User Manual

1. TWEETER X 2
2. FUNCTION/STANDBY
BUTTON
3. P-MODE/M./ECHO BUTTON
4. 10/M./FOLD.- BUTTON
5. /TUN.- BUTTON
6. VOL.- BUTTON
7. /TUN.+ BUTTON
8. VOL.+ BUTTON
9. /PAIR/SCAN BUTTON
10. 10/M./FOLD.+ BUTTON
11. EQ/LIGHT BUTTON
12. PARI INDICATOR
13. CHARGE INDICATOR
14. LCD DISPLAY
15. SPEAKER X 2
16. HANDLE
17. MIC VOL. KNOB
18. 6.3mm MIC JACK 1
19. 6.3mm MIC JACK 2
20. LIGHT BAR
21. 3.5mm AUX IN JACK
22. USB PORT
23. POWER ON/OFF BUTTON
24. VENTILATION HOLES
25. AC SOCKET
26. Antenna
Getting Started
POWER SOURCE
This unit works with rechargeable lead-acid battery (the battery capacity 4000mAh). Fully charge the unit (around 7 hours) before using the product for the
first time. The playback time has about 2 hours after full charging. Unplug the AC Power cord from the AC socket to work on the battery pack after fully
charged. Plugging the AC Power cord while the battery pack is attached initiates the charging of this battery, the charge LED indicator lights red during
charging, when the battery is fully charged the indicator will turn to green. When the unit is with low battery, the LED indicator will flash in red.
Warning: Do not change the battery, only high-qualified personnel can perform this operation.
OPERATION INSTRUCTION
BASIC FUNCTION
TURNING THE UNIT ON/OFF
Press the power ON/OFF button on the rear cabinet to switch the unit on or off.
NOTE: In USB/Bluetooth/AUX mode, when the unit is not providing the main function for around 15 minutes, the unit will automatically switch into standby
mode. Press the FUNCTION/ button to turn on the unit again.
Please note that low volume setting in the audio source may be recognized as “no audio signal”, this will affect the capability of signal detection from the
device and can also originate an automatic switch into standby mode. If this happens please reactivate the audio signal transmission or increase the
volume setting on the audio source player in order to resume playback.
Electrostatic Discharge hints – The unit may reset or may not reset to normal operation mode due to electrostatic discharge, just switch it off and
reconnect again.
SETTING THE FUNCTION MODE
To change the function modes, press the FUNCTION/ button repeatedly to choose USB/AUX/BLUETOOTH/RADIO function.
ADJUSTING THE VOLUME
1. Press the VOL.+ or VOL.- button to increase or decrease the music volume.
2. Rotate the MIC VOL. knob on the unit to increase or decrease the microphone volume.
EQUALIZER (EQ) FUNCTION
This unit has a built-in equalizer system, press the EQ/LIGHT button on unit to select a setting that best matches the music style: FLAT, POP, CLASSIC,
JAZZ, and ROCK.
MICROPHONE ECHO ADJUSTMENT
Press and hold the P-MODE/M./ECHO button on unit to turn on or turn off the microphone echo effect. When the echo effect is on, the display will show
“ECHO”.
FLASHING LIGHT
There are 5 modes for the DISCO LED lighting above the speakers. Press and hold the EQ/LIGHT button to choose the desired light mode. To turn off the
light effect, press and hold the EQ/LIGHT button until OFF shows on the display.
L-1: Blue LED will be on constantly when it is selected.
L-2: Blue LED will be on flashing mode.
L-3: Red LED will be on constantly.
L-4: Red LED will be on flashing mode.
L-5: 7 colors LED will be on flashing mode.
There’s a light bar above the handle, the white light on when the Blue/Red LED on constantly, the bar will keep flashing when LED in flashing mode. Press
and hold the EQ/LIGHT button until OFF shows on the display to turn it off together with the disco light.
2