MARINER MODEL WPS12 WATERPROOF DIGITAL PORTION SCALE OWNER’S MANUAL 8528-0409-0M Rev A 04/15 CARDINAL SCALE MFG. CO. PO BOX 151 x WEBB CITY, MO 64870 PH (417) 673-4631 x FAX (417) 673-5001 www.detectoscale.com Technical Support: Ph: 866-254-8261 y techsupport@cardet.
INTRODUCTION TABLE OF CONTENTS Thank you for purchasing our Detecto Model WPS12 Waterproof Digital Portion Scale. Installation …………………..……………….. Unpacking ……………………..………… Power Supply …………………..……….. Battery Pack …..………………..……….. Battery Charging ................................... Low Battery ……..…………..…………… Display Annunciators ………..…..…………. Key Functions ………………..…..…………. Operation …..………….…………………..… Configuration ………….…………………..… Gravity Compensation ……………….…….. Display Messages ………………..………….
2
INSTALLATION UNPACKING Before beginning installation of your scale, make certain the instrument has been received in good condition. When removing the scale from its packing, inspect it for signs of damage, such as exterior dents and scratches. Keep the carton and packing material for return shipment if it should become necessary. It is the responsibility of the purchaser to file all claims for any damages or loss incurred during transit. 1.
DISPLAY ANNUNCIATORS The annunciators are turned on to indicate that the scale display is in the mode corresponding to the annunciator label or that the status indicated by the label is active. The O annunciator is turned on when the weight display is stable. lb The lb annunciator is turned on to indicate that the displayed weight is in pounds. oz The oz annunciator is turned on to indicate that the displayed weight is in ounces.
KEY FUNCTIONS UNITS / 1. Press to change the weighing units to the alternate units of measurement (if selected during configuration of the scale). 2. Press and hold three (3) seconds to turn display back light on or off.- TARE 1. Press to reset the displayed weight to zero up to 100% of the scale capacity. ON/OFF 1. Press and release to turn on scale. 2. Press and release to turn the scale off.
OPERATION TURN THE SCALE ON Press the ON/OFF key to turn the scale on. The scale will display all display segments then change to zero weight. SELECT THE WEIGHING UNIT Press the UNITS key to alternate between the selected weighing units. NOTE: Multiple weighing units must be enabled during configuration for this function to be operational. WEIGH Place the item to be weighed on the scale tray. Scale will display item weight.
CONFIGURATION The Scale has been pre-configured at the factory and should not require configuration for use in most applications. In the event that the factory settings do not meet the requirements of your application, the following describes the steps to configure the scale. TO BEGIN CONFIGURATION: 1. Press the ON/OFF key to turn on the scale. 2. Press and hold the SET key for 3 seconds. When the display shows *4; , release the SET key to enter the Configuration mode. The display will change to show '0-; .
CONFIGURATION, CONT. GRAVITY COMPENSATION 1. With the display showing 9 < : To Enable the Gravity Compensation mode, press the SET key. The display will change to #0 (use the factory set value of 9.797). To Disable the Gravity Compensation mode, press the UNIT key. The display will change to # (use the value obtained from the factory Tech Support). 2. 3. 4. 5. Press the SET key again. The display will change to show 9 < . Press the UNIT key. The display will change to show 03 .
DISPLAY MESSAGES DISPLAY MEANING !6` Low battery indication ` E2 prom Error #!` Over capacity CARE AND MAINTENANCE The heart of the WPS12 Waterproof Digital Portion Scale is a precision load cell located in the center of the scale base. It will provide accurate operation indefinitely if protected against overload of scale capacity, dropping items on scale, or other extreme shock. x DO NOT use acetone, thinner or other volatile solvents for cleaning.
8
