LOG SPLITTER ASSEMBLY GUIDE MODEL: OPS240 40 TON KINETIC SPLITTER DETAIL K2 INC. DK2 POWER USA 4301 S Valley View Blvd STE 10-11 Las Vegas, NV 89103 1-702-331-5353 DETAIL K2, INC. 1080 Clay Avenue Unit 2 Burlington, Ontario, Canada L7L0A1 DK2 USA EAST 6245 Industrial Parkway Whitehouse, OH 43571 PARTS AND SERVICE 702-331-5353 OR WWW.DK2POWER.
STEP 1: Open and unpack all items. Leave lots of working space. Inspect all parts. The SPLITTER is shipped in a crate. Remove all sides before you begin. NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING PARTS PLEASE CALL DK2 POWER AT 702-331-5353 OR CONTACT US VIA OUR WEBSITE WWW.DK2POWER.
STEP 2: 1. Install cross frame and tow bar frame. 2. Use 4 bolt hardware included.
STEP 3: 1. Open the hood 2. Install the safety lock control handle. Screw it until tight into the locking casting.
STEP 4: 1. Install the split handle with hardware provided 2.
STEP 5: 1. INSTALL THE FOOT STAND 2. BOLT BOTTOM HOLE 3.
STEP 6: 1. INSTALL TOW BAR 2. Secure tight using hardware provided.
STEP 7: 1. Install the front table bracket as shown using the hardware provided. 2. KEEP LOOSE until after table installation to help with hole alignment.
STEP 8: 1. Install the wheels on the axel and insert spring pin. 2. Make sure wheel is free spinning. You can remove pin, slide wheel and re-pin to lock wheel during splitting.
STEP 9: 1. Get some help lifting the unit by the hitch and standing the unit upright resting on the back bottom plate. 2. Another option is use safely a hydraulic jack or lift chain. 3. BE CAREFUL THIS IS UNIT IS HEAVY AND SHOULD BE HANDLED BY MULTIPLE PERSONS OR A SAFE LIFTING DEVICE. 4.
STEP 10: 1. Assembly LOG CRADEL SLIDES to side of beam as shown. 2. Use hardware supplied and bolt both rail cradle assemblies together. 3. Tighten all bolts securely.
STEP 11: 1. Install the work table 2. Use the 8 flat bolts and hardware provided 3. Tighten the 2 bolts on the underside table supports that were left loose in previous assembly steps. 4. Recheck all assembly bolts and equipment bolts and tighten if required. Use 8 bolts provided CONGRATS – YOUR ALMOST DONE Grease the rack teeth and the spline with standard grease. Keep the log beam free of grease and keep clean when splitting.
REV 1 – 9-19-2019
Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Description Handle rubber sleeve Handle Upper hood clasp Small switch screw Work table Pully Protect the frame tube pulley under hood Pressing buckle Left arm guard Right arm guard Shock block Ejector pad Split head fitting Ring fixed block Rings Table front support plate Table back support plate Rubber cushion Compression spring(Ejector pad) Bearing pedestal Small switch transmission shaft Trigger Gear rod Beam Trigger pin Ref
READ THE KOHLER ENGINE MANUAL SUPPLIED WITH YOUR UNIT FOR FULL ENGINE OPERATION, SAFETY, AND MAINTENANCE. YOUR UNIT HAS A COMMERCIAL KOHLER ENGINE WITH A 3YR PARTS AND SERVICE WARRANTY. FOR WARRANTY IN YOUR AREA CONTACT THE NEAREST KOHLER DEALER. VISIT WWW.KOHLERENGINES.COM FOR PARTS, SERVICE, MANUALS, AND DEALER LOCATIONS.
OPERATION – BEFORE STARTING ENGINE CLEAR AREA OF ALL PEOPLE AND PROPERTY THAT COULD BE DAMAGED. THINK SAFETY. THIS SPLITTER IS FAST AND CAN CAUSE INJURY IF SAFETY IS NOT ENFORCED. ONLY ONE OPERATOR SHOULD WORK THIS UNIT. NEVER HAVE ANOTHER PERSON LOADING LOGS WHILE ANOTHER IS AT THE CONTROLS. DO NOT REMOVE THE SECOND HAND SAFETY LEVER. IF YOUR UNIT WILL NOT START – 1. CHECK THE OIL LEVEL. YOUR ENGINE HAS A LOW OIL SHUTOFF PROTECTION AND WILL NOT START IF LOW ON OIL. 2. MAKE SURE SPARK PLUG WIRE IS SEATED.
PLEASE DO NOT RETURN TO THE STORE YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE CALL US AT 702-331-5353 FOR FAST WARRANTY PARTS AND QUESTIONS WHAT IS COVERED DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing defects in workmanship and materials under normal use and service for a period of one (1) year from the date of the original purchase.