Infrared Trail Camera User's Manual WCS-5020 Package List: * Camera * Mounting Strap * USB Cable * User Manual 1
Parts Of The Camera 1. Display screen 2. IR lamps 3. Lens 4. Up/Video Button 5.
6. Motion sensor 7. OK/Shot button 8. Menu Button 9. Right button 10. Playback button 11. DC adapter port 12. Tripod Slot 13.
13. Battery compartment 14. ON-TEST-OFF button 15. USB jack Power Supply Please install batteries before using the camera. Unlock the camera and you will find the battery compartment. Install 4 pieces of 1.5V AA batteries. Please make sure the battery polarity is correct. Inserting the Memory Card • Please prepare a Micro SD card and insert it into the camera for saving files. Before recording, please format the memory card first.
• For the first time of use, please wait for the memory card temperature reach the ambient temperature. The camera will be short-circuited by environment temperature and humidity. Please protect the camera when using it outdoor. • If the capacity of memory card is full, the camera will stop recording automatically. • Press the edge of the card gently to pop-up the TF card. Basic Operation Turn On / Off the Camera • Switch the Mode Button to “Test /On” to turn on the camera.
2. Press Up/Down button to scan all menus. Then press OK button to enter the options interface. 3. Press Up/Down button to scan all options. And press OK button to confirm options. 4. Press Menu button again to turn back to last menu or exit the setup menu. Following below instructions to set up the menus and functions: Mode Set the working mode. In photo mode, the camera just takes pictures. In Video mode, the camera just records videos.
Video Resolution Set the video resolution. The larger the resolution is, the longer the video time will be stored. Options: [1920x1080P]/[1280x720P]/[720x480P]/[640x480P]/ [320x240P]. TL Video Resolution Set the resolution of a time-lapse video. Options:[2592x1944P]/[2048x1536P]. Video Length Set the duration of recording a video clip. The shortest time can be set is 3 seconds and the longest time is 10 minutes. Options: 3 seconds~10 minutes.
Options: 5 seconds~60 minutes. IR Distance Set the distance of infrared induction. Options: [Near]/[Middle]/[Far]. Sensitivity Motion Sensors • Set the sensitivity level of the sensor. Normally the environmental impact is small in indoors, you can choose “Low” sensitivity. In normal condition of outdoor, choose “Middle”. Choose “High” if the environment impact is huge in outdoors. • The temperature can also impact the sensor sensitivity.
Time-lapse In Time-lapse menu, there are three options as below: [Normal]: The camera will take pictures automatically as per set time interval. For example, set the interval time to 1 hour, the camera will take a photo each hour. If you want to observe a plant blooms, the camera will take 24 photos in 24 hours to record the whole process of blooming. [TL Video]: You can set the interval time within a time range to take photos and convert these photos into a video.
[Off]: Close the time-lapse function. Language Set the language display on screen. Options: [English]/[German]/[Danish]/[Finnish]/[Swedish] [Spanish]/[French]/[Italian]/[Dutch]/[Portuguese]/[Simplified Chinese]/[Japanese]. Endless Capture Set the camera to record video in loop. Options: [On]/[Off]. Time & Date Set the date and time of camera. Press Right button to choose an item and press Up / Down button to adjust the value. And then press OK button to confirm.
• Options of date format: dd/mm/yyyy, yyyy/mm/dd, mm/dd/yyyy. • Options of time format: 24h, 12h. Options: [Set time & date]/[Time format]/[Date format]. Photo Stamp Stamp the date & time on the photos. Options: [Time & date]/[Date]/[Off]. Password Protection Set the power-on password of the camera. The password is four digits; each digit can be select from 0 to 9. If you forget the password, please reset the camera. Then all parameters will reset to the factory settings. Options: [On]/[Off].
Beep Sound Open/close the touch-tone. Options: [On]/[Off]. Format Memory Card Formatting the memory card will delete all data permanently. Before using a new memory card or a card that has been used in another device previously, please format the memory card. Options: [Yes]/[No]. Serial No. Set the unique serial number for the camera. The number is four digits, each digit can be selected from 0 to 9 and A to Z. Options: [On]/[Off].
Take Photos, Record Videos, Playback Switch the Mode Button to “Test”. In this mode, you can take photos, record videos and playback files manually. • Take Photos: Press Capture button to switch to photo mode. Press Shot button to take a picture. • Record Video: Press Video button to switch to video mode. Press Shot button to record a video clip. Press Shot button again to stop recording. • Playback: Press Playback button to enter the playback interface. Press Up/Down button to scan photos or videos.
Working Mode Switch the Mode Button to “On”. After turning on the camera, the screen will display 15 seconds countdown. Then the LEDs and screen will go out. The camera begins to operate independently and enter standby mode. • If the wild animals enter the detection range of the motion sensors, the camera will be activated and detect the motion trail. • If the wild animals continue to move to the detection zone of the sensor, the camera will take photos or record video automatically.
Using a Card Reader 1. Pop-up the memory card from the camera and insert it into a card reader. Then connect the card reader to a computer. 2. Open [My Computer] or [Windows Explorer] and doubleclick the removable disk icon that represents the memory card. 3. Copy image or video files from the memory card to your computer. Connecting the Camcorder to a PC by the USB Cable 1. Connect the camera to the computer via a USB cable. Turn on the camera, the screen displays “MSDC”. 2.
Please notice - All products are subject to change without any notice. We take reservations for errors and omissions in the manual.
electric and electronic equipment and batteries) is not handled correctly. Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen above. This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other household waste, but should be disposed of separately. As the end user it is important that you submit your used batteries to the appropriate and designated facility.
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.denver-electronics.com and then click the search ICON on topline of website. Write model number: WCS-5020. Now enter product page, and red directive is found under downloads/other downloads. DENVER ELECTRONICS A/S Omega 5A, Soeften DK-8382 Hinnerup Denmark www.facebook.