Installation Sheet

ManualsBrandsDesign House ManualsBathroom FaucetsDesign House Double Handle Widespread Bathroom Faucet

Your new Design House faucet will give you years of trouble free performance. Thank you for

choosing our product for your home. Please read all of these instructions carefully before

installing your new faucet.

When installing your new faucet, hand tighten the connector nuts, then use one wrench to

anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that

are too tight will reduce the integrity of the system.

Wrap threaded

connections (except aerator thread in spout or where o-ring or rubber sealant

are present) with Teflon tape available from your local hardware or plumbing supply store.

Always wrap in a clockwise direction.

IMPORTANT POINTS

SAFETY TIPS

ALWAYS protect your eyes with safety glasses.

Helpful tools to install this faucet:

Teflon tape

(2) crescent wrenches

basin wrench

flashlight

faucet supply tubes

silicon sealer

Brass finishes are polished, then protected with a PVD or a lacquer coating to help prevent tarnishing.

Clean these surfaces only with a damp, soft cloth.

Your new Design House faucet is designed to give you years of trouble free performance. Avoid abrasive

cleaners, steel wool and harsh chemicals that will dull the finish and void your warranty.

CONSUMER PROTECTION WARNING

To reduce the amount of lead in your drinking water, allow the water to run for a moment before

filling your glass and remember to always use cold water for drinking purposes.

Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the

amount of lead used in brass and solder. Your new faucet is made in strict compliance with

all government standards. The materials used in the manufacture of this faucet are of industry

standard quality and are s

imilar to other plumbing products having brass fittings.

Keep it looking like new by cleaning it periodically with a mild solution of soapy water. Rinse thoroughly and

then dry with a soft cloth.

1. Shut off water supply. Remove the old faucet, taking care not to damage existing water lines. Clean the surface in preparation for new faucet.

4. Align the tabs (4A & 4B) on the quick connect

assembly (4C). Push the quick connect assembly (4C)

firmly upward and snap it onto the receiving tube tab.

Pull down moderately to ensure the connection has

been made. If it is necessary to remove the quick

connect assembly (4C), squeeze the tabs on the hose,

and then pull down to disconnect.

. Making the waterline connections: Use 1/2 in.

I.P.S. faucet connections (5B, not included), or use

the supplied coupling nuts (5C) with a 3/8 in. O.D.

ball-nose riser (5A, not included). Before tightening

the faucet connector to the water supply, apply a

second wrench to the supply tube fitting. This will

prevent the supply tube from moving or twisting when

tightening the faucet connector. Do not overtighten.

6. IMPORTANT: After installation is complete,

remove the aerator to flush the water lines. Do not

lose the gasket (6A) in the aerator. Turn on the water

supply and allow both hot and cold water to run for at

least one minute each. This flushes away any debris

that could cause damage to internal parts. While the

water is running, check for leaks. Turn off the water

and replace the aerator.

2.Slide hot and cold end valves through sink

mounting holes. Make sure long tubes are installed

away from the spout. Handles should point out when

in off position. The hot side handle is indicated by a

tag with red printing. Secure end valves with metal

washers and threaded brackets. Hand

tighten brackets onto shank. Lock brackets into

position by tightening screws.

3.Place spout through mounting hole in sink. Secure

spout with rubber washer, metal washer and nut.

Summary of content (2 pages)

PAGE 1
Your new Design House faucet will give you years of trouble free performance. Thank you for choosing our product for your home. Please read all of these instructions carefully before installing your new faucet.
PAGE 2
o o 525733,813667 - Satin Nickel 525741 - Polished Chrome Problem: Faucet leaks from under handle. Cause: Bonnet is loose or o-ring on cartridge is dirty or twisted. Action: 1. Move handle to OFF position. Unscrew the set screw on the side of the handle seat. Then remove the entire handle assembly. 2.Tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON position. The leak should stop around the cartridge stem. 3. If the leak does not stop, shut off the water supply.