Instructions / Assembly

ManualsBrandsDesign House ManualsBathMiddleton 4 in. Centerset Single-Handle Bathroom Faucet in Oil Rubbed Bronze

MIDDLETON SINGLE HANDLE

LAVATORY FAUCET

Models 584011, 584029

Your new Design House faucet will give you years of trouble free performance. Thank you for

choosing our product for your home. Please read all of these instructions carefully before

installing your new faucet.

When installing your new faucet, hand tighten the connector nuts, then use one wrench to

anchor the fitting and a second wrench to tighten the nut one additional turn. Connections that

are too tight will reduce the integrity of the system.

Wrap threaded connections (except aerator thread in s

pout or where o-ring or rubber sealant

are present) with Teflon tape available from your local hardware or plumbing supply store.

Always wrap in a clockwise direction.

IMPORTANT POINTS

SAFETY TIPS

ALWAYS protect your eyes with safety glasses.

Helpful tools to install this faucet:

Teflon tape

(2) crescent wrenches

basin wrench

flashlight

faucet supply tubes

silicon sealer

INSTALLATION PROCEDURE

1. Shut off water supplies. Remove the

old faucet. Place the faucet assembly

through the mounting holes in sink.

Secure the faucet assembly to sink

using the washers (1A) and nuts (1B)

provided.

Note: If the sink is uneven, use silicone

under the putty guard (1C).

2. Making the waterline connections:

Use 1/2 in. I.P.S. faucet connections

(2B, not included), or use the supplied

coupling nuts (2C) with a 3/8 in. O.D.

ball-nose riser (2A, not included).

Before tightening the faucet connec

tor

to the water supply, apply a second

wrench to the supply tube fitting. This

will prevent the supply tube from

moving or twisting when tightening the

faucet connector. Do not overtighten.

3. IMPORTANT: After installation is

complete, remove the aerator to flush the

water lines. Do not lose the gasket (3A) in

the aerator. Turn on the water supply and

allow both hot and cold water to run for at

least one minute each. This flushes away

any debris that could cause damage to

internal parts. While the water is

running,

check for leaks. Turn off the water and

replace the aerator.

1-800-558-8700

Mequon, WI 53092

Design House is a registered

brand of DHI Corp.

MAINTENANCE

Brass finishes are polished, then protected with a PVD or a lacquer coating to help prevent tarnishing.

Clean these surfaces only with a damp, soft cloth.

Your new Design House faucet is designed to give you years of trouble free performance. Avoid abrasive

cleaners, steel wool and harsh chemicals that will dull the finish and void your warranty.

CONSUMER PROTECTION WARNING

To reduce the amount of lead in your drinking water, allow the water to run for a moment before

filling your glass and remember to always use cold water for drinking purposes.

Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the

amount of lead used in brass and solder. Your new faucet is made in strict compliance with

all government standards. The materials used in the manufacture of this faucet are of industry

standard quality and are similar to other plumbing products having brass

fittings.

Keep it looking like new by cleaning it periodically with a mild solution of soapy water. Rinse thoroughly and

then dry with a soft cloth.

Summary of content (2 pages)

PAGE 1
Mequon, WI 53092 1-800-558-8700 Design House is a registered brand of DHI Corp. MIDDLETON SINGLE HANDLE LAVATORY FAUCET Models 584011, 584029 Your new Design House faucet will give you years of trouble free performance. Thank you for choosing our product for your home. Please read all of these instructions carefully before installing your new faucet.
PAGE 2
o o 584011 - Satin Nickel 584029 - Oil Rubbed Bronze Lift rod & Lift rod knob Stopper Flange Washer Gasket Washer Nut Washer Pivot Rod & Ball Body Pivot nut Clip Screw Strap Many of these parts come preassembled. This exploded diagram is to assist in trouble shooting. Action: 1. Unscrew the aerator. Make sure all internal parts are laying flat. 2. If there is debris, gently flush all parts inside. 3. Reinstall the aerator. Cause: Aerator is incorrectly fitted or is dirty.