User Manual

ANC ON/OFF
USB SLOT
3,5 MM AUX
MIC
VOLUME+
NEXT SONG
VOLUME-
PREVIOUS SONG
MFB (POWER ON/OFF,MAKE/END
PHONE CALL, PLAY/PAUSE,LED)
Congratulations on your purchase and thank you for your use of our Bluetooth Active
Noise Cancelling Headset. In order to start quickly, please read the user guide
carefully.
Caution
1. Please turn off the headset and put it into box to avoid damage, scratches or
bracket deformation when long time no use. In order to prolong the battery service life,
please charge every 6 months.
2. Please charge at first if the headset is left unused for long time.
3. The battery of headset is original and please don’t change it by yourself.
4. Please keep the headset under dry place.
5. Please don’t put this product into the environment with temperature over than 60
or into fire to avoid battery blast accident.
6. Please don’t bent or twist the bracket to avoid deformation.
7. Please don’t tear down ear-cushions by un-professional person.
8. Don’t adjust the volume to a very high level and continued play. If tinnitus occurs,
please turn the volume down or stop playing, do not turn the volume up suddenly.
Please slowly turn up the volume to avoid hearing damage caused by high volume.
9. Do not use the headset in dangerous place or place where cannot hear the outside
sound.
Included:
The headset contains the following parts:
Bluetooth Active Noise Cancelling Headset X 1
Manual X 1
3.5mm – 3.5mm audio Cable X 1
Micro USB Charging Cable X 1
Charge the Battery:
The headset contains a Micro USB cable that can be connected to your computer or
2
other device made for USB charging. Plug the Micro USB end of the included USB
cable into the USB micro port charger connector under the left ear-cap of the
headphone. Plug the other end into a USB port on your computer or other devices
made for USB charging. The indicator light will be red while charging. Once fully
charged, the indicator light will turn off. Charge time is about 3 hours on an empty
battery.
Active Noise Cancelling On:
Hold the ANC button for 1 second. Green LED light will turn on. The ANC function is
available at both Wired and Wireless condition.
Active Noise Cancelling Off:
Hold the ANC button for 1 second. Green LED light will turn off. The ANC function
must be switched off by manual operation.
Bluetooth Switch On:
To switch on, press and hold the MFB about 3 seconds. The headset enters Bluetooth
searching mode. Blue light on.
Bluetooth Switch Off:
To switch off, press and hold the MFB about 3 seconds.
Pairing:
1. Ensure that your phone or Bluetooth device is switched on.
2. To pair the headset if it has not been previously paired with a device, switch on the
headset. The headset enters the pairing mode, and the blue indicator light starts to
flash quickly. To pair the headset if it has been previously paired with another device,
ensure that the previously paired devise is switched off.
3. Activate the Bluetooth feature on your phone or Bluetooth devices, and set it to
search for Bluetooth devices.
4. Select “Denver BTN-206” from the list of found devices on your phone or Bluetooth
devices.
5. When successfully connected, the blue light turns to continuously lighting.
The headset that has been previously paired with another device will automatically
connect with the device if the device is power on and within connecting range, if not,
the headset will enter standby mode with continuously blue light.
Adjust the volume:
Turn the volume up or down by a long press on the volume +/- key during a call or
while listening to music. When the volume reaches to Maximum volume, there is a
warning tone.
Application:
Denver BTN-206 can make and receive calls hands-free with your compatible mobile
phone and listen to music from a compatible Bluetooth device, but they should be with
10 meters (33 feet) of each other.
ENG

Summary of content (4 pages)