Installation Sheet

ManualsBrandsDesign House ManualsKitchenKarsen Single-Handle Standard Kitchen Faucet in Polished Chrome

SINGLE HANDLE KITCHEN FAUCET

4-8-16

Design House is a registered brand

of DHI Corp.Mequon,WI 53092

1-800-558-8700

PREPARATION

SAFETY INFORMATION

Before beginning assembly of product, make sure all parts are present.

Compare parts with package contents list and hardware contents. If any

part is missing or damaged, do not attempt to assemble the product.

Contact customer service for replacement parts.

Estimated Assembly Time: 30 minutes

Tools Required for Assembly (not included): Adjustable Wrench, Groove

Joint Pliers, Pipe Wrench, Phillips Head Screwdriver, and Supply Lines.

Installations may vary depending on how the previous faucet was

installed. Supplies necessary for the installation of the faucet are not

all included; however, they are available wherever plumbing supplies

are sold.

Prior to beginning installation, turn off the hot and cold water lines,then

turn on the old faucet to release built-up pressure. When installing the

new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN.

Connections that are too tight will reduce the integrity of the system.

Please read and understand this entire manual before attempting to

assemble, operate or install the product.

WARNING

• Protect your eyes with safety glasses when cutting or soldering water

supply lines.

CAUTION

• If you solder the joints during installation of the faucet, the seats,

or the warranty will be voided on these parts.

• Cover the sink drain to avoid losing parts.

PRODUCT SPECIFICATIONS

SPECIFICATIONS SPECIFICATIONS

Ceramic cartridges

ASME A112.18.1/CSA B125

Manufactured to include no more than 0.25% weighted average lead

content on wetted surfaces

ANSI/NSF 61-9

1 or 3-hole installation - optional deck plate and side spray not included

MODELS

547695-Polished chrome

547737-Brush nickel

547620-Polished chrome

547638-Satined nickel

www.todaysdesignhouse.com

Polished chrome and Satined nickel finish

NSF/ANSI 372

Notes: The picture in this installation instructions is for reference

only, pls refer to actual product in installation process.

www.todaysdesignhouse.com

1. Turn off water under sink.

Remove old faucet making sure

not to damage water lines.

Insert spray hose down through

hole in spray holder. Attach

lower end of spray hose to

entral supply tube in faucet.

2. Install the spout through top of

sink. From underneath the sink,

replace the rubber seal, metal

washer and lock nut. Tighten the

screws on the lock nut to secure

the body.

6. Tighten end of shank with

wrench and slip coupling nut

onto inlet port.

Insert optional spray holder

through the hole in sink.Screw

lock nut to shank and tighten.

7. After installing faucet, remove

aerator and turn on water to

remove any debris.

Re-assemble aerator.

ASSEMBLY INSTRUCTIONS

Screw spray head onto spray

hose.

Summary of content (2 pages)

PAGE 1
Design House is a registered brand of DHI Corp.Mequon,WI 53092 1-800-558-8700 ASSEMBLY INSTRUCTIONS 1. Turn off water under sink. Remove old faucet making sure not to damage water lines. 1 2. Install the spout through top of sink. From underneath the sink, replace the rubber seal, metal washer and lock nut. Tighten the screws on the lock nut to secure the body. 2 3. Insert optional spray holder through the hole in sink.Screw lock nut to shank and tighten. 3 4. Screw spray head onto spray hose.
PAGE 2
CARE AND MAINTENANCE LIMITED LIFETIME WARRANTY Clean peridodically with a soft cloth.Avoid abraisive cleaners,steel wool, and harsh chemicals as these will dull the finish and void your warranty TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Leaks underneath handle 1.Shut off the water supply to the faucet that leaks. Bonnet has come loose or O-ring on cartridge is 2.Remove the handle on the problem side. Loosen the bonnet by dirty or twisted. turning it counterclockwise.