HIGH Definition Digital Receiver DMB-112HD DVB-T PLAYER
FAQ – DENVER DMB-112HD Congratulations with your new DVB-T tuner. With this settop box you can enjoy digital TV signal, and get HD channels in super quality. To get the good signal, it takes a proper antenna, and good cables with proper plugs and assembling. If you don’t have this, it can give bad receival of channels. Active antenna: DENVER DMB-112HD can give 5V to an active antenna. Ifyou want to use this you have to turn it on in the setup menu.
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings, install in accordance with the instructions. 8) Do not install near any heat sources such as radiations, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized plug.
Safety Instructions Always read the safety instructions carefully Keep this Instruction Manual for future reference Keep this device away from humidity Lay this device on a reliable flat surface before setting it up Do not stand it on soft furnishings The power cable/disconnect device shall remain easy to operate/disconnect.
Front Panel 1 2 3 4 5 1. CHANNEL DOWN: Used to change channels without using the Remote Control. 2.POWER BUTTON: Push to turn on/off the main power supply. 3.CHANNEL UP : Used to change channels without using the Remote Control. 4.REMOTE CONTROL SENSOR: Used to receive the signal from the Remote Control. 5.USB: For software upgrade and media playback. Rear Panel 5 1 2 3 6 4 7 1.RF IN: This socket connects to your external Aerial 2.
Remote Control Instruction POWER: turn on or off the receiver <0>-<9>: Numeric keys. CH-/CH+: Program changing keys. MENU: Display main menu on TV screen, and press again to disappear menu. OK: To confirm current setting, or display all programs in no-menu mode. VOL-/ VOL+: adjust the volume. : Press to move the cursor EPG: Shows the Electronic Program Guide. FAV: Displays your favorite channels list. Press FAV again to access to the other favorite lists. V-FORMAT:Switch the HDMI 720P and 1080i.
Installing the Batteries Remove the battery cover from the Remote Control and put 2xAAA size batteries inside the compartment. The diagram inside the Battery Compartment shows the correct way to install the batteries. 1.Open the cover O PE 2.Install batteries N 3.Close the cover CL O SE Using the Remote Control To use the Remote Control, point it towards the front of the Digital Set Top Box.The Remote Control has a range of up to 7 metres from the Set Top Box at an angle of up to 60 degrees.
First Time Installation After all connections have been made properly, switch on TV and make sure the unit is connected to the Main Power. Press Power button to switch the unit on. If you are using the unit for the first time or have restored the unit to Factory Default, the Installation Guide Menu will appear on yourTV screen. Installation Guide OSD Language English Country Australia Channel Search Exit Exit OK Confirm (1) [OSD Language] press / key to select a language.
(a) Program Edit To edit your program preferences (lock, skip, fav, move delete or rename), you will need to enter the Program Edit Menu. This Menu requires a password to access. Enter the default password '0000'.
2. Press / to move the channel. 3. Press OK to confirm. 4. Repeat the above steps to move more channels. Lock Program You can lock selected programs for restricted viewing. Lock a TV or Radio channel: 1.Select the preferred channel then press the YELLOW button. A lock-shaped symbol is displayed. The channel is now marked as locked. 2. Repeat the previous step to select more channels. 3. To confirm your settings and exit the menu, press the EXIT button. 4.
(2). Picture Setting To access the Menu，press MENU then select [Picture] using the / key. The Menu provides options to adjust the video settings. Press / to select an option and press / to adjust that setting.Press EXIT to exit the menu. Picture Aspect Ratio Resolution TV Format Video Output EXIT Return 16:9 Wide Screen 1080i PAL CVBS OK Confirm (a) Resolution You can change this setting if the picture resolution does not appear to be correct. This setting is to match the most common setting for HDMI.
(3). Channel Search To access the menu, press MENU and select [Search Channel] using the / keys. This Menu provides options to adjust the Search Channel settings. Press / to select an option and press / to adjust the settings. Press EXIT to exit the Menu Channel Search Auto Search Manual Search Country Antenna Power EXIT Return France Off Confirm OK (a) Auto Search This option will automatically search for channels and save them once the scanning is complete.
/ key to select the channel frequency. 2. Press the 3. Press OK to start searching channels. If a channel is found, it is saved and added to the channels list. If channels can not be found during searching, the unit will exit automatically. (c) Country Select your country of residence (d) Antenna Power Enable Antenna Power if an external active antenna is connected. (4).Time Setting To access the Menu, press MENU then select [Time] using the / provides options to adjust the time settings.
(5). Option To access the Menu, press MENU and select [Option] using the / keys. The menu provides options to adjust the OSD Language,Subtitle Language and Audio Language. Select an option and press / to adjust thesetting. Press EXITto exit the Menu. (a)OSD (On Screen Display) Language Select an OSD language. (b) Subtitle Language Select the preferred subtitle language. (c) Audio Language Select the preferred audio language for watching TV channels.
(b) Restore Factory Default Reset your Set Top Box to the DefauIt Factory Settings. In Main Menu select [Restore Factory Default] using the / keys and press OK or to select. Enter your password or the default password '0000' and press OK to confirm. This option will delete all preset channels and settings. The master unlock password is '8888'. (c) Information View model, hardware and software information (7). USB To access the Menu, press the MENU button and select [USB] using the / keys.
(b)Photo configure: -Slide Time: adjust slide show interval to 1一8 seconds. -Slide Mode: adjust slide show effect as mode 0一59 or random -Aspect Ratio: [Keep]: Play picture in its original aspect. [Discard]: Play picture in full screen mode. (c) Movie Configure: Subtitle Specific: [Small]: Displays the subtitle as small mode. [Normal]:Displays the subtitle as normal mode. [Big]: Displays the subtitle as big mode. Subtitle BG: [White]: Displays the subtitle in white background.
(8). Recording Living TV The most unique feature is its ability to record living TV. There is two ways you can headle this. the first is to connect a USB storage device to the usb port and press the record button on the remote. The other way is to schedule a program to record using the EPG. To schedule a recording following the below steps: Press the EPG button on the remote. Highlight the channel you wish to record press the OK button The schedule window will be displayed with a number of options.
Troubleshooting Problem No picture Potential Reasons Power isn't connected What to do Connect the power The power switch is not on Switch on the power Screen shows No Signal No sound from speaker Only sound, no image on the screen Remote Control is not responding DVB-T cable not connected Plug in the DVB-T cable Incorrect setting Reset setting No or incorrect connection with audio cable Connect the audio cable correctly Sound on mute Turn off mute function Incorrect sound track Try another sou
Technical Specifications Item Sub Item Parameter Tuner Input Frequency 170~230MHz 470~860MHz RF Input level -78~-82dBm IF Bandwidth 7MHz and 8MHz Modulation QPSK,16QAM,64QAM Decoder Format MPEG4 AVC/H.264 HP@L4 MPEG2 MP@ML.HL Video Audio Output Format NTSC:480i/p, 720P, 1080i, PAL ,576i/P,720P, 1080i, Output Port Decoder Format 1XHDMI(1.
