Item # 310 499 512 Model # DS18691 USE AND CARE GUIDE FLOOR LAMP Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext. 216 For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.
Table of Contents Table of Contents............................................................ 2 Safety Information.......................................................... 2 Warranty........................................................................... 2 One (1) Year Warranty.................................................................. 2 What is Covered.......................................................................... 2 What is Not Covered................................................
Pre-Assembly PLANNING ASSEMBLY Read all instructions before assembly. To avoid damaging this product, place it on a soft, non-abrasive surface, such as carpet or cardboard. IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please call the Customer Service Team at 1-800-388-6141 ext. 216.
Assembly 1 2 Connecting the lower tube to the base □□ Pull the excess power cord (H) through the base (G). Connecting the remaining tubes □□ Pull the excess power cord (H) through the base (G). □□ Tighten the lower tube (F) onto the base (G). □□ Tighten the middle tube (E) onto the lower tube (F). □□ Tighten the upper tube (D) onto the middle tube (E). NOTE: Do not twist the power cord (H). NOTE: Do not twist the power cord (H). Be careful to match the thread between the connector and pole.
Assembly (continued) 3 4 Connecting the socket assembly to the upper tube □□ Pull the excess power cord (H) through the base (G). Installing the glass shade □□ Unscrew the socket ring (A) from the socket assembly (C), and place the glass shade (B) onto the socket assembly (C). Replace and tighten the socket ring (A). □□ Tighten the socket assembly (C) onto the upper tube (D). NOTE: Do not twist the power cord (H).
Care and Cleaning □□ Use a dry, soft cloth to dust or wipe carefully. □□ Do not clean with abrasive materials, bleach, or solvents. Troubleshooting Problem Possible Cause Solution The lights will not turn on. The bulb is burned out. The power is off. The cord is not plugged in. Replace the light bulb. Ensure the power supply is turned on. Ensure the cord is plugged into an outlet. The circuit breaker is off. There is an exposed wire. Ensure the circuit breaker is set in the “ON” position.
Service Parts MODEL: DS18691 A B C D E F G H Part A Description Socket ring B C D Glass shade Socket assembly Upper tube Part E F G H (Pre-assembled on the socket assembly (C)) 7 Description Middle tube Lower tube Base Power cord
Questions, problems, missing parts? Before returning to the store, call Design Solutions International Customer Service Mon-Fri 9:30 am to 3:00 pm EST 1-800-388-6141 ext. 216 For customer service support and the fastest response, please email us at CustomerSupport@DSILighting.com Retain this manual for future use.
Artículo núm. 310 499 512 Modelo núm. DS18691 GUÍA DE USO Y MANTENIMIENTO LÁMPARA DE PIE ¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solutions International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext. 216 Para obtener ayuda de nuestro Servicio de atención al cliente y la respuesta más rápida, envíenos un correo electrónico a CustomerSupport@DSILighting.
Tabla de contenidos Tabla de contenidos........................................................ 2 Información de seguridad.............................................. 2 Garantía........................................................................... 2 Garantía de un (1) año................................................................ 2 ¿Qué cubre? .............................................................................. 2 ¿Qué no cubre? ..........................................................
Premontaje PLANIFICACIÓN DEL MONTAJE Lea las instrucciones antes de comenzar el montaje. Para evitar dañar este producto, colóquelo sobre una superficie suave, no abrasiva, como una alfombra o un cartón. OBSERVACIÓN: Puede utilizar una bombilla de base media (E26) de 100 W como máximo de 3 vías de tipo “A”, o bien una bombilla LED de 3 vías con balasto propio de base media (E26) de 16 W como máximo (se venden por separado).
Montaje 1 2 Conexión del tubo inferior a la base □□ Tire del cable de alimentación sobrante (H) a través de la base (G). Conexión de los tubos restantes □□ Tire del cable de alimentación sobrante (H) a través de la base (G). □□ Apriete el tubo medio (E) al tubo inferior (F). □□ Apriete el tubo inferior (F) a la base (G). □□ Apriete el tubo superior (D) al tubo medio (E) OBSERVACIÓN: No retuerza el cable de alimentación(H). OBSERVACIÓN: No retuerza el cable de alimentación(H).
Montaje (continuación) 3 4 Conexión del conjunto del casquillo al tubo superior □□ Tire del cable de alimentación sobrante (H) a través de la base (G). Instalación de la pantalla de cristal □□ Desenrosque la anilla del casquillo (A) del conjunto del casquillo (C) y coloque la pantalla de cristal (B) en el conjunto del casquillo (C). Vuelva a colocar y a enroscar la anilla del casquillo (A). □□ Apriete el conjunto del casquillo (C) al tubo ajustable (D).
Mantenimiento y limpieza □□ Utilice un paño seco y suave para quitar el polvo o limpiar con cuidado. □□ No limpie con materiales corrosivos, lejía o solventes. Reparación de averías Problema Las luces no se encenderán. Posible causa La bombilla está quemada. La alimentación está apagada. El cable de alimentación no está conectado. El disyuntor está apagado. El fusible se quema o se activa el disyuntor cuando se enciende la luz. Hay un cable expuesto. Solución Sustituya la bombilla.
Piezas de repuesto MODELO: DS18691 A B C D E F G H Pieza A Descripción Anilla del casquillo B C D Pantalla de cristal Conjunto del casquillo Tubo superior Pieza E F G H (preinstalada en el conjunto del casquillo (C)) 7 Descripción Tubo medio Tubo inferior Base Cable de alimentación
¿Tiene alguna pregunta o algún problema? ¿Le faltan piezas? Antes de volver a la tienda, llame al Servicio de atención al cliente de Design Solutions International De lunes a viernes, de 9.30 a 15 h EST 1-800-388-6141 ext. 216 Para obtener ayuda de nuestro Servicio de atención al cliente y la respuesta más rápida, envíenos un correo electrónico a CustomerSupport@DSILighting.com Conserve este manual para futuras consultas.