Waist-High Digital Bariatric Scale Model 685X Series Owner’s Manual Model 6857DHR Model M d l 6855 Model 6855MHR
TABLE OF CONTENTS INTRODUCTION ......……………………………………………………………………………. SPECIFICATIONS ………………………………………………………………………………. UNPACKING INSTRUCTIONS …….………………………………………………………….. CARE AND CLEANING OF SCALE ………………………………………………………….. OPERATION 6855, 6855KGEU, 6855MHR, 6856, 6856KGEU, and 6856MHR …………………….. To Weigh ……………………………………………………………………….…………. Zero Weight Display ……………………………………………………………………… To Weigh and Calculate BMI …………………………………………………………… 6854DHR, 6854KGEUDHR, 6857DHR, and 6857KGEUDHR ……..…………………..
FCC COMPLIANCE STATEMENT This equipment generates uses, can radiate radio frequency, and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been designed within the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC rules to provide reasonable protection against such interference when operated in a commercial environment.
INTRODUCTION Thank you for purchasing our Waist-High Digital Bariatric Scale. It has been manufactured with quality and reliability and has been tested before leaving our factory to ensure accuracy and dependability for years to come. This manual is provided to guide you through the operation of your scale. Please read it thoroughly before attempting to operate your scale and keep it available for future reference.
855MHR 6854DHR / 6854KGEUDHR 2 6856MHR 6857DHR / 6857KGEUDHR 1930-M458-O1 Rev-G y Bariatric Waist-High 685X Series
SPECIFICATIONS 6855 6855MHR 6855KGEU OIML EC Class III 6856 6856MHR 6856KGEU OIML EC Class III Capacity: 600 lb x .2 lb or 300 kg x 0.1 kg 270 kg x .1 kg or (selectable) 350 kg x 0.2 kg 1000 lb x .2 lb or 300 kg x 0.1 kg 450 kg x .1 kg or (selectable) 350 kg x 0.2 kg Platform Size: 18” x 14” / 46 cm x 36 cm 24” x 24” / 61 cm x 61 cm Shipping Weight: 70 lb / 32 kg 85 lb / 39 kg Height Rod: 24" to 84" x 0.1 in (60 cm to 212 cm x 0.1 cm) Display: Six digits, Seven segments, 0.7 inches (17.
UNPACKING INSTRUCTIONS x Remove the staples or cut along the bottom of the carton. Lift the carton off the pallet. x Check for any damage incurred in shipping. If the scale has been damaged, place a claim with the carrier. It is the responsibility of the purchaser to file all claims for any damages or loss incurred during transit. Use the original carton and shipping material to return the scale. x Cut the packing straps securing the scale to the pallet.
OPERATION 6855, 6855KGEU, 6855MHR, 6856, 6856KGEU, and 6856MHR ALWAYS assist the patient in stepping on and off the scale platform to ensure they do not fall. NEVER leave a patient unattended while they are on the scale platform. Failure to maintain control of the patient at all times can result in severe injury to you and/or the patient. To Weigh 1. Set the scale on any hard, level, flat surface, or low-cut carpet. 2. Press the ON/OFF key to turn on the indicator. 3.
OPERATION, CONT. 6854DHR, 6854KGEUDHR, 6857DHR, and 6857KGEUDHR ALWAYS assist the patient in stepping on and off the scale platform to ensure they do not fall. NEVER leave a patient unattended while they are on the scale platform. Failure to maintain control of the patient at all times can result in severe injury to you and/or the patient. To Weigh 1. Set the scale on any hard, level, flat surface, or low-cut carpet. 2. Press the ON/OFF key to turn the indicator on. 3.
OPERATION, CONT. 6854DHR, 6854KGEUDHR, 6857DHR, or 6857KGEUDHR To Weigh and Calculate BMI Using Mechanical Height Rod or Entering Known Height 1. Press the ON/OFF key to turn the indicator on. 2. If required, press the ZERO key to zero weight display. 3. Perform tare operation if required.
MECHANICAL HEIGHT ROD INSTRUCTIONS Mechanical Height Rod Installation Before starting the installation, please unpack carefully and remove all plastic wrappings, foam fillers, and cardboard material. You should have the following components: Item Qty 1 2 3 4 5 1 1 1 4 2 Description (1) Detecto Mechanical Height Rod (MHR) (1) MHR Upper Bracket (1) MHR Lower Bracket (4) #10 x 3/4” Hex Head Sheet Metal Screws (brackets to column) (2) M4 x 0.
MECHANICAL HEIGHT ROD INSTRUCTIONS, CONT. Measuring Patient’s Height 1. Before beginning the patient height measurement, make sure the spoon is rotated to the horizontal position, and raised well above the patient's apparent height. 2. While holding the spoon horizontal and above the patient's head, assist the patient on the scale platform. 3. Carefully lower the spoon, while keeping it horizontal, until the spoon rests on the top of the patient’s head. NOTE: If the patient is shorter than 3' 9 1/4" (114.
DIGITAL HEIGHT ROD INSTRUCTIONS Digital Height Rod Installation Before starting the installation, please unpack carefully and remove all plastic wrappings, foam fillers, and cardboard material. You should have the following components: Item Qty 1 2 3 4 5 1 4 2 8 3 Description Detecto Digital Height Rod (DHR) #10 x 1/2” Hex Head Sheet Metal Screws (brackets to column) Mounting Brackets (2) M4 x 0.7 x 5 Phillips Drive Pan Head Machine Screws (height rod to brackets) Cable Clip 1.
DIGITAL HEIGHT ROD INSTRUCTIONS, CONT. Measuring Patient’s Height The digital height rod must be in the “starting position” (the inner sliding tube must be completely down inside the outer stationary tube and the headpiece folded flat against the stationary tube) before turning on the indicator. If it is not in the “starting position”, the error message . will be displayed. 1. Make sure the height rod is in the starting position. 2. Press the ON/OFF key to turn the indicator on. 3.
PART IDENTIFICATION 6855 Side View Indicator Alternate Mounting Configuration 12 1930-M458-O1 Rev-G y Bariatric Waist-High 685X Series
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT. 6855/6854DHR Parts List The following are used on ALL models: ITEM # QTY PART NUMBER DESCRIPTION 1 1 1930-D330-0A WEIGHBRIDGE ASSY 2 1 1930-C338-08 MAT W/ADHESIVE 3 6 6007-0034 HEX HEAD SCREW, 5/16-18 UNC-2A X 3/4” 4 6 6024-0050 LOCK WASHER, 5/16” 5 6 6013-0275 HEX NUT, 5/16-18 UNC-2B 6 1 1930-C143-0A HANDRAIL ASSEMBLY 9 4 6021-0665 MACHINE SCREW, #6-32 X .
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT.
PART IDENTIFICATION, CONT. 6856/6857DHR Parts List The following are used on ALL models: ITEM # QTY PART NUMBER DESCRIPTION 1 1 1930-D445-0A WEIGHBRIDGE ASSY 2 1 1930-C452-08 MAT W/ADHESIVE 3 6 6007-0034 HEX HEAD SCREW, 5/16-18 UNC-2A X 3/4” 4 6 6024-0050 LOCK WASHER, 5/16” 5 6 6013-0275 HEX NUT, 5/16-18 UNC-2B 6 1 1930-C450-0A HANDRAIL ASSEMBLY 9 4 6021-0665 MACHINE SCREW, #6-32 X .
STATEMENT OF LIMITED WARRANTY Detecto Scale warrants its equipment to be free from defects in material and workmanship as follows: Detecto warrants to the original purchaser only that it will repair or replace any part of equipment which is defective in material or workmanship for a period of two (2) years from date of shipment. Detecto shall be the sole judge of what constitutes a defect.
STATEMENT OF LIMITED WARRANTY Conditions Which Void Limited Warranty This warranty shall not apply to equipment which: A.) Has been tampered with, defaced, mishandled, or has had repairs and modifications not authorized by Detecto. B.) Has had serial number altered, defaced, or removed. C.) Has not been grounded according to Detecto’s recommended procedure. Freight Carrier Damage Claims for equipment damaged in transit must be referred to the freight carrier in accordance with freight carrier regulations.
Cardinal Scale Manufacturing Co. 102 E. Daugherty, Webb City, MO 64870 USA Ph: 417-673-4631 or 1-800-641-2008 Fax: 417-673-2153 Printed in USA Technical Support: 1-866-254-8261 E-mail: tech@cardet.
