Owner's Manual

ManualsBrandsDesa Tech ManualsHeatersDesa Tech PC-GL36

Parts included with this kit:

Part No. Description Quantity

Tools Required

• 7/8" Open End Wrench or

Adjustable Wrench

• 3/4" Open End Wrench or

Adjustable Wrench

• 3/8" Deep Socket Drive

CONVERTING FROM NATURAL GAS TO PROPANE/LP GAS

For Use When Converting Model

GL36 Series Vented Decorative Fireplace

This conversion kit must be installed by a qualified

service agency.

Read these instructions completely before installing this conversion kit.

Before proceeding, make sure the gas control valve is in the “OFF”

position, all electrical power to the appliance is OFF, and the

fireplace is cool to the touch.

CAUTION: The gas supply shall be shut off prior to

disconnecting the electrical power before proceed-

ing with the conversion.

INSTALLATION INSTRUCTIONS FOR

PC-GL36 CONVERSION KIT

Save this manual for future reference.

For more information, visit www.desatech.com

• Torx T20 or Slotted Screwdriver

• 5/32" Allen Wrench

• #2 Short Phillips Screwdriver

• Thread Sealant

(Resistant to Propane/LP)

ACCESSING THE FIREPLACE

You may access the burner system through the opening in the front

of the unit.

1. Remove front glass panels (if installed). This will keep them

from being damaged. To remove, partially open doors. Press

up on the upper spring clip of one door panel with a screw-

driver until the outer top pivot pin is free of the clip (see Fig-

ure 1). Repeat with second door panel. Place glass panels safetly

out of your work area.

2. Slide open the screens and tuck them inside the outer pockets

on the firebox.

Figure 1 - Removing Glass Doors

Spring Clip

Depress Spring

Clip to Release

Pivot Pin

Remove

Bottom Pin

From Pivot

Plate While

Sliding Door

Out of the

Upper Track

Pivot Plate

116929-0

1 Instruction Sheet 1

23106 Main Burner Orifice LP 1

108085-0

2 Injector, LP#30 1

106380-0

1 Gas Valve Regulator#49 1

117485-01 Conversion Label, English 1

106739-0

1 Registration, Gas Conversion 1

106080-0

1 Conversion Information Label 1

116932-01Carton Label PC-GL36 Series 1

Summary of content (4 pages)

PAGE 1
TM INSTALLATION INSTRUCTIONS FOR PC-GL36 CONVERSION KIT For more information, visit www.desatech.com CONVERTING FROM NATURAL GAS TO PROPANE/LP GAS For Use When Converting Model GL36 Series Vented Decorative Fireplace This conversion kit must be installed by a qualified service agency. Spring Clip Depress Spring Clip to Release Pivot Pin Read these instructions completely before installing this conversion kit.
PAGE 2
DISASSEMBLING THE HEARTH AND BURNER SYSTEM 1. Remove the four brick panels by lifting each inner edge above the burner assembly and sliding the brick forwards the grate stand. Lift the outer edge out and over the flanges of the facings. If necessary, you can remove the remaining bricks on the opposite side. Glass Door 2. Remove the grate with the logs by lifting the grate portion off its stands and place the entire assembly outside of the unit for easy reassembly.
PAGE 3
Mounting Screws 2. Pressure Regulator Tower 3. Insure that the rubber gasket is properly positioned on the new pressure regulator assembly. Install the new pressure regulator assembly to the valve using the new mounting screws supplied with the kit. Tighten screws securely (approximately 25in-lbs.) See Figure 5. Install the identification label enclosed with the gas valve regulator to the valve body where it can easily be seen (see Figure 5).
PAGE 4
FINAL PREPARATION PILOT ORIFICE CONVERSION 1. 2. 3. 4. Remove the pilot hood assembly by pulling up until it disengages from the barrel. Do not remove the retainer clip (see Figure 9). Remove the pilot orifice from inside the barrel using a 5/32" allen wrench to unscrew the orifice. Replace pilot orifice with LP orifice supplied with this kit. The number 30 is stamped on the sleeve for identification.