Manual

ManualsBrandsDerale Performance ManualsPower suppliers2 Pass 8" Series 7000 Copper_Aluminum Power Steering Kit

KIT CONTENTS

QTY. DESCRIPTION

1 Oil Cooler

4ft. 11/32” OEM Spec Hose

4 Hose Clamps

Please read these instructions completely before starting the installation.

13200-13210-13212-13213-InstructionSheet

TOOLS NEEDED

Standard Screw Driver

or 5/16” Nut Driver

Dyke Pliers

Razor Knife

QTY. DESCRIPTION

2 Mounting Rods

2 Mounting Clips

Foam Pads

2 1x1

INSTALLATION INSTRUCTIONS

POWER STEERING COOLER KIT

PART # 13200, 13210, 13212 & 13213

(Continues on Page 2)

The Power Steering Cooler can be mounted in multiple locations on your

vehicle. Reference Diagram # 1 for possible cooler positions. #1 is the

ideal location, #2 is second best and #4 being the last choice.

The Cooler core will flow in either direction, there is no specified inlet

or outlet port.

Note:

Diagram #1

COOLER INSTALLATION

(See Diagram #2)

1. Identify the 2 Mounting Rods, 2 Mounting Clips and 2 1x1 Foam

Pads.

2. Install the 2 Mounting Rods thru the Oil Cooler.

3. Take the 1x1 Foam Pads supplied, peel off the paper lining & slide

them onto the Mounting Rods, sticking them against the Cooler.

4. Take the Cooler Assembly with attached looped hose and hold in

the desired location.

5. Install the 2 Mounting Rods thru the Radiator/Condenser core.

Do not use excessive force when pushing the Mounting

Rods through the Radiator/Condenser. Excessive force

could cause damage to the fins and possibly puncture a

tube.

6. Take the Mounting Clips supplied, making sure they are in the

correct direction (Derale writing out) install onto the Mounting Rods

and cinch them until the 1x1 Foam Pads are slightly compressed.

7. Cut off any excess Mounting Rods.

Mounting

Warning:

COOLER LOCATION

When selecting the best location for your vehicle, always consider a

location that will deliver the maximum airflow.

PRE-INSTALLATION

ecure in place using the Hose Clamps. (See Diagram #2)

1. Identify the 11/32” X 4’ Hose and Hose Clamps.

2. Slide one hose clamp on each end of the supplied Hose.

3. Using a dab of oil, lubricate each end of the hose and install hose onto the cooler inlets forming a loop.

4. S

Diagram #2

Mounting

Rods

Foam

Pads

Mounting

Clips

4’ Hose

IMPORTANT

This cooler is designed to install

on the Low Pressure side of the

pump. Do not cut or remove the

High Pressure hose.

Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS POWER STEERING COOLER KIT PART # 13200, 13210, 13212 & 13213 Please read these instructions completely before starting the installation. KIT CONTENTS QTY. 1 4ft. 4 DESCRIPTION Oil Cooler 11/32” OEM Spec Hose Hose Clamps QTY. DESCRIPTION 2 Mounting Rods 2 Mounting Clips 2 1x1 Foam Pads TOOLS NEEDED IMPORTANT Standard Screw Driver or 5/16” Nut Driver Dyke Pliers Razor Knife This cooler is designed to install on the Low Pressure side of the pump.
PAGE 2
ROUTING HOSES This cooler is designed to install on the Low Pressure side of the power steering pump. (See Diagram #3) 1. Identify the Low Pressure hose coming from the power steering pump. The Low Pressure hose is usually smaller and is secured by a hose/band clamp. The High Pressure hose is usually larger and has swedged fittings. 2. Disconnect the Low Pressure hose from the power steering pump. 3. Carefully route the looped hose now attached to the cooler toward the power steering pump.