RFD OVEN SERIES WITH PROTOCOL 3TM CONTROLLER OWNER’S MANUAL C-250 PN 320253 VERSION 1 11/2012
RFD Oven Series Owner’s Manual Version 1 PREFACE 2 Revision History Revision 1 Date 11/2012 Author Livingston Description Format changes and revised for Protocol 3. Copyright © 2012 by Despatch Industries. All rights reserved.
RFD Oven Series Owner’s Manual Version 1 Table of Contents 1. About This Manual ............................................................................................................. 6 1.1. Important User Information ..................................................................................... 6 1.2. Manufacturer & Service .......................................................................................... 7 1.3. Organization of this Manual .............................................
RFD Oven Series Owner’s Manual Version 1 PREFACE 4 6. 7. 8. 5.3.1. Check Fan Rotation and Other Preliminaries ........................................................ 28 5.3.2. Start and Operate the Oven................................................................................... 29 5.3.3. Shutdown ............................................................................................................... 29 5.3.4. Working with Protocol 3 Operating Modes .......................................
RFD Oven Series Owner’s Manual Version 1 Figure 21. RFD2-13-2E, 480V (Drawing 320223-01). ................................................................. 42 Figure 22. RFD2-13-2E, 480V (Drawing 320223-02). ................................................................. 42 Figure 23. RFD2-13-2E Oven Assembly (Drawing 148457-01). ................................................. 42 Figure 24. RFD2-19-2E, 208V (Drawing 320228-01). .................................................................
RFD Oven Series Owner’s Manual Version 1 ABOUT THIS MANUAL 6 1. About This Manual 1.1. Important User Information Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 ABOUT THIS MANUAL 7 Danger! Only fully-trained and qualified personnel should setup and maintain this equipment. Improper setup and operation of this equipment could cause an explosion that may result in equipment damage, personal injury or possible death. The information in this document is not intended to cover all possible conditions and situations that might occur.
RFD Oven Series Owner’s Manual Version 1 ABOUT THIS MANUAL 8 Danger! Failure to heed warnings in this instruction manual and on the oven could result in personal injury, property damage or death. 1.4. Conventions This icon signifies information that describes an unsafe condition that may result in death, serious injury, or damage to the equipment. Danger is the signal word used to indicate a hazardous situation that, if not avoided, will result in death or severe injury.
RFD Oven Series Owner’s Manual Version 1 ABOUT THIS MANUAL 9 1.5.2. Capacities Capacity Maximum load capacity (Lbs) (Kg) Maximum shelf capacity (Lbs) (Kg) Exhaust capacity (min/max) (CFM) (Lps) Recirculating fan (HP) (CFM) (Lps) Net weight (Approximate) (Lbs) (Kg) Shipping weight (Approximate) (Lbs) (Kg) Solvent Handling Capabilities M.E.K. or equivalent at 177ºC (350ºF) (GPH) (LPH) Forced Exhaust (HP) Model RFD2-13 Model RFD2-19 Model RFD 2-35 850 386 850 386 1250 567 100 45.4 100 45.4 100 45.
RFD Oven Series Owner’s Manual Version 1 ABOUT THIS MANUAL 10 1.5.3. Temperatures Feature Range Maximum Operating Temperature (°C) (°F) 40°C – 177°C Time to Temperature 40°C – 260°C (No Load) 40°C – 343°C 177 350 Temperature * 260 Uniformity at 500 (ºC) (ºF) 343 650 Minimum Operating Temperature Above Ambient* (ºC) (ºF) Control Stability (∆ represents the change in ambient temperature) (ºC) Model RFD 2-13 Model RFD 2-19 Model RFD 2-35 15 28 45 343 650 16 30 48 12 22 36 +/-2 +/-4 +/-2.
RFD Oven Series Owner’s Manual Version 1 ABOUT THIS MANUAL 11 1.5.4. Power Line voltages may vary in some geographies. If the line voltage for your RFD oven varies more than 10% from the oven voltage rating, electrical components such as relays and temperature controls may operate erratically.
RFD Oven Series Owner’s Manual Version 1 ABOUT THIS MANUAL 12 1.5.5. Capability The RFD oven is specifically designed for Class A NFPA 86 requirements, in which flammable solvents are present. They include a pressure relief panel, purge timer and exhaust fan. Please note the solvent handling capabilities and do not exceed. Danger! Class A ovens are designed for a specific amount of solvent. Exceeding this amount could result in an explosion. Refer to Design Specification Label (Figure 14) or Section 1.
RFD Oven Series Owner’s Manual Version 1 2. Safety 2.1. Safety Information Do not work on the RFD oven without reading and understanding this section which contains important information and warnings. Ignoring these warnings can result in death, serious injury or damage to the machine and product. 2.1.1. Lockout Machine lockout places the RFD oven into a zero energy state and prevents accidental machine start up.
RFD Oven Series Owner’s Manual Version 1 SAFETY 14 2.2. Maintenance Only qualified and trained personnel should perform maintenance or repair. 2.3. Electrical Power Only qualified and trained personnel should perform electrical maintenance or electrical repair. Danger! High voltage present on this equipment, service by authorized personnel only. Contact with energized electrical sources may result in serious injury or death.
RFD Oven Series Owner’s Manual Version 1 SAFETY 15 2.5.1. Optional Disconnect Switch The RFD oven has an optional Disconnect Switch (Figure 3). This Disconnect Switch is connected to the load break switch behind the panel that disconnects or connects power from the main line. When a risk of personal injury or damage to the RFD oven exists, turn OFF the DISCONNECT SWITCH on the front of the oven. This shuts off all electrical power to the oven. Figure 3. Disconnect Switch.
RFD Oven Series Owner’s Manual Version 1 THEORY OF OPERATION 16 3. Theory of Operation 3.1. The RFD Oven Series Despatch RFD ovens feature horizontal recirculating airflow to ensure exceptional temperature uniformity throughout the oven. A high-volume fan circulates air through perforated, stainless steel walls to create a constant horizontal airflow across all sections of the oven.
RFD Oven Series Owner’s Manual Version 1 THEORY OF OPERATION 17 3.2. Damper Control The RFD Series oven includes a manually adjustable fresh air damper mechanism which controls the flow of fresh air into the chamber. The fresh air damper control is located on the left side of the oven (Figure 5 and Figure 6). The oven also includes a manually adjustable exhaust damper located on the exhaust stack on top of the oven (Figure 6).
RFD Oven Series Owner’s Manual Version 1 THEORY OF OPERATION 18 3.2.1. Determining Damper Settings The optimum setting for the amount of fresh air that should be distributed into the chamber depends on several factors. These factors include ambient environment temperature, load conditions, load distribution, heat-up rates, cool-down rates, desired temperature uniformity and, most importantly, the desired operating temperature.
RFD Oven Series Owner’s Manual Version 1 THEORY OF OPERATION 19 3.3. Optional Adjustable Louvers This section applies only to ovens that include the optional adjustable louvers. Ovens without the louver option do not have adjustable airflow. RFD oven series come standard with perforated supply and exhaust panels (Figure 7). Optional adjustable louvers provide an extra measure of airflow customization (Figure 7). Figure 7 shows the initial factory settings for the optional louvers.
RFD Oven Series Owner’s Manual Version 1 THEORY OF OPERATION 20 3.3.1. Purpose of Adjustable Airflow Optional adjustable airflow has several purposes in the RFD oven: 1. Ability to get the best temperature and airflow uniformity. 2. Ability to “spot heat” special areas or specific parts of load. 3. Ability to prevent air flowing out or sucking in through the entrance and exit openings in the oven. 3.3.2.
RFD Oven Series Owner’s Manual Version 1 THEORY OF OPERATION 21 controller/High Limit instrument. The control portion utilizes a time proportioning voltage signal to control heating devices with minimal temperature fluctuations. The High Limit portion protects the product and/or the oven from overheating. If the product being processed has a critical high temperature limit, the High Limit setpoint should be set to a temperature somewhat below the temperature at which the product could be damaged.
RFD Oven Series Owner’s Manual Version 1 THEORY OF OPERATION 22 3.5. Optional High Limit Audible Alarm High Limit audible and visual alarm is a red light (Figure 13) and small alarm horn located on the front of the control panel. The alarm is sounded if a High Limit condition occurs. A switch is provided to silence the alarm. This alarm has a range of 80dB at 2 ft (0.6 m). 3.6.
RFD Oven Series Owner’s Manual Version 1 4. ASSEMBLY & SETUP 23 Assembly & Setup Assembly and Setup provides directions for unpacking and installing your RFD oven. Danger! This equipment must be installed by a licensed electrician who is experienced with combustion safeguard control systems and understands the functions of an interlocking switch such as gas pressure switches.
RFD Oven Series Owner’s Manual Version 1 ASSEMBLY & SETUP 24 Warning! Do not use the oven in wet, corrosive or explosive atmospheres unless this oven is specifically designed for a special atmosphere. Notice 4.2.1.1. Review oven weight to ensure the foundation is adequate to hold the weight. Placement Requirements Place oven directly on the floor. Allow adequate clearance for explosion relief. Minimum clearance for explosion relief is 18 in. above the oven.
RFD Oven Series Owner’s Manual Version 1 Notice ASSEMBLY & SETUP 25 Flashing through roof or wall must be capable of handling temperatures up to 343°C (650°F). All stacks must comply with state and local building codes to ensure that surrounding combustible surfaces are below 71°C (160°F). 4.4. Wiring & Power Connections See electrical schematics in Section 8.3 for line connections. The oven must be hardwired directly to the electric supply.
RFD Oven Series Owner’s Manual Version 1 OPERATION 26 5. Operation Users and operators of this oven must comply with operating procedures and training of operating personnel as required by the Occupational Safety and Health Act (OSHA) of 1970, Section 5 and relevant safety standards, and other safety rules and regulations of state and local governments. Refer to the relevant safety standards in OSHA and National Fire Protection Association (NFPA), Section 86 of 1985.
RFD Oven Series Owner’s Manual Version 1 OPERATION 27 Caution! Always place loads on the shelves provided to avoid possible uneven heating and damage to the oven. The two shelves are designed to be pulled out about halfway without tipping. Do not overload the shelves. Shelf support capacity is listed in the Capacities section (1.5.2). Do not overfill the oven. Distribute the workload evenly so airflow is not restricted.
RFD Oven Series Owner’s Manual Version 1 OPERATION 28 5.3. Operating Procedure 5.3.1. Check Fan Rotation and Other Preliminaries If polarity is reversed during wiring, the fan will rotate backwards and compromise proper ventilation. 1. Check fan rotation after the initial installation and after reconnecting the power supply to ensure the fans are running in the correct direction. To check fan rotation: a. Momentarily toggle POWER (Figure 13) to start fans and check rotation. b.
RFD Oven Series Owner’s Manual Version 1 OPERATION 29 Never operate oven at a temperature above the maximum operating temperature: 343°C (650°F) 5.3.2. Start and Operate the Oven 1. Set the main Power Disconnect switch to ON (Figure 3). 2. Set POWER to ON. The recirculation fan will start, and the purge timer will begin timing. Notice The heater of the Class A oven cannot be energized until the forced exhaust system has brought in a minimum amount of fresh air into the chamber.
RFD Oven Series Owner’s Manual Version 1 OPERATION 30 If additional information is required regarding the operation of this equipment, please contact Despatch. Global Headquarters Contact Despatch Industries 8860 207th Street Lakeville, MN 55044 USA International/Main: 1-952-469-5424 US toll free: 1-888-337-7282 Fax: 1-952-469-4513 info@despatch.com www.despatch.com Service & Technical Support Service: 1-952-469-8230 US toll free: 1-800-473-7373 Service @despatch.com 5.3.4.
RFD Oven Series Owner’s Manual Version 1 6. MAINTENANCE 31 Maintenance Do not attempt any service on this oven before setting the main power Disconnect Switch to OFF. Danger! Disconnect all power sources before making repairs. Contact with energized electrical sources may result in serious injury or death. 6.1. Checklist Keep equipment clean. Gradual dirt accumulation retards airflow.
RFD Oven Series Owner’s Manual Version 1 MAINTENANCE 32 6.2. Maintenance Schedule Preventive Maintenance (Refer to Section) Daily Weekly Monthly Every Three Months Every Six Months Annually As Needed General Avoid placing load too close to supply duct (5.1) Visually inspect for dirt, debris and free movement of parts and controls. X X Clean as needed X Inspect door seals for proper seating, damage and/or tears Inspect door operation.
RFD Oven Series Owner’s Manual Version 1 MAINTENANCE 33 Preventive Maintenance (Refer to Section) Daily Weekly Monthly Check High limit controller (6.8) Verify purge timer setting (6.4) Every Three Months Every Six Months Annually As Needed X X 6.3. Check Fans Check fan operation by closely observing for abnormal movement or sound. Irregular noise or movement may mean the fan needs repair or replacement. Listen for any irregular noises coming from the fans. 6.4.
RFD Oven Series Owner’s Manual Version 1 MAINTENANCE 34 2. Allow the oven to stabilize at its minimum operating temperature by leaving the heater off. 3. Set the oven power to OFF. 4. Verify that the white line in the indicator window of the airflow switch is OFF (Figure 15). a. If the switch remains ON, increase the airflow switch set point until the switch turns OFF. b. A switch setting of 0.2” WC (inches of water column) to 1.0” WC should detect a fan malfunction. c.
RFD Oven Series Owner’s Manual Version 1 MAINTENANCE 35 Remove the hex cap to gain access to the slotted setpoint adjustment Switch setpoint indicated by the top of the adjustment screw A switch setting of 0.2 in WC to 1.0 in WC should detect a fan malfunction Figure 16. Adjust the airflow switch. 6.6. Lubrication Lubricate all door latches, hinges, door operating mechanisms, and wear surfaces to ensure easy operation. 6.7.
RFD Oven Series Owner’s Manual Version 1 MAINTENANCE 36 6.9. Replacement Parts Danger! Do not attempt any service on this equipment without setting the main power Disconnect Switch to OFF. Disconnect all power sources before making repairs. Contact with energized electrical sources may result in serious injury or death. Contact the Service Products Division at Despatch to order or return parts. The Service Products features our Response Center for customer service.
RFD Oven Series Owner’s Manual Version 1 7. TROUBLESHOOTING 37 Troubleshooting 7.1. Troubleshooting: Possible Problems and Solutions Equipment which operates for long periods of time may develop problems. Table 3 lists possible problems and suggested solutions. If you have a problem not listed and do not know what to do, contact Despatch Industries at our toll free Help Line 800-473-7373. Table 3. Troubleshooting grid.
RFD Oven Series Owner’s Manual Version 1 TROUBLESHOOTING 38 Difficulty Excessive vibration Oven will not control at setpoint Heater does not shut down until temperature reaches the High Limit setting Probable Cause on fan shaft Unbalanced fan wheel Suggested Remedy wheel and inlet ring Replace fan wheel Dirty fan wheel Unbalanced fan wheel Clean fan Replace fan wheel High Limit set too low Set the High Limit higher.
RFD Oven Series Owner’s Manual Version 1 Conditions B. Cold by door C. Positive pressure in chamber D. Negative pressure in chamber 1. 2. 3. 4. 5. 6. 1. 2. 3. TROUBLESHOOTING 39 Actions 2. Check motor for proper operation and direction of rotation. See A-1. Check door seals. Open optional supply louvers close to door. Close fresh air damper. Open exhaust damper. Refer to Damper Control Section 3.2 for more information. Close exhaust damper. Open fresh air damper. Open optional supply louvers slightly.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 40 8. Appendices 8.1. Standard Products Warranty Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 41 8.2. MRC5000 Setup (Optional) Refer to instructions provided recorder manufacturer for more specific installation notes. Temperature is retransmitted to the MRC5000 recorder from the controller. Set up the recorder by: 1. Ensure hardware jumper JU1 is in place for the 5 VDC setting (Refer to MRC5000 Manual included). 2. Move MODE to PROG/TEST/CAL to display Prog. 3. Press ▼ twice to display Inps. Move to each Parameter Code using ▼or ▲.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 42 Figure 17. RFD2-13-2E, 208V (Drawing 320219-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 43 Figure 18. RFD2-13-2E, 208V (Drawing 320219-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 44 Figure 19. RFD2-13-2E, 240V (Drawing 320221-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 45 Figure 20. RFD2-13-2E, 240V (Drawing 320221-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 46 Figure 21. RFD2-13-2E, 480V (Drawing 320223-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 47 Figure 22. RFD2-13-2E, 480V (Drawing 320223-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 48 Figure 23. RFD2-13-2E Oven Assembly (Drawing 148457-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 49 Figure 24. RFD2-19-2E, 208V (Drawing 320228-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 50 Figure 25. RFD2-19-2E, 208V (Drawing 320228-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 51 Figure 26. RFD2-19-2E, 240V (Drawing 320230-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 52 Figure 27. RFD2-19-2E, 240V (Drawing 320230-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 53 Figure 28. RFD2-19-2E, 480V (Drawing 320232-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 54 Figure 29. RFD2-19-2E, 480V (Drawing 320232-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 55 Figure 30. RAD2-19-2E Oven Assembly (Drawing 162533-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 56 Figure 31. RFD2-35-2E, 208V (Drawing 320237-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 57 Figure 32. RFD2-35-2E. 208V (Drawing 320237-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 58 Figure 33. RFD2-35-2E, 240V (Drawing 320239-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 59 Figure 34. RFD2-35-2E, 240V (Drawing 320239-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 60 Figure 35. RFD2-35-2E, 480V (Drawing 320241-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 61 Figure 36. RFD2-35-2E, 480V (Drawing 320241-02). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Series Owner’s Manual Version 1 APPENDICES 62 Figure 37. RFD2-35-2E Oven Assembly (Drawing 148439-01). Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
RFD Oven Owner’s Manual Version 1 63 3rdDraft— Copyright © 2012 by Despatch Industries. All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.