Operation Manual

ManualsBrandsDenver ManualsAudioIR-100

ENG-1

DENVER IR-100

SAFETY PRECAUTIONS

- Read all the instructions carefully before using the unit and keep them for future reference.

- Check that the voltage marked on the rating label matches your mains voltage.

Location of Unit

- The unit must be placed on a flat stable surface and should not be subjected to vibrations.

- Do not place the unit on sloped or unstable surfaces as the unit may fall off or tip over.

- The mains socket must be located near the unit and should be easily accessible.

- Avoid extreme degrees of temperature, either hot or cold Place the unit well away from heat sources

such as radiators or gas/electric fires. Avoid exposure to direct sunlight and other sources of heat.

- Never place any type of candle or naked flame on the top of or near the unit.

- To reduce the risk of fire, electric shock or product damage, do not expose this unit to rain, moisture,

dripping or splashing. No objects filled with liquids, such as vases, should be placed on the unit.

- If you spill any liquid into the unit, it can cause serious damage. Switch it off at the mains

immediately. Withdraw the mains plug and consult your dealer.

- To prevent the risk of electric shock or fire hazard due to overheating, ensure that curtains and other

materials do not obstruct the ventilation vents.

- Do not install or place this unit in a bookcase, built-in cabinet or in another confined space, ensure

that a minimum of 10cm should be kept around the apparatus for ventilation.

Safety

- Always disconnect the unit from the mains supply before connecting/disconnecting other devices or

moving the unit.

- Unplug the unit from the mains socket during a lightning storm.

- This unit will become warm when used for a long period of time. This is normal and does not

indicate a problem with the unit.

CAUTION CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISK OF ELECTRIC SHOCK

DO NOT OPEN

DANGEROUS VOLTAGE

Conductor dangerous voltage, that may be of sufficient magnitude to constitute a risk of electric

shock to persons is present within this product's enclosure.

ATTENTION

The owner's manual contains important operating and maintenance instructions, for your

safety, it is necessary to refer to the manual.

Mains Cable

- Make sure the unit is not resting on top of the mains cable, as the weight of the unit may damage the

mains cable and create a safety hazard.

- If the mains cable is damaged it must be replaced by the manufacturer, its service agent, or similarly

Summary of content (19 pages)

PAGE 1
DENVER IR-100 SAFETY PRECAUTIONS Read all the instructions carefully before using the unit and keep them for future reference. Check that the voltage marked on the rating label matches your mains voltage. Location of Unit The unit must be placed on a flat stable surface and should not be subjected to vibrations. Do not place the unit on sloped or unstable surfaces as the unit may fall off or tip over. The mains socket must be located near the unit and should be easily accessible.
PAGE 2
qualified persons in order to avoid a hazard. Interference The normal function of the product may be disturbed by Strong Electro Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in other location. This unit includes micro-processors which may malfunction as a result of external electrical interference/noise or electrostatic discharge.
PAGE 3
FEATURES AND CONTROLS 1. 2. 3. 4. 5. 6. SPEAKER BUTTON LCD DISPLAY SCROLL CONTROL/ SELECT BUTTON VOLUME+ BUTTON IR SENSOR 7. 8. 9. 10. 11. 12. 13. MEMORY BUTTON MODE BUTTON INFO BUTTON BACK BUTTON MENU BUTTON VOLUME- BUTTON ROD ANTENNA 14. 15. 16. 17. 18. HEADPHONE JACK AUX IN JACK USB DEVICE IN PORT NETWORK SOCKET DC CORD SOCKET REMOTE CONTROL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18.
PAGE 4
PUTTING THE BATTERY INTO THE REMOTE CONTROL 1. Press the battery compartment gently according to the direction indicated in the illustration. 2. Slide to open the battery compartment. 3. Insert the supplied CR2032 battery into the compartment according to the polarity markings ("+" and "-") inside the compartment and on the battery. Replace the battery compartment until it clicks.
PAGE 5
toggles between alarms in standby. SLEEP/SNOOZE When playing, standby after a set time. When alarm is sounding, snooze for a set time. MEMORY Press for the Preset recall/Save menu, Scroll up/down to select the preset number then press Select to confirm. SCROLL/SELECT On unit, Turn to scroll through a menu or station list. The chosen option is highlighted in reverse text (white characters on a dark background). Press to select. Press to previous track or hold to scan down/rewind.
PAGE 6
SET UP & CONNECTION Mains Connection 1. Connect the AC power cord to the unit via the AC socket at the back. 2. Plug the AC power cord to the AC mains outlet. Network Connection Wired network 1. Check first of all whether the control lamps (LINK/ACT) of your LAN connection or your router light up. 2. Use an Ethernet cable with RJ45 connector to connect the NETWORK socket of the radio with the LAN port of your router. 3. Proceed for the operation as described in the below "GETTING STARTED".
PAGE 7
Auto update The auto update works with data sent over DAB, FM or the Internet. The clock is only updated when in a corresponding mode, so it is recommended to select a mode that you use regularly. 1. Select auto update from DAB, FM or Network. 2. Select the appropriate time zone if the auto update is done by the Internet. 3. If your country uses daylight saving, the automatically update time may be wrong by one hour. Set the daylight savings to ON when daylight savings are in effect. Manual set 1.
PAGE 8
Standard encrypted network 1. To enter the network key (password), rotate the SELECT control to move the cursor through the characters to be selected and press on it to confirm. 2. The key that is entered will be displayed in the upper part of the display. WPS-encrypted network WPS-encrypted networks are identified by their network names as soon as the unit starts searching for available network connection.
PAGE 9
Factory reset Perform a factory reset returns the unit to factory settings. All manual settings such as time, date, network configuration and presets are deleted. The radio's current software version is not affected and remains as it was registered in the Internet-Radio- Portal. Favourites in the Internet radio remain until newly registered with another account in the Internet portal. Software update Software updates are made available from time to time.
PAGE 10
Internet Radio This radio can play thousands of radio stations and podcasts from all over the world via a broadband internet connection. When the Internet Radio mode is selected, the radio connects with the Frontier Silicon Internet radio portal to download a list of stations. Once a station is selected, the radio will connect directly to that station.
PAGE 11
selecting "Station list>My added stations>[Station]" Presets Presets are stored in the radio and cannot be accessed from other radios. To store an Internet radio preset, press and hold the MEMORY button until the display shows the "Save to Preset" screen. Select one of the 10 presets to store the current station. To select a preset, press the MEMORY button once, then select one of the listed preset stations. When a preset station is playing, "Pn" (P1, P2 etc...) will appear in the lower part of the display.
PAGE 12
Music Player The Music Player mode plays audio files such as MP3s, AACs, WMAs or FLACs from a computer on the local network. In order for the radio to play music files from a computer, the computer must be set up to share files or media. UPnP media sharing allows devices like you radio to play music from a shared media library, navigating through tag menus such as Artist, Album or Genre.
PAGE 13
album, composer and rating. Once you have located a track you want to play, press on the SELECT control, USB Playback -A. 1. Insert the USB into the port at the rear. 2. The display will show: "USB disk attached-open folder? (Yes or No) 3. Select "Yes". 4. Select your music, then press select button to playback. - B. 1. Select "Music player" mode. 2. Select "USB playback" 3. Select your music, then press select button to playback.
PAGE 14
Prune servers From time to time it may be necessary to remove servers displaying question marks in front of the server name from the server list. To perform this function, go to the "Prune servers" section and select YES. Repeat/Shuffle You can repeat tracks or play them in random order by selecting "Repeat play" or "Shuffle play" to "On". DAB Radio DAB radio mode receives DAB/DAB+ digital radio and displays information about the station, stream and track playing.
PAGE 15
and their associated frequencies. When your desired frequency appears in the display, press on the SELECT control to confirm. DRC (Dynamic range compression) If you are listening to music with high dynamic range in a noisy environment, you may wish to compress the audio dynamic range. To change DRC, press the MENU button then enter into the "DRC" section, and select DRC high, low, or off by the use of the SELECT control.
PAGE 16
Selecting stations To search for a station, press on the SELECT control once, the radio will start to scan up the frequency band, and it will stop automatically once a station has been found. Alternatively, you can also press and hold the or button to scan up or down the frequency band. To tune manually, rotate the select control for your desired frequency. Presets To store a FM preset, press and hold the MEMORY button until the display shows the "Save to Preset" screen.
PAGE 17
ALARMS AND SLEEP Alarms There are two wake-up alarms with snooze function and one sleep function to turn the radio off after a set period. Each alarm can be set to start in a particular mode. To set or change an alarm: 1. Select either Alarm 1 or 2 in the main menu or press the ALARM button on the remote control. 2.
PAGE 18
Sleep To activate the sleep function, either select it in the main menu by the use of the SELECT control or repeatedly pressing on the SLEEP button. The display will show the sleep time and you can choose from: Sleep Off, 15, 30, 45, 60, 75, 90 minutes. Once the sleep time has been set, it will return to the main menu. MUTE FUNCTION (remote control only) Press the MUTE button on the remote to stop the sound from the speakers temporarily, the sound stops and the display will show the mute icon and "Muted".
PAGE 19
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly. Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen below.