiuo DENSO WAVE INCORPORATED deklaruoja, kad šis PR-450UDM atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands: Hierbij verklaart DENSO WAVE INCORPORATED dat het toestel PR-450UDM in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Suomi: DENSO WAVE INCORPORATED vakuuttaa täten että PR-450UDM tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska: Härmed intygar DENSO WAVE INCORPORATED att denna PR-450UDM står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
SAFETY PRECAUTIONS Be sure to observe all these safety precautions. ■ Please READ through these instructions carefully. They will enable you to use the PR-450UDM correctly. ■ Always keep this manual handy for easy reference. Strict observance of these warming and caution indications is a MUST for preventing accidents which could result in bodily injury or substantial property damage.
WARNING Alerts you the conditions which could cause serious bodily injury or death if you do not follow the instruction. To System Designers: When introducing the PR-450UDM IC card reader/writer in those systems that could affect human lives (e.g., medicines management system), develop applications carefully through redundancy and safety design which avoid the feasibility of affecting human lives even if a data error occurs.
Replace the cable with a new one if it gets damaged (exposed or broken lead wires, etc.). Failure to do so could cause fire or electrical shock. If foreign material or water gets into the PR-450UDM, immediately turn off the power and unplug the cable from the device. Failure to do so could cause fire or electrical shock. If smoke, abnormal orders or noises come from the PR-450UDM, immediately turn off the power, unplug the cable from the device, and contact your nearest dealer.
CAUTION Alerts you the conditions which could cause minor bodily injury or substantial property damage if you do not follow the instruction. Operating Environments: Do not put the PR-450UDM in places where there are excessively high temperatures, such as inside closed-up automobiles, or in places exposed to direct sunlight. Doing so could affect the housing or parts, resulting in fire. Avoid using the PR-450UDM in extremely humid or dusty areas, or where there are drastic temperature changes.
Preface The PR-450UDM reader/writer, which is easy to plug in to your host computer with a USB cable, is an IC card reader/writer capable of reading contactless IC cards. This user’s manual sets forth the procedures for handling, setting and operating this product. You should study it carefully to make sure that you use this product both correctly and effectively before starting the operation. About This Document ● All rights in this document are reserved by DENSO WAVE INCORPORATED.
Applicable Standards & Laws ● This product is classified as inductive reader/writer communications equipment under the High Frequency Equipment section of Japan’s Radio Law. It has a built-in reader/writer unit certified by the Ministry of Internal Affaires and Communications as the AC-06104 model type unit. ● This product, when not using radio frequencies, is classified as Class B information technology equipment in accordance with the Voluntary Control Council for Interference Technology Equipment (VCCI).
Part Names IC card reader panel USB connector Cradle LED LED indicator Light ON Fast blinking Slow blinking Light OFF State Communication standby Communication underway Malfunction or abnormality detected Main unit powered off :* The LED is normally configured in this factory default setting. If not so, the LED condition may have been possibly changed by the application software. Consult your system administrator.
Before Starting the PR-450UDM Preparation You should first go through the following procedure before starting the PR-450UDM setup. ➊ Cancel the computer’s power supply control setting. This reader/writer does not support such power supply control functions as “standby”, “sleep”, “resume” and “hibernation”. You need to turn off these functions before starting the setup procedure. ➋ Login the computer with the administrator’s right.
Notes for placing the PR-450UDM Do not place the PR-450UDM on a metal plate Do not place the PR-450UDM on a steel desk or computer with a metal housing. It will generate harmful interference due to the effects of metal, which may block wireless networking with IC cards. Leave enough space between the PR-450UDMs When operating more than one PR-450UDM, be sure to place them apart from each other as shown in the figures below. This is to avoid radio frequency interference between the PR-450UDMs.
Setting Up the PR-450UDM 1. Connecting to your computer Connect the PR-450UDM to the USB port on your computer or to the USB powered hub through the USB cable provided in the package. Important! Leave at least 10 msec intervals when connecting and disconnecting the USB cable. ➋ If this time interval is short, the USB device may not be correctly identified. Connect the PR-450UDM directly to the USB port on your computer via USB cable. ➊ Set the PR-450UDM in the attached cradle.
2. Installing the driver Soon after the PR-450UDM is connected to the host computer, Found New Hardware Wizard starts. Install the driver in the following steps. Installing on WindowsXP ➊ ➋ ① ② ③ ④ Select ① Search for the new driver in these locations (S) and the ② Include this location in the search (0) check box. Click ③ Reference (R) and select the folder of the driver you have downloaded in “Before Starting the PR-450UDM” in page 4. Then click ④ Next.
WindowsXP ➎ ➏ Check that the driver is now properly installed. ① ② If DENSO WAVE USB-SER Comm.Port is added to the sub-tree of Ports (COM & LPT) as shown above, the driver is successfully installed. On the control panel, click System -> System Properties -> ① Hardware tab -> ② Device Manager tab. The Device Manager screen is displayed. If DENSO WAVE USB-SER Comm.
Installing on Windows2000 ➊ ➋ ① ② Select ① Search for the best driver for your device (Recommended) (S), then click ② Next. Click Next. ➌ ➍ ① ② Check ① Specify a location (S) check box and select the folder of the driver you have downloaded in “Before Starting the PR-450UDM” in page 4. Then click ② Next. When “New hardware device driver found” messages appear, click Next.
Windows2000 ➎ ➏ Make sure that the driver is correctly installed. ① ② If the Completion screen appears at the end of driver installation, click Finish. On the control panel, click System -> System Properties -> ① Hardware tab -> ② Device Manager tab. The Device Manager screen is displayed. ➐ If DENSO WAVE USB-SER Comm.
Uninstalling the driver Preparation ➊ Login your computer with the administrator’s right. In WindowsXP/2000, removing the driver requires the administrator’s right. ➋ Release the PR-450UDM from your computer. How to remove You can remove the driver with the dedicated uninstaller Pcd_SerRemover in the steps below. This example shows the display screens for WindowsXP. ➋ ➊ Double-click the uninstaller’s Pcd_SerRemover icon. The USB-SER Driver Remover screen appears. Click OK.
Updating the driver Preparation ➊ Login the computer with the administrator’s right. In Windows XP/2000, removing the driver requires the administrator’s right. ➋ Download the latest version of the USB driver. The latest version of the USB driver is available from our website at http://www.denso-wave.com. Download the driver following the steps below. The file downloaded is a self-extracting file, containing a driver and an uninstaller in compressed form.
Handling of Card Notes to users Do not unplug the USB cable from the PR-450UDM while the application is still running. This may cause the host computer to become unstable or the data stored in the PR-450UDM will be lost or broken. Proper card position You MUST place the card sideways as shown in the figure below. Be sure to place only one card in the cradle. The PR-450UDM cannot read more than one card at a time.
Specifications ● Standard Item Specification Operating environment Office environment Supported card type MIFARE (Standard 1k, 4k) ISO/IEC 14443 Type A (Incl. MIFARE DESFire) ISO/IEC 14443 Type B FeliCa Interface Complying with USB 1.1 (Power is supplied via USB interface) Supported OS WindowsXP, Windows2000 Power voltage & source 5 VDC/500 mA max. Outer dimensions 75 (width) X 54 (height) X 10 (depth) mm (Excl.
Outer dimensions All the measurements given in the figures are provided as referential values.
Troubleshooting If there is a problem in IC card reading, you are advised to take the following troubleshooting measures before consulting your dealer. Problem The LED does not light up. • Make sure that the USB cable is properly connected to the PR-450UDM. • Remove the USB cable, then reconnect it to the PR-450UDM again. • Replace the USB cable with a new one. The PR-450UDM is assumed to be broken if the problem cannot be solved even with these measures. If such is a case, contact your dealer.
Problem Communication with IC card is blocked. • Check that the card is correctly placed in the cradle. (Refer to “Handling of Card” in page 13.) • Make sure that the card you are using is supported as a readable card. (Refer to “Specifications” in page 14.) • Check that the PR-450UDM is free from any noise source that may adversely affect its operation. If required, you should take some appropriate noise prevention measures. (Refer to “Notes for placing the PR-450UDM” in page 5.
Contactless IC Card Reader/Writer PR-450UDM User’s Manual Second Edition, August 2007 DENSO WAVE INCORPORATED Toranomon 4-Chome MT Bld. II, 4-2-12 Toranomon, Minato-ku, Tokyo, 105-0001 http://www.denso-wave.
