DENVER IPC-330 DENVER IPO-320
Pack list: IP camera Mounting bracket Antenna Power Adaptor CD Lan cable Installation guide Screws Note: Some models are not equipped with an external antenna Installation procedures: Start Connect the Hardware Install the Search Tool Login the IP Camera to the LAN Wireless Settings Login the IP Camera to the PC Client Access by Mobile End Note: For the first time use of the IP Camera, please refer to the procedures above.
IP Camera Internet PC Router LAN WAN Internet Cable Power Internet PC Router WAN LAN Internet Cable Power Connect the Camera with Internet cable to the router and with the power to the mains, as shown above.
1. Installation of the Search Tool Next Insert the CD and install the following software: 1. Open the file “IPC-330 & IPO-320”-”Browser View”: Click “OCX setup”—“Next”—“Install”—“Finish” 2. Open the file “Search Tool”, copy the “Search Tool” to the desktop and launch it. 2. Login IP Camera to the LAN After hardware was connected properly, launch the search tool, and the IP address of the camera will be displayed automatically.
Double click the camera IP address in the search tool. A Sign-in interface will be shown in your default browser, like below: Note: User: admin Password: None/blank (Please change the account info for safety after login) After you entered the correct user name and password, this login screen will be displayed. (It supports 6 visitors to view online at the same time) Note: 1) If you use the IE browser, please choose the first sign-in mode (ActiveX Mode) to login.
2) If you use the IE browser to connect the camera for the first time, maybe no image will be displayed, instead a an ActiveX prompt will appear, please click the prompt and choose Run Add- on, refresh the IE interface, and login the camera again, then you will see the live video. A. Click on “OCX download” to download and install it. B. Refresh the webpage and login again, the camera video will be displayed as below Live video 3.
Checking the WIFI Signal Connection Status 4. DDNS Service Settings 1). Click on the icon to access to “DDNS Service Settings”. 2). Choose the DDNS server, input the DDNS user name and password. 3). Submit, refresh, then DDNS status will be shown as “DDNS Succeed”. Thus the remote address is http://G1200.vipcam.org. For its functionality you must use the port forwarding function of your router. By this you will create a virtual server; enter the IP address and port of your camera.
5. Mail Service Settings and Alarm Service Settings 1). The Mail service settings are a requirement for the alarm function. If your camera will be activated it will send you an email with photos attached. For this, you must assure that the mail service is configured correctly and successfully tested. Here an example for Gmail. It will send an email if the camera is activated.
If you let the camera page (browser) on, if the come will be activated, 1 minute will be recorded. 6. Record & Capture Path Record & Capture Path: Where to store the files, video and photos. (If you can’t choose this, pay attention to your PC OS and IE version, please use the IE browser.) Record file length: At least 100MB Record time length: At least 5 minutes. Reserved disk space: If your pc disk space is less than 200MB, stop recording.
Record coverage: Delete old files when the SD card is nearly full. Record time: Create a video file every 10 minutes. Timer recording: Set the time, select all, store recording to the SD card. You can playback the video online with IE browser.
8. Upgrade Device Firmware & System Log 1). With this option you may reboot the camera, restore it to the factory settings, and upgrade the system. 2).
9. Basic Network Settings & PTZ Settings 1). Through setting to set some PTZ function 2).
10.
11.
FAQ: A. Password forgotten 1) Reset your camera. While the power is on, you must press the RESET button for 10 seconds. The button you will find at the bottom of the camera. With outdoor cameras the white reset button is located at the end of the power cord. 2) After the reset is completed, the camera is reset to the factory settings, then the username and the password is "admin". B.
b.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly. Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below.
