Specification

CONTACT SUPPORT
PHONE: [phone]
EMAIL: [e-mail]
ADDRESS: 8715 Boston place, Rancho Cucamonga, CA. 91730
www.designelementusa.com
• Having your entire sink and countertop as one, non porous material, makes
it extremely easy to clean and maintain.
• Avoid using any type of rough cleaning material on top of the cabinet
nish.
• Use mild liquid soap and water-dampened soft cloth to remove stains from
the cabinet and to clean the countertop.
• For the glass part of the mirror, use ammonia-free cleaning products.
CARE AND CLEANING
!
While turning around the double sink counter tops, always add
support from the centre for safety
!
While turning around the double sink counter tops, always add
support from the centre for safety
•Please go through this entire manual before attempting to assemble, oper-
ate or install the product.
•While installing support for counter top, handle the integrated sink coun-
tertop with special care. Make sure the support is fully tightened up before
you put the countertop over it.
•Do not use the vanity instantly after installation. Once you have applied
glue to attach the countertop and sink, wait for approximately 24 hours to
let it dry.
•Avoid extreme hot then cold water on the glass sinks and countertops, as it
might damage it.
•When scrubbing the cabinet, make sure you do not remove or scratch the
nish.
SAFETY AND PRECAUTIONS
1.
2.
3.
Installing A Drain
1. After installing the sink on the countertop, put the drain assembly inside the hole in the sink and x it rmly.
2. Tie up the mounting rubbers and rings from the bottom of the drain.
3. Connect the trap onto the drain bottom.
24h
1.
2.
3.
1. Apply continuous stream of quality silicon glue to the top of the cabinet where the integrated sink needs to be placed.
2. Place the integrated glass sink on the glued cabinet.
3. Do not use the sink instantly. Wait approximately for 24 hours so that the silicon glue can dry.
Attaching Counter Top To Cabinet
1.
2.
3.
4.
Hanging Mirror On The Wall
1. Measure the distance between the screw holes from the back of the mirror.
2. Find the studs on the wall. They are normally 12” to 16” apart from each other. Drill two holes on the studs as per your
measurement.
3. Insert the plastic plugs into the drilled holes. Insert screws into the plastic plugs. Leave the screws at least 0.5” – 0.75”
inches outside.
4. Hang the mirror on to the screws.
12"or 16"
1.
2.
3.
2. Tie the rubber and steel parts on the screw to hold it
3. Mount the round metal cylindrical support over the screw. Tie till it gets rmely attached
1. Open the drawer and put the screw inside the hole placed on the cabinet
Installing Support For Countertop
PACKING LIST
• Pre-assembled cabinet
• Integrated sink countertop
• 1 Mirror
• 4 Cabinet legs
• Mirror mounting Screws
• Drain
• Instruction Manual
WARRANTY
Design Element warrants cabinets, mirrors, nishes and ttings to be free
from defects in workmanship and materials under normal use and service
for a period of one (1) year.
Please report any damage or missing pieces of your vanity to us immedi-
ately. These things must be reported no later than 30 days from the date of
delivery.
BACK
FRONT
DEC015D
COLLECTION: Huntington
DIMENSIONS: W 60” | D 22” | H 35 1/2”
SKU CODE:
INSTRUCTION MANUAL
DRAWERDRAWERDRAWERDRAWER
59”
60”
28”
39”
17 1/2”
58”
11 1/2”
11 1/2”
11 1/2”
3 1/2”
16 1/2”
35 1/2”
8”
8”
7 1/2”
15 1/2”
18”
8”
8” 8”
16”