Specification

CONTACT SUPPORT
PHONE: [phone]
EMAIL: [e-mail]
ADDRESS: 8715 Boston place, Rancho Cucamonga, CA. 91730
www.designelementusa.com
SAFETY AND PRECAUTIONS
• Avoid using any type of rough cleaning material on top of the cabinet
nish.
• Use mild liquid soap and water-dampened soft cloth to remove stains from
the cabinet and to clean the countertop.
• For the glass part of the mirror, use ammonia-free cleaning products.
CLEANING AND CARE
!
While turning around the double
sink counter tops, always add
support from the centre for
safety
• Please go through this entire instruction manual before making any
attempt to assemble, operate or install the product.
• During installation, handle countertop and sink with optimum care. It
might break if hit hard on a solid surface.
• Don’t start using the vanity right away. Wait for approximately 24 hours
after installation so that the silicon glue can dry.
• When scrubbing the cabinet while cleaning, make sure you do not remove
or scratch the nish.
1.
2.
3.
4.
24h
1.
2.
3.
1.
2.
INSTRUCTION MANUAL
12"or 16"
1.
2.
3.
4.
4×
4×
12"or 16"
1.
2.
3.
4. 6.5.
Installing the drain
3. Connect the trap onto the drain bottom.
2. Tie up the mounting rubbers and metal rings from the bottom of the drain.
1. After installing the counter top on the cabinet, put the drain assembly inside
the hole in the sink and x it rmly.
Attaching Counter Top To Cabinet
2. Place the countertop on the glued
cabinet.
1. Apply continuous stream of quality
silicon glue to the top of the cabinet
where the countertop needs to be
placed.
2. Position and place the vessel sink in a way that the hole on the sink gets aligned with the cut out area on the countertop.
3. Don’t start using the vanity right away. Wait for approximately 24 hours so that the silicon glue can dry.
1. Add silicon glue to the back of the vessel sink.
Attaching Sink To The Counter Top
Hanging Mirror On The Wall
4. Hang the mirror on to the screws.
3. Insert the plastic plugs into the drilled holes and then insert screws into the
plastic plugs. Tie up the screws till they remain at least 0.5” – 0.75” outside the
wall.
2. Locate the studs on the wall. They are normally placed 12” to 16” apart from
each other. Drill two holes on the studs as per your previous measurement.
1. Measure the distance between the screw holes from the back of the mirror.
Wall mounting the cabinet in the wall
5. Place the cabinet against the wall, insert screws and tighten them to secure the cabinet. It is recommended that before
positioning your cabinet with the wall, place a support beneath the cabinet so that it becomes easier to handle the weight.
6. After installation, conrm that the cabinet is rmly tted so that it does not rock or move. Remove the support placed
beneath after installation.
4. As per your chosen height, drill four holes inside the studs on the wall.
3. Measure the screw holes behind the vanity cabinet.
2. Locate the studs on the wall. Studs are generally spaced 12"- 16" apart on the wall.
1. The recommended height of a wall mounted vanity is 32” to 34” inches above the ground. Measure a comfortable height
according to your need and mark it on the wall.
WARRANTY
Design Element warrants cabinets, mirrors, nishes and ttings to be free
from defects in workmanship and materials under normal use and service
for a period of one (1) year.
Please report any damage or missing pieces of your vanity to us immedi-
ately. These things must be reported no later than 30 days from the date of
delivery.
PACKING LIST
• Pre-assembled cabinet
• Countertop
• 2 Sinks
• 2 Mirrors
• Mirror mounting screws
• Drain
• Cabinet mounting screws
• Instruction Manual
BACK
FRONT
DRAWER
DEC004
COLLECTION: Portland
DIMENSIONS: W 62” | D 20” | H 28”
SKU CODE:
21”
60”
19”
9 1/2”
11”
5”
16”
5”
9 1/2”
22”
22”
16”
15”
14 ”
23 1/2”
62”
31 1/2”
35”
20”
6”
3 1/4”
7”
7”
7”