Manual

ManualsBrandsDetex ManualsSafetyDelayed Egress With Magnetic Lock

P/N: 101815-1 (4-0)

P/N: 101810-1 (3-0)

Pushpad Wrap

Modular Fillerplate Subassembly

Centercase/Pushpad Modular SubAssembly

Delayed Egress

P/N: 104374-X

Parts Check List

V40

Endcap

P/N: 101822

2" Narrow Stile

Plastic Template

Strike Shim

Mortise

U.S. PATENT NUMBERS:

6009732

6205825B1

6532777B2

INTERNATIONAL PATENT NUMBER:

PCT6009732

Endcap Bracket

P/N: 102450-X

Electromagnetic Lock

* Note:

Parts listed above will vary

according to product

configuration.

*Narrow Stile "NS" option

See

Optional Accessories

For:

- Glass Bead Kit

- Sex Nuts

- Tamper Kit

- Double Door Strike Kit

- Key Stop Kit

-Narrow Stile Kit

Mortise cylinder not included with device.

Standard Yale type cam required.

Door Sign

P/N: ECL-395-X

P/N: 101844-X

9V Battery

P/N: PP-5567

Hex Nut

P/N: 100783

DETEX

FOR SPECIAL LOCKING ARRANGEMENT:

THIS PRODUCT MUST BE CONNECTED INTO A FIRE ALARM SYSTEM PER NFPA CODE OR OTHER

REGULATIONS SO THAT, IN THE EVENT OF FIRE, THE TIME DELAY WILL BE BYPASSED. CONTACT

YOUR LOCAL CODE AUTHORITY TO VERIFY COMPLIANCE WITH FIRE AND BUILDING CODES.

THE DELAYED EGRESS DEVICE SHOULD BE ROUTINELY CHECKED FOR PROPER OPERATION AND

COMPLIANCE WITH FIRE AND BUILDING CODES

Plastic Template

P/N: 103806-X

Use for ease of installation

S & R Fillerplate Subassembly

P/N: 105033-X

P/N: 104383-X

Detex Power Supply Catalog No: 90-800

(80-800 Battery back-up power supply available)

Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045

(830)629-2900 / 1-800-729-3839 / Fax (830)620-6711

E-MAIL: detex@detex.com INTERNET: www.detex.com

103182 June 3, 2010

INSTALLATION INSTRUCTIONS FOR DETEX VALUE SERIES® V40 EM DELAYED EGRESS RIM PANIC

HARDWARE, FV40 EM DELAYED EGRESS RIM FIRE EXIT HARDWARE AND "H" MODELS (HURRICANE)

P/N: 100212

P/N: 100234-1

P/N: 100088

Owner's Copy

P/N: 100481

Strike Shield

P/N: 100480

P/N: 101899

P/N: 100482

98 Strike *, P/N: 100855-1

Mortise Strike

Plastic Template

Standard

P/N: 101805-1

Mounting plate

Subassembly

P/N: 100696-1

99 Strike *, P/N: 100855-2

Non-Roller Strike Strike Shim

Centercase Cover

103182 Page 1

Summary of content (16 pages)

PAGE 1
03182 June 3, 2010 Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045 (830)629-2900 / 1-800-729-3839 / Fax (830)620-6711 E-MAIL: detex@detex.com INTERNET: www.detex.
PAGE 2
!!!CHECK BEFORE STARTING!!! Wide Stile (Surface Strike) Minimum door stile 4-1/2" (114 mm) Template drawings provide door and frame structural and dimensional specifications for door and frame preparation. Narrow Stile 2"(51mm) Door Stile requires Mortise strike Doors and frames with walls having a structural thickness (metal skin plus reinforcement, or solid wood) to engage less than (3) full screw threads, are considered unreinforced for hardware.
PAGE 3
Fastener Table Tap Wrench Drill Bit Comments Use Either Machine Screws, Sheetmetal Screws, or Sex Nuts Machine Screws Sheetmetal Screws Self-drilling Screws PPH #36 or 7/64 #6-32 x 3/8" PPH ----- #10-24 x 5/8" PPH #1/4-20 x 1/4" PPH ----- ----- #1/4-20 x 1" PPH #7 or 13/64" #1/4-20 Tap #6 x 1" PFH #10 x 1" PFH #14 x 1-1/2" Sex Nut #6-32 Tap #6-32 x 5/8" #1/4-20 #10-32 Used on 98 Strike Shield Mounting Holes ----- #25 or 9/64" Used to Mount Centercase Cover and Endcap #10-24
PAGE 4
Mounting plate hole 2 3 Strike holes Mounting plate Hole Slide 99 strike locator into mounting plate. 1 (if using a 98 strike, see 98 STRIKE INSTALLATION page) If necessary, remove label temporarily to mark trim hole Mark mounting plate and strike holes 4 Punch marked holes 5 Trim input hole if necessary. (see outside trim instructions) RECOMMENDED Mark centerline for unit 40 inches above finished floor Mounting plate holes (2) For 1/4-20 machine screws drill #7 holes.
PAGE 5
Position cam as shown Insert centercase into slots of centercase mounting plate, depress pushpad, rotate toward door. DOOR 1 2 Fasten rim device to mounting plate with 1/4-20 x 1/4" PPH MUST BE INSTALLED! Peel off backing to expose tape. 3 Install Pushpad Wrap. Verify wrap is secured by snapping in place. IMPORTANT: 103182 Page 5 When using Pushpad Wrap with text verify handing before installing wrap.
PAGE 6
CHECKING FOR DEVICE CLEARANCE (Cut-Off procedure if required) Slide endcap assembly onto extrusion Align fillerplate FLUSH to extrusion prior to cutting 2 1 Secure with tape Max Cut-Off Type Electrified Model CAUTION: Check device and door frame clearance.
PAGE 7
2 1 Level pushpad assembly. Note: Endcap Bracket must bottom-out on extrusion. DO NOT REMOVE NYLON SPACER ON BACK OF BRACKET! With pushpad assembly level, secure the endcap bracket to door by tightening the factory installed self-drilling screw. 3 For 1/4-20 machine screws drill #7 holes. For #14 self-drilling screws no pilot holes necessary. For sex nuts drill 3/8" holes.
PAGE 8
For Hurricane Models Refer to electromagnetic lock instructions after step 4 below. (packaged with electromagnetic lock) (see Hurricane kit) Protect wires 1 Fasten rim device to mounting plate and door with 1/4-20x1" machine screws(drill #7 holes) or #14 self-drilling screws 2 5 Align the 99 strike with the latchbolt.
PAGE 9
EM ELECTRICAL OPTION REQUIRES DETEX POWER SUPPLY REQUIRED WIRE SIZES: STRANDED WIRE GAUGE: 18 AWG MIN MAXIMUM LENGTH OF TWO CONDUCTOR CABLE: 40 FEET Power Supply with Detex Delayed Egress device WHITE BLACK GREEN RED BLACK RED BLACK DETEX REQUIRES THE POWER SUPPLY BE LOCATED WITHIN 40 FEET OF THE DEVICE Detex requires one fire alarm relay per power supply Closed Fire Alarm Loop (must be supplied) To Exit Device Door #2 (if req'd) Fire Loop Sense To Exit Device Door #1 From (+) terminal to pin #1 on e
PAGE 10
Factory installed jumper 1 2 EM ELECTRICAL OPTIONS L9= Less 9V battery SI= Status Indicator POWER REQUIREMENT: .4 AMPS @ 24 VDC WIRING DIAGRAM A The key cylinder arming switch must be set to "OFF". To prevent the alarm from sounding during installation, attach battery AFTER main power is applied. Delayed Egress Device requires a connection to the Fire Alarm System. The fire alarm connection needs to be made Externally at the Power Supply.
PAGE 11
RISER DIAGRAM DETEX FILTERED AND REGULATED POWER SUPPLY WITH FIRE ALARM SYSTEM LOOP 24 VDC @1 AMP MIN DETEX REQUIRES THE POWER SUPPLY BE LOCATED WITHIN 40 FEET OF THE DEVICE PROVIDE WIRING CONDUIT, CONNECTOR, ETC BETWEEN DETEX POWER SUPPLY AND FIRE ALARM CONTROL PANEL AS REQUIRED TO ALLOW THE FIRE ALARM SYSTEM TO OVERRIDE THE DETEX DELAYED EGRESS FEATURE DURING A FIRE ALARM DETEX MAG LOCK SUPPLIED WITH DETEX DELAYED EGRESS PANIC HARDWARE J THE LOSS OF POWER OR OPEN FIRE ALARM CIRCUIT WILL ELIMINATE THE
PAGE 12
Value Series Flex Conduit/End Cap Kit (included) p/n: FCV VALUE SERIES FLEX CONDUIT INSTALLATION 2 1 Adjust for handing (LHR shown) 3 4 Fasten until hand-tight Drill 7/8" hole through center guide From magnet terminals Note: For high traffic areas an electric through-wire hinge or power transfer is recommended.
PAGE 13
DELAYED EGRESS OPERATIONS Deadlatch Home Key Position PushPad For BENCH TESTING: push and hold deadlatch while performing alarm test operations Mortise Cylinder (LHR shown) Red LED Siren Green LED ARMING AND AUTHORIZED EXIT With door closed, insert key in the cylinder, turn CCW then back to the home key position and remove it. LED glows green. Authorized personnel can exit the door during this rearm cycle.
PAGE 14
Problem TROUBLESHOOTING Probable cause Alarm sounds immediately when power is applied: Make sure the key cylinder arming switch is set to 'OFF'. No green light when key is turned CCW: Confirm strike is pushing in dead latch, door must be closed. Confirm 24VDC power on the delayed egress device main board terminals 1(+) & 2(-). Confirm closed fire loop connection on power supply. Confirm the two black wires on the center case are plugged into the 2-pin header on the center case circuit board.
PAGE 15
98 STRIKE INSTALLATION 98 Strike Locator (when required) Align the strike with the latchbolt. Firmly tighten screws Shield (if necessary) Door frame Shim (if necessary) 98 Strike Cutout per 98 strike Mark and drill holes as necessary. #7 for 1/4-20 machine screws, For #14 self-drilling screws, no pilot hole necessary.
PAGE 16
Optional Accessories Glass Bead Kit Catalog No: GB2 - Glass Bead Kit, 40 series p/n: 101644 #1/4-20 X 1-1/2" Screw (4) Included Sex Nut The #10-32 kit is available in (4) finishes: The #1/4-20 kit is available in (4) finishes: Catalog No: SN2 Catalog No: SN2 Catalog No: SN2 Catalog No: SN2 Catalog No: SN1 Catalog No: SN1 Catalog No: SN1 Catalog No: SN1 Brushed Brass BHMA 606 Finish Oil Rubbed Bronze BHMA 613 Finish Brushed Chrome BHMA 626 Finish Stainless Steel BHMA 630 Finish p/n: 101617-X p/n: 1