Manual

15781-InstructionSheet
INSTALLATION INSTRUCTIONS
OIL FILTER RELOCATION KIT
PART # 15781
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com
Please read these instructions completely before beginning installation
TOOLS NEEDED
KIT CONTENTS
QTY. DESCRIPTION
1 Spin-On Adapter
1 Ports Up Filter Mount
1 O-ring (Spin-On Adapter)
1 3/4-16 Filter Nipple
10ft. 1/2” Hose
QTY. DESCRIPTION
2 1/2” NPT Plug
4 1/2” NPT x 1/2” Hose Barb
4 Hose Clamps
3 #14 Sheet Metal Screws
Diagram #1Diagram #1
PRE-INSTALLATION
VEHICLE TESTING
1. Remove the factory oil filter and clean the oil filter landing surface on
the engine block.
2.
3.
1. Apply a light coat of oil onto the O-ring.
2. Take the O-ring and install into the groove on the Spin-On Adapter.
3. Install onto the engine. (See Diagram #1)
4. Hand Tighten with the same force used in tightening a factory oil filter.
1. Choose a convenient location for the Ports-Up Filter Mount. Make sure
there is enough space for future servicing of the oil filter. Suggested
Locations: Firewall, Radiator Support, Fender well. (See Diagram #2)
2. Take the 3/4-16 Filter Nipple supplied, making sure the shorter end of
threads is installed onto the Ports-Up Filter Mount.
3. Using the filter mount as a template, mark & drill three 3/16” holes.
4. Using the #14 Sheet Metal Screws provided, install the Ports-Up Filter
Mount onto the vehicle.
1. Using the Hose Clamps provided, attach both ends of the 1/2” Hose
provided to the hose barbs on the installed Spin-On Adapter forming a
loop. (Apply a thin coat of oil to the Hose Barbs so the hose slips on
easily.)
2. Carefully route hose over to the Ports-Up Filter Mount.
Keep hoses away from sharp edges, moving parts and exhaust.
Do not bend hose sharper than a 5” radius.
3. Cut the hose to the proper length.
4. Using the Hose Clamps provided, attach the hose coming from the OUT
on the Spin-On Adapter to the IN on the Ports-Up Filter Mount.
5. Using the Hose Clamps provided, attach the hose coming from the IN
on the Spin-On Adapter to the OUT on the Ports-Up Filter Mount.
6. Apply a light coat of oil onto the o-ring of your new oil filter and install
on the filter mount.
1. Start the engine and quickly check all connections for leaks.
2. Turn-off the engine and check the oil.
3. Add oil as needed.
SPIN-ON ADAPTER INSTALLATION
FILTER MOUNT INSTALLATION
Hose Routing
Note:
After determining the orientation of the Spin-on Adapter, using Teflon
Tape or suitable sealant, install two 1/2" NPT x 1/2" Hose Barb fittings
onto the correct “IN” and “OUT” ports on the Spin-on Adapter.
Take the two 1/2” NPT Plugs provided, using Teflon Tape or suitable
sealant; install them in the remaining ports on the Spin-on Adapter.
4. Take the remaining two 1/2" NPT x 1/2" Hose Barb fittings, using Teflon
Tape or suitable sealant; install them onto the Ports-up Filter Mount.
Hose
Barb
Hose
Barb
O-ringO-ring
7/8” Open End Wrench
Standard Screw Driver
1/8” Allen Wrench
Drill
3/16” Drill Bit
Teflon Tape
PlugPlug
Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working on
vehicles. Always use eye protection (goggles, safety glasses or shield). Park the vehicle in a well lit area, on level ground and apply the
parking brake. Only work on a cold vehicle that has been sitting overnight, failure to do so will result in severe burns and injury. Before starting
the vehicle, make sure no tools or any other items are left under hood that could interfere with or be drawn into moving parts of the engine.
Failure to follow instructions can lead to severe damage and personal injury.
Diagram #2Diagram #2
Filter
Mount
Filter
Mount
Fire
Wall
Fire
Wall
Diagram #3Diagram #3
BRAND PART #
AC
Fram
Motorcraft
Purolator
PF2
PH8A
FL1A
PER1A
OIL FILTER CHART
IMPORTANT
The new Filter Mount is designed to accept a 3/4-16 oil filter (Typical
Ford filter) Use Derale Part # 13092 or reference Oil Filter chart.