User manual SEL-85350 facebook.com/denverelectronics Before operating this vehicle, read all the instructions for safe assembly and operations. User’s manual can guide you through the functions and usage of Electric scooter. Before using this Electric scooter, familiarize yourself with how to operate, so that you can keep the Electric scooter in the best condition possible.
Table of Contents 1 Product and Accessories......................................................................................................................3 2 Unfolding and folding the scooter........................................................................................................ 5 3 Assembling the device.......................................................................................................................... 6 4 Charging the scooter..............................
1 Product and Accessories Important! This electric scooter must be charged and stored in a safe way. For safety reason and protect battery life, never charge the electric scooter in temperatures below 5 °C or above 45 °C. Equally, always disconnect the electric scooter with the power cable once fully charged. Always use the supplied power adapter to charge the electric scooter. Make sure that all screws are properly tightened to avoid unsafe situations.
charger Screw for handlebar attachment x 4 Valve extension for air tube 4 Allen key x 2
2 Unfolding and folding the scooter Unfolding the scooter 1)Place the electric scooter on its wheels like below. Unlock the hook on the handlebar. 2) Pull up the handle in a gentle way. Raise the handle slowly. Close the lock lever located on the lower part of the handlebar support tube. 3) The electric scooter is unfolded as soon as you hear the rod clicks into place. Folding the scooter 1. Release the release lever located on the lower part of the support tube of the handlebars. 2.
3 Assembling the device Before using the scooter it is necessary to install the handlebar on the frame main vehicle. 1). Insert the handlebar into the vehicle frame. 2). After matching the holes in the handlebar with those of the frame, insert the screws and tighten them well; repeat the operation also in the side opposite of the handlebar inserting a total of 4 screws.
4 Charging the scooter Connect the supplied power adapter to the charging port of the electric scooter.
5 Intended Use The Electric scooter is neither a means of transport nor sports equipment, but a device for personal entertainment. The Electric scooter for domestic use only and only by a person aged at least 14 with a maximum weight of 120 kg. The other parameters for the permissible operation of the Electric scooter are defined in the section (“10. List of parameters”) .
loosen or damage the spring holding the fender. As a result, the brake pad constantly touches the wheel and the motor temperature increases due to the additional resistance. The rear tire can also get loose if the brake is in constant braking position. Avoid constant braking. As a result, the tires will not only wear off, but also become hot. This will soften the rubber and it will no longer have the same grip on the road as usual. Do not touch the tire after braking.
temperatures from 15-25° Celsius. This is not a failure on the batteries, but normal behavior. Please notice: Even a fully charged battery will run out of power if the electric scooter is not used for a period. Expect a fully charged battery to keep power between 90 and 120 days in off mode, before it is fully discharged. If only partially charged, this period is lower. Please make sure the battery does not get above 50° Celsius, or below minus 10° Celsius for a longer period. (e.g.
WARNING ● ● ● ● ● ● Please make sure to check that the steering system is correctly adjusted and that all connection components are firmly secured and not broken before riding, refer to handle assembly and safety instruction. Please read operation guide and warnings of correct techniques for use and braking Always wear shoes. We highly recommend to always wear helmet/pads for your own protection. Self-locking nuts and other self- locking fixings may lose their effectiveness.
8.2 Button and speed transfer Only power buttons in the display, press”Power” button with 5s, the scooter power on! Press one time to turn on /off the front LED light. Press “power” 2 times constantly to tranfer the speed with 3 gear, ECO: 6KM/H, D: 15KM/H, S: 20KM/H You have to manually move the Electric scooter with your foot before the accelerator button works. 9 Electric scooter riding 1. Press “Power” buttons to adjust speed level. 2.
10 List of parameters Parameter Size Quality Ride Condition Electric scooter Battery Type: Li-ion battery Motor Power adapter Folding size(mm) Unfolded Size(mm) Max Load(kg) Weight (kg) Age(Year) Max. speed (horizontal riding) (km/h) Distance up to (km) Terrain Nominal voltage (V) Input voltage (V) Battery capacity (mAH) Motor Power (W) Emission sound pressure level (DB) Rated input voltage (V) Rated output voltage (v) Rated current (A) Charging Time(h) Range 1085*435*490 1085*435*1135 120 14.
11 Electric scooter safe parking Once you have stopped the Electric scooter, get off it and press the side stand down with your right foot to support the Electric scooter. The side stand is located on the left-hand side of the Electric scooter below the foot board. Before you ride again, push the side stand back up so that it is parallel to the foot board.
WARNING Do not try to make a turn too fast. WARNING Lithium battery inside. WARNING If the Electric scooter switches off, the system will block the vehicle automatically. It can be released again by pressing On/Off. ● Use the device only at temperatures between -10 °C and +45 °C. 13.4 Range per charge The range depends on several factors: ● Topography: On level paths you have a greater range than on uneven ground. ● Weight: The range depends on the rider's weight.
● While riding, your feet must always be on the foot board. ● The Electric scooter can accommodate only one person. ● Do not start or stop abruptly. ● Avoid riding on steep slopes. ● Stop riding the Electric scooter if you hit a solid object (such as a wall or other structure) with it. ● Do not ride in dimly lit or dark places. ● Ride the Electric scooter at your own risk, we assume no liability for accidents or damage. ● Ride at a safe speed that allows you to stop at any time.
reduced. Therefore, there is a potential risk of injuries and material damage. ● Store and charge the device in an open, dry area away from combustible materials. ● Do not charge the device in direct sunlight or in the vicinity of open flames. ● Do not charge the device immediately after use. Allow the device to cool down for an hour before charging it. ● If the device is left to other people, it must be charged partially (20 - 50%), not fully.
Please notice - All products are subject to change without any notice. We take reservations for errors and omissions in the manual. ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly.
Regarding Battery charging SEL-85350 Important – Please read! Dear customer. We hope you get a lot of joy out of your new Electric scooter. The battery built in the Electric scooter is not fully charged from production line and when left unused the battery can slowly discharge by itself. This can lead to slow charge if the battery is fully discharged, but this is done to avoid damage to the battery.
WARNINGS Please read the manual completely and the instructions below before using the product. Product names: SEL-85350 Product type: Electric scooter Year of manufacturing: 2020 • Note: ONLY use the supplied charger labelled XHK-800B-4220 with the following output voltage to charge this Electric scooter: 42V – 2A. • Using another charger may damage the product or create other potential risks. • Never charge the product without supervision.
DENVER ELECTRONICS A/S EC Declaration of Conformity (Machinery Directive) The undersigned Company Name: Address: DENVER ELECTRONICS A/S Omega 5A, Soeften, DK-8382 Hinnerup, Denmark certify that the design and manufacturing of this product Product Brand Name: DENVER Product Model No.