User Manual

ManualsBrandsDenver ManualsOffice FurnitureCRP-618

ENGLISH

FUNCTION AND CONTROLS

1. PROJECTION ON/OFF

2. PROJECTION TIME 180°

3. SNOOZE / SLEEP / DIMMER /DST

4. ON – OFF RADIO / ALARM OFF

5. DISPLAY

6. ALARM 2 INDICATOR

7. PM INDICATOR

8. STANDBY INDICATOR

9. ALARM 1 INDICATOR

10. MEMORY/MEMORY+/ CLK.ADJ./NAP

11. << / TUNE - / YEAR/MONTH/DAY/ DISPLAY AUTO CHANGE ON-

OFF

12. >> / TUNE + / AUTO ON-OFF DISPLAY

13. VOLUME DOWN/ ALARM 1 ON-OFF SET

14. VOLUME UP/ ALARM 2 ON-OFF SET

15. SPEAKER

16. FOCUS ADJUSTMENT FOR PROJECTION UNIT

17. FM ANTENNA

18. BATTERY COMPARTMENT

19. AC POWER CORD

20. RATING LABEL (BOTTOM OF UNIT)

17 18 19 20

ENG-1

DENVER CRP-618

Summary of content (8 pages)

PAGE 1
DENVER CRP-618 ENGLISH 15 16 14 17 18 19 20 FUNCTION AND CONTROLS 1. PROJECTION ON/OFF 2. PROJECTION TIME 180° 3. SNOOZE / SLEEP / DIMMER /DST 4. ON – OFF RADIO / ALARM OFF 5. DISPLAY 6. ALARM 2 INDICATOR 7. PM INDICATOR 8. STANDBY INDICATOR 9. ALARM 1 INDICATOR 10. MEMORY/MEMORY+/ CLK.ADJ./NAP 11. << / TUNE - / YEAR/MONTH/DAY/ DISPLAY AUTO CHANGE ONOFF 12. >> / TUNE + / AUTO ON-OFF DISPLAY 13. VOLUME DOWN/ ALARM 1 ON-OFF SET 14. VOLUME UP/ ALARM 2 ON-OFF SET 15. SPEAKER 16.
PAGE 2
Power connection Plug the AC power cord to a household outlet AC source. This unit is equipped with a battery backup system, it requires a 3V CR2032 flat lithium battery (not included). Insert the battery in the battery compartment, making certain that the positive and negative (+ and -) battery terminals are attached to the corresponding terminals on the plate in the battery compartment.
PAGE 3
Select alarm weekday mode as follows 1-5 : Monday to Friday 1-7 : Whole week 6-7 : Saturday & Sunday 1-1 : One day of week Action (during data adjustment) : - Press << / Tune - button (11) to adjust data backward. - Press >> / Tune + button (12) to adjust data forward. - Keep depress << or >> button for 2 seconds to enable auto forward. Enable / disable the Alarm Press and hold the “ALARM 1” (13) / “ALARM 2” (14) button to enable or disable the alarm.
PAGE 4
Auto change display content: In radio off mode, press & hold the DISPLAY AUTO CHANGE ON/ OFF button (11) for 3 seconds to enter time display auto change mode. to display the Year and press again to display Month/Day, the display returns to time display after 5 seconds. YEAR Indicator MONTH Indicator DAY Indicator Listening to Radio Press the ON/OFF button (4) to turn the unit on. Use the Tune + or Tune – button to select the desired radio station.
PAGE 5
Sleep operation When listening to radio, press Sleep button (3) to enter sleep mode. You can just adjust the sleep timer from 90 mins to 15 mins by pressing the Sleep button (3). The unit will automatically turn off after the selected time. Dimmer control In standby mode, press the DIMMER (3) button allows you to set the brightness of the LED display to high, medium ,low 3 levels. 1. The clock display with dimmer low is the default setting. 2.
PAGE 6
NOTE : PROJECTS TIME IMAGE ON THE CEILING OR WALL OF A DARKENED ROOM. MAXIMUN PROJECTION DISTANCE IS 3-9 FEET. Specifications - Frequency range : 87.5 – 108MHz - Battery backup : 3V (CR2032 Flat Lithium battery x 1) not included - Power supply : AC230V ~ 50Hz Resetting If the system does not respond or exhibits erratic or intermittent operation, you may have experienced an electrostatic discharge (ESD) or a power surge that triggered the internal microcontroller to shut down automatically.
PAGE 7
11. Attention should be drawn to the environmental aspects of battery disposal. 12. Do not dispose this product into usual household garbage at the end of its lifecycle; hand it over to a collection center for recycling the electrical and electronic appliances. By recycling, some of the materials can be reused. You are making an important contribution to protect our environment. Please inquire your community administration for the authorized disposal center.
PAGE 8
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S www.denver-electronics.com Electric and electronic equipment contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment) is not handled correctly. Electric and electronic equipment is marked with the crossed out trash can symbol, seen above.