Model 880RA-N4X Model 880RS-N4X Graphic Remote Display Operator’s Installation and Instruction Manual DETCON, Inc. 3200 Research Forest Dr., A-1 The Woodlands, Texas 77381 Ph.281.367.4100 / Fax 281.298.2868 www.detcon.com September 11, 2009 • Document # 3489 • Revision 0.
880R-N4X Page intentionally blank 880R-N4X Instruction Manual ii
880R-N4X Table of Contents Introduction .............................................................................................................................................1 1.0 2.0 System Configuration .............................................................................................................................1 2.1 Touch Panel Graphic Display............................................................................................................... 1 2.2 Specifications ........
880R-N4X Figure 22 Channel Details Screen ...................................................................................................................... 13 Figure 23 Alarm History Screen......................................................................................................................... 14 Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.
880R-N4X 1.0 Introduction The Detcon Model 880 Remote Display unit is specifically designed to serve as a Remote Monitor for the Model 880 PLC Control Units. The Model 880RA-N4X is designed to work with the Model 880 Analog versions, and the Model 880RS-N4X is designed to work with the Model 880 Serial versions PLC Graphic Controllers. The NEMA 4X rated enclosure is rain tight and suitable for outdoor locations in electrically nonhazardous environments.
880R-N4X P1 F1 N J1 J2 1 2 3 4 5 6 + + 24V . . . . L1 NOT Used + Dedicated power supply recommended PWR CPU TxD RxD 1A I Ground VAC (L1) NEU (L2) TXD+ TXDRXD+ RXD0V O TERMINAL INPUT Figure 2 Unit overview 2.
880R-N4X 3.0 Installation The Detcon Model 880 Remote Display enclosure is rated NEMA 4X, which is rain tight and suitable for outdoor locations in electrically non-hazardous environments. The enclosure is equipped with four (4) wallmounting brackets for easy wall mount installations. Care should be given to prevent sharp objects from colliding with the touch screen. The screen can be cleaned with a mild detergent and a lint free cloth. Never use an abrasive cleaner on the display. 1.
80R-N4X TXD+ TXDRXD+ RXD0V 4. Connect the RS-422 Serial communications cable to the input terminal blocks inside the 880 Remote Display labeled “TERMINAL INPUT” as shown in (Figure 5). TERMINAL INPUT Figure 5 Remote RS-422 connections MAIN 880 INPUT TERMINAL TXD+ TXDRXD+ RXD0V REMOTE OUTPUT TXD+ TXDRXD+ RXD0V TXD+ TXDRXD+ RXD0V CUSTOMER SUPPLIED WIRING REMOTE DISPLAY Figure 6 Remote Interconnect Wiring 5.
880R-N4X 4.0 Setup The 880 Remote Display incorporates a Touch Screen Graphic Display Panel. A Stylus ‘Wand’ is provided for use with the touch screen display. Care should be given to prevent sharp objects from colliding with the touch screen display as damage to the display may cause the unit to become inoperative. The screen can be cleaned with a mild detergent and a lint free cloth. Never use an abrasive cleaner on the display. 4.
880R-N4X The display screen also contains a number of “buttons”. These “buttons” act as toggle switches that change state when activated by the wand. These buttons will indicate the change in state by some obvious means such as a change in color, name, or both (i.e., when changing the state of an alarm from ascending to descending the button will change from a blue button displaying “ASC” to a gray button displaying “DES”). 4.
880R-N4X Figure 12 Screen Settings From the “Setting” Screen, select the “Adjust Clock” button to adjust the clock (Figure 13) or the “Adjust Display” button to adjust the Display Screen (Figure 14). Figure 13 Clock Adjust Screen To adjust the Time and Date use the arrow keys. Once the correct time and date have been set, select “OK” to close the screen. Select “Main Menu” to exit the “Setting” screen, and select “Exit” to exit the Setup screens. To adjust the display use the arrow keys.
880R-N4X 4.3 880 Remote Display Setup The remote display must be setup to match the main 880. The screens are duplicates of the Main 880; therefore, the setup is accomplished in much the same manner as the main unit. If the 880 Remote Display is not set up to match the Main 880, the resulting displays will be inconsistent and erroneous. 1) From the “Main Screen” (Figure 15), enter the “System Configuration Screen” by touching the “System Configuration” box with the wand.
880R-N4X NOTE: The System Configuration Screens differ only slightly between the Analog and Serial units. Figure 17 Serial Configuration Screen 3) Use the wand to select the “FACILITY NAME” box. A keyboard will appear to allow input of the facility name (Figure 18). The facility name can be any alphanumeric string of no more than 40 characters. After the facility name has been entered, use the ‘ENTER’ key to transfer the string to the “System Configuration Screen”.
880R-N4X Figure 19 Inputting the number of channels 5) Select the “EXIT” box to exit the “System Configuration Screen” and return to the “Main Screen”. 6) The “Channel Description”, “Gas Type”, and the range decimal point must be setup in the Remote Display to match the information used to setup the Main 880. Sensor Range and Alarm information should not be altered at the Remote Display. (This information is transferred over from the Main 880).
880R-N4X b) Select “Gas Type”, and input the gas type of the sensor. (i.e., H2S, LEL, CO2, etc.) Up to 10 characters maximum. The “Gas Type” entered here must match the “Gas Type” entered at the Main 880. c) The Range of the sensor is transferred by the Main 880 and should not be changed in the Remote Display. However, the decimal point must be set for the range to be correctly displayed.
880R-N4X 5.0 System Operation The touch screen display serves as the graphic user interface to the system. Maneuvering through the system screens and accessing data fields is accomplished by touching the wand to the appropriate area, box, button, or key on the screen. The provided “wand” should be the only instrument used to activate the screen as other instruments may cause damage to the screen. 5.1 Main Screen The main screen is the default screen of the unit (Figure 21).
880R-N4X will go through an initialization of the drive and the “USB Out” button will change to green, displaying “USB Eject”. To eject the USB Drive, touch the button with the wand. When the button turns gray and displays “USB Out” it is safe to remove the USB Drive from the port. “Reset” will clear alarms that have been set as latching after the alarm condition has passed. This will only work when alarms have been set as “Latching”, and only after the alarm condition has been cleared.
880R-N4X 5.3 Alarm History Screen Figure 23 Alarm History Screen When alarms are initiated, the unit stores information about these alarms into memory. If a USB Drive is installed in the back of the display, this information is written onto the drive for permanent storage (USB Drive sold separately). The information can also be viewed on the “Alarm History Screen” by using the wand to select the “Alarm History” button on the Main Screen.
880R-N4X 6.0 Spare Parts Recommended spare parts list: Detcon Part # Description 360-205420-024 347-SSP000-00A 24VDC 40Watt Power supply Stylus ‘Wand’ for Touch Screen Display Include Detcon part number when ordering spare parts. The Touch Screen Graphic Display is programmed to match the Main 880 Unit. For display replacements, please contact Detcon. 7.0 Warranty All warranties are FOB the Detcon factory.
880R-N4X Appendix A Revision History Revision 0.0 0.1 Date 03/26/09 09/25/09 880R-N4X Instruction Manual Changes made Original Release. Change to Mounting Flanges and update figures. Rev. 0.
880R-N4X Appendix A Drawings and Diagrams 1. Remote Display Dimensional Overview 2. Remote Display With Z-Purge Dimensional Overview 3. Remote Display Component Layout 4. Remote Display with Z-Purge Component Layout 5. Remote Display Wiring Diagram 6. Remote Display with Z-Purge Wiring Diagram 7. 880 to Remote Display wiring 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
880R-N4X Page intentionally blank Shipping Address: 3200 A-1 Research Forest Dr., The Woodlands Texas 77381 Mailing Address: P.O. Box 8067, The Woodlands Texas 77387-8067 Phone: 888.367.4286, 281.367.4100 • Fax: 281.292.2860 • www.detcon.com • sales@detcon.com 880R-N4X Instruction Manual Rev. 0.
