Installation Sheet

ManualsBrandsDesign House ManualsKitchen FaucetsDesign House Trenton 1.8 GPM Single Hole or Standard Kitchen Faucet - Includes Side Spray and Escutcheon

Your new Design House faucet will give you years of trouble free performance. Thank you for

choosing our product for your home. Please read all of these instructions carefully before

installing your new faucet.

When installing your new faucet, hand tighten the connector nuts, then use one wrench to

anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that

are too tight will reduce the integrity of the system.

Wrap threaded connections (except aerator thread in spout or where o-ring or rubber sealant

are present) with Teflon tape available from your local hardware or plumbing supply store.

Always wrap in a clockwise direction.

IMPORTANT POINTS

SAFETY TIPS

ALWAYS protect your eyes with safety glasses.

Helpful tools to install this faucet:

Teflon tape

(2) crescent wrenches

basin wrench

flashlight

faucet supply tubes

silicon sealer

6. IMPORTANT: After installation is

complete, remove the aerator to flush the

water lines. Turn on the water supply and

allow both hot and cold water to run for at

least one minute each. This flushes away any

debris that could cause damage to internal

parts. While the water is running, check for

leaks. Turn off the water and replace the

aerator.

5. Making the waterline connections:

Use 1/2 in. I.P.S. faucet connections

(5B, not included), or use the supplied

coupling nuts (5C, not included) with a

3/8 in. O.D. ball-nose riser (5A, not

included). Before tightening the faucet

connector to the water supply, apply a

second wrench to the supply tube

fitting. This will prevent the supply tube

from moving or twisting when tightening

the faucet connector. Do not

overtighten.

4. Place the faucet assembly (4A) in

position on the sink. Secure the faucet

assembly to the sink using the mounting

nuts (4B) provided. Hand tighten only.

NOTE: If the sink is uneven, use silicone

under the gasket (4C).

1. Shut off water supplies. Remove the old

faucet. Place the gasket (1A) on the bottom

of the new faucet assembly. If your model

has a side sprayer, proceed to step 2. If

your model does not have a side sprayer,

skip to step 4.

2. Insert the sprayer support (2A) through

the far right hole on the sink. Screw the

sprayer mounting nut (2B) onto the

sprayer support (2A) shank from

underneath the sink, and hand tighten.

3. Insert the side sprayer (3A) hose down

through the sprayer support (3B) and sink.

Align the tabs (3C & 3D) on the quick

connects (3E). Push the quick connector

housing firmly upward and snap it onto the

receiving tube tab. Pull down moderately to

ensure the connection has been made. If it

is necessary to remove the quick connector,

squeeze the tabs on the hose, and pull down

to disconnect.

Summary of content (2 pages)

PAGE 1
Your new Design House faucet will give you years of trouble free performance. Thank you for choosing our product for your home. Please read all of these instructions carefully before installing your new faucet.
PAGE 2
o o 547299 - Satin Nickel 547281 - Polished Chrome Problem: Faucet leaks from under handle. Cause: Bonnet is loose or o-ring on cartridge is dirty or twisted. Action: 1. Move handle to OFF position. Remove index and unscrew the set screw on handle. Then remove the handle. 2.Remove cap and tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON position. The leak should stop around the cartridge stem. 3. If the leak does not stop, shut off the water supply.