Instruction manual Congratulations Instruction manual We congratulate you on your new caravan and would like to thank you for choosing a quality product from Dethleffs.
Instruction manual Caravan - 11-06 - DET-0030-05 EN
Contents 1 Guarantee . . . . . . . . . . . . . . . . . . . . . 7 1.1 1.2 1.3 1.4 Guarantee certificate. . . . . . . . . . . . . . . 7 Guarantee conditions . . . . . . . . . . . . . . 8 Inspection records. . . . . . . . . . . . . . . . . 9 Inspection plan for annual inspection . . . . . . . . . . . . . . . . . . . . . . 12 Inspection plan for water ingress test . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 1.5 6.4 6.5 6.6 6.7 Entrance step (free-standing) . . . . . . .
Contents 7.12.3 7.12.6 Round seating group with round table . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Widening the bed into a playing area (variant 1). . . . . . . . . . . . . . . . . . . 75 Widening the bed into a playing area (variant 2). . . . . . . . . . . . . . . . . . . 76 Seating group with two single beds . . . 77 8 Gas system . . . . . . . . . . . . . . . . . . . 79 8.1 8.2 8.3 8.4 8.5 8.6 8.7 General . . . . . . . . . . . . . . . . . . . . . . . . 79 Gas bottles. . . . . . . .
Contents 12.1.2 12.1.3 12.1.4 12.1.5 12.1.6 12.2 12.3 12.4 12.5 12.5.1 12.5.2 12.5.3 12.6 12.6.1 12.6.2 12.6.3 13 Washing the caravan . . . . . . . . . . . . Windows of acrylic glass . . . . . . . . . . Hot galvanized chassis . . . . . . . . . . . Underbody. . . . . . . . . . . . . . . . . . . . . Waste water tank . . . . . . . . . . . . . . . Interior care . . . . . . . . . . . . . . . . . . . . Extractor hood. . . . . . . . . . . . . . . . . . Filter for the external water connection. . . . . . . . . .
Contents 6 Caravan - 11-06 - DET-0030-05 EN
Guarantee 1.1 Guarantee certificate 1 1Guarantee Vehicle data Model: Chassis manufacturer: Serial number: Initial registration: Purchased from company: Expiry of the guarantee period: Key number: Chassis number: Customer Address Surname, Christian name: Street, No.: Postal code, town: Dealer's stamp and signature We reserve the right to alter the construction, equipment and the scope of delivery. Special equipment is also listed that is not included in the standard scope of delivery.
1 Guarantee 1.2 Guarantee conditions 1. In addition to the legal guarantee and product warranty rights due to the customer, Dethleffs GmbH may also grant a guarantee of six years that the vehicles constructed by the company are sealed in such a manner that moisture cannot penetrate from the outside into the interior of the vehicle. The guarantee obligations do not apply if the leakage is a result of improper handling of the windows, doors and skylights or damage that has not been properly repaired.
Guarantee 1.3 1 Inspection records Delivery Signature and stamp of the Dethleffs dealer: 1st year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 1st year Water ingress test 1st year No defects found Found defects: Should it be determined during an inspection that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
1 Guarantee 2nd year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 2nd year Water ingress test 2nd year No defects found Found defects: 3rd year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
Guarantee 4th year 1 Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 4th year Water ingress test 4th year No defects found Found defects: 5th year Water ingress test Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
1 Guarantee 1.4 Inspection plan for annual inspection Pos. 12 Component Activity Interval 1 Skylights Remove the inside frame of the skylights and tighten the screw connections of the securing clips 1.
Guarantee Pos. Component Activity Interval 19 Brake cable assembly Visual check Every two years 20 Chassis underbody Check bolts are firmly secured Every two years 21 Gas system Official gas inspection Every two years 1 We reserve the right to modify the inspection plan. 1.5 Caravan - 11-06 - DET-0030-05 EN Inspection plan for water ingress test Pos. Component Activity 1.1 Wheel housing Visual check 1.2 Rear wall floor plateau connection Visual check 1.2.
1 Guarantee Pos. Component Activity 3.3 Front wall floor plateau connection Spray with Dethleffs special weatherproof solution 3.4 Side wall floor plateau right connection Spray with Dethleffs special weatherproof solution 3.5 Side wall floor plateau left connection Spray with Dethleffs special weatherproof solution We reserve the right to modify the inspection plan.
Introduction 2 Please read this instruction manual completely before using the vehicle for the first time! 2Introduction Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. The non-observance of this symbol can lead to personal injury. The non-observance of this symbol can lead to damage being caused to, or inside the vehicle. This symbol indicates recommendations or special aspects.
2 Introduction The reprinting, translation and copying, including extracts is not permitted without prior written authorisation from the manufacturer. 2.1 The vehicle comes without a wheelbrace and vehicle jack. We suggest you obtain a commercially available wheelbrace before you first use your caravan, in case of an emergency.
Introduction Caravan - 11-06 - DET-0030-05 EN 2 When parked, do not allow the engine of the towing vehicle to run more than necessary. When running idle, a cold engine releases more contaminants than usual. The running temperature of the engine is achieved more quickly whilst the vehicle is in motion. Use an environmentally-friendly WC chemical agent for the WC which can also be biologically degraded and only use small doses.
2 18 Introduction Caravan - 11-06 - DET-0030-05 EN
Safety 3 Chapter overview 3Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: 3.1 3.1.1 Fire prevention Avoidance of fire risks 3.1.2 EN Keep flammable materials clear of heating and cooking appliances. Lights can get very hot.
3 Safety 3.2 General 3.3 Observe the headroom of the conversion door. If a roof rack with ladder is installed, only climb the ladder if the rear corner steadies have been extended or the caravan is connected to the towing vehicle or the caravan has been secured against tilting at the back. Otherwise the caravan can tip over to the back. Danger of falling! As far as the appliances (heater, cooker, refrigerator, etc.) are concerned, the instruction manuals are authoritative.
Safety 3.4 EN Push in fully the drive-on ramp and lock it into place before commencing the journey. Check tyre pressure before a journey or every 2 weeks. Wrong tyre pressure causes excessive wear and can lead to damage or even to tyre burst. You can lose control of the vehicle. Before commencing the journey, distribute the payload evenly within the vehicle (see chapter 4).
3 Safety 3.5 3.5.1 Gas system General instructions 22 Close all gas isolator taps and the regulator tap before commencing the journey and when leaving the vehicle. No source of combustion using gas (gas cooker, gas heater, gas boiler, etc.) may be in operation when filling the fuel tank of the towing vehicle, on ferries or in the garage. Danger of explosion! Only have the gas system maintained, repaired or altered by an authorised specialist workshop.
Safety 3.5.2 EN Secure the gas bottle compartment against unauthorised access. To do this, lock the gas bottle compartment. The regulator tap on the gas bottle must be accessible. Only connect gas-operated devices (e.g. gas grill) which have been designed for a gas pressure of 30 mbar. The exhaust gas pipe must be fitted tightly to the heating system and to the vent and must be sealed. The exhaust gas pipe must not show any evidence of damage.
3 Safety 3.7 Water system 24 If the vehicle is not heated when there is risk of frost, empty the entire water system. Leave the water taps on in central position. Leave all drain cocks open. This will avoid frost damage to appliances and to the vehicle. Water left standing in the water tank or in the water pipes becomes undrinkable after a short period. For this reason, rinse the water pipes and the water tank thoroughly with several litres of fresh water before each use of the vehicle.
Before the journey Chapter overview 4 4Before the journey This chapter contains important information which has to be noted before commencing your journey or carrying out any tasks before the journey.
4 Before the journey Connecting: 4.4 Winterhoff or AL-KO stabiliser: The tow ball is not to be lubricated when using the stabiliser. The friction pads are pressed against the coupling ball and thereby generate an anti-rolling moment. This anti-rolling effect is only guaranteed when the towing vehicle coupling head is free of lubricant and other residues. When lubricating the stabiliser ensure that no lubricant is on the friction pads.
Before the journey 4.4.1 Albe caravan coupling Fig. 1 Connecting: 4.4.2 EM 150 R caravan coupling Pull the coupling handle (Fig. 1,1) upwards. The caravan coupling is open. Place the open caravan coupling on the towing vehicle towing ball and release the coupling handle. The caravan coupling now locks automatically and audibly in place. The handle glides automatically back to its initial position. In addition, push the coupling handle (Fig. 1,1) down with your hand (not with your foot).
4 Before the journey 4.4.3 AKS 3004 stabiliser Fig. 3 Connecting: 4.5 4.6 Pull the coupling handle (Fig. 3,2) upwards. Place the opened stabiliser on the caravan coupling. The coupling handle must audibly lock back into its initial position. In addition, push the coupling handle downwards by hand (not with your foot). Closing and securing is carried out automatically. Conduct a visual inspection: The green cylinder on the safety indicator (Fig. 3,3) must be visible.
Before the journey 4 Do not exceed the maximum permissible gross weight stated in the vehicle documents by the payload. Built-in accessories, special equipment and the gas bottles all reduce the payload. Adhere to the axle load stated in the vehicle documents. Load the caravan so that the drawbar coupling head is not pushed downwards due to the permissible nose weight. Heavy objects should be close to the axles and a weight centre should be in the centre of the vehicle.
4 Before the journey A full heating system A full toilet flushing system The power cables for the 240 V power supply The installation kit for an auxiliary battery if an auxiliary battery can be used The waste water and sewage tanks are empty.
Before the journey 4 For the personal equipment, according to the applicable regulations, the manufacturer must use a minimum weight that is determined according to the following formula: Formula Explanation Example Minimum weight M (kg) = 10 x N + 10 x L + 30 N = maximum number of beds, as stated by the manufacturer L = total length of the caravan in metres, not including the drawbar Caravan with 4 beds and a length of 5 m: Minimum weight M (kg) = 10 x 4 beds + 10 x 5 metres + 30 = 120 kg 4.6.
4 Before the journey For vehicles with tandem axles, distribute the weight centre over both axles. The payload arrangement recommended cannot be adhered to consequently as the storage facilities are to be found throughout the complete caravan. Ensure that heavy items are close to the axles and the lower area, i.e. directly above the vehicle floor. Store heavy objects (awning, tin cans, etc.), if possible, in the towing vehicle. Fig. 4 Incorrectly loaded Loads stored apart from each other (Fig.
Before the journey 1 2 3 Fig. 6 4 Caravan load Nose weight Axle load Caravan load, nose weight and axle load Caravan load The caravan load (Fig. 6,1) stipulated in the towing vehicle documents provides information as to the maximum weight which the towing vehicle is permitted to tow. The caravan load refers to the actual weight of the caravan and not to the maximum permissible gross weight of the caravan. Example The towing vehicle may tow 1,200 kg.
4 Before the journey 4.6.5 Roof load 4.6.6 Only climb the ladder if the rear corner steadies have been extended or if the caravan is connected to the towing vehicle or if the caravan has been secured against tilting to the back. Otherwise the caravan can tip over to the back. Danger of falling! Take care when stepping onto the ladder. There is danger of slipping when the ladder is moist or icy. Take care when stepping onto the roof.
Before the journey Loading the vehicle via the drive-on ramp 4 The vehicle is easier to load via the drive-on ramp. Fig. 7 Securing the drive-on ramp Fig. 8 Drive-on ramp (pulled out) Open the rear flap (see chapter 7). Remove the safety device (e.g. padlock, Fig. 7,1) from the drive-on ramp (Fig. 7,2). Hold the drive-on ramp in the horizontal position and pull it out to the rear as far as possible. Place the drive-on ramp on the ground (Fig. 8). Insert the edge guard (Fig.
4 Before the journey Fig. 9 Storing the television in the TV cabinet: Fig. 10 Alternative: Television (flat screen) Rotate the television to its initial position (Fig. 9) and lock it into place. Use handle (Fig. 9,1) to push the holder for the flat screen backwards. The latch (Fig. 9,2) will engage. 4.9 Television (flat screen) Close TV cabinet. Road safety Check tyre pressure before a journey or every 2 weeks.
Before the journey Housing body, inside Gas system Electrical system No.
4 38 Before the journey Caravan - 11-06 - DET-0030-05 EN
During the journey Chapter overview 5 5During the journey This chapter contains instructions on how to drive the caravan. The instructions address the following topics: 5.1 driving speed brakes driving in reverse Driving with the caravan During the journey, no persons are to travel inside the caravan. The caravan constructions were designed for a maximum permissible speed of 100 km/h (60 mph). Therefore never drive faster than 100 km/h (60 mph).
5 During the journey Fig. 11 Driving in reverse: 40 Fig. 12 Steer to the left Drive up to the entrance until the rear of the caravan is roughly level with the entrance (Fig. 11). Steer the stationary towing vehicle and trailer to the left (Fig. 12). Reverse with caution. The caravan moves to the right. Fig. 13 Approach Approach Fig. 14 Steer to the right The angle between the vehicles must not be too narrow, otherwise the corners will bump against each other.
Pitching the caravan Chapter overview 6 6Pitching the caravan This chapter contains instructions on how to pitch the caravan. The instructions address the following topics: 6.1 handbrake wheel chocks operation of the supports entrance step mobile waste water tank 240 V connection refrigerator Pitch the vehicle so that it is as horizontal as possible. Secure the vehicle to prevent it from rolling. Animals (especially mice) can cause great damage to the interior of the vehicle.
6 Pitching the caravan Fig. 16 Removal: 6.3 Wheel chock Swivel the retaining clip (Fig. 16,1) down. Remove the wheel chock (Fig. 16,2) from the holder. Corner steadies Do not use the fitted corner steadies as a vehicle jack. The corner steadies are only for stabilising the pitched caravan. The caravan wheels are not to be raised above the ground. When pitching the vehicle, ensure that the corner steadies are evenly loaded.
Pitching the caravan 6.4 Entrance step (free-standing) Make sure that the entrance step stands on secure and level ground. This will prevent the entrance step from toppling over. Do not step on the edges of the entrance step. Danger of slipping! Secure the entrance step to the ground, for example, with tent pegs. This way the entrance step cannot slip away. Fig. 18 6.5 6 Entrance step (free-standing) Place the entrance step (Fig. 18,1) in front of the entrance to the caravan.
6 44 Pitching the caravan Caravan - 11-06 - DET-0030-05 EN
Living Chapter overview 7 7Living This chapter contains instructions about living in the caravan. The instructions address the following topics: 7.1 Doors 7.1.1 opening and closing the doors and external flaps heating the vehicle ventilation of the vehicle opening and closing the windows and blinds opening and closing the skylights converting tables positioning the television lamps extending the seating groups use of the beds Only drive with locked doors.
7 Living 7.1.2 Conversion door, outside (hinged handle) Fig. 22 Opening: Locking: 7.1.3 Insert the key in the locking cylinder (Fig. 22,1) and turn it in a clockwise direction until the door lock is unlatched. Return the key to the central position and remove it. Pull on the handle (Fig. 22,2). The door is open. Insert the key in the locking cylinder (Fig. 22,1) and turn it in an anticlockwise direction until the door lock is engaged. Return the key to the central position and remove it.
Living Fig. 25 Opening the upper part of the door: 7.1.5 7 Catch lever on the lower part of the door Lock the lower part of the door. In order to carry this out turn catch lever (Fig. 25,1) a quarter turn in a clockwise direction. Open the upper part of the door. For conversion doors with a right-hand opening, locking and opening is done in the reverse directions to those of the conversion door shown. Insect screen on the split conversion door Fig.
7 Living Fig. 27 Closing: Opening: 7.2 Blind Pull blind downwards by the handle (Fig. 27,2) and lock it into place. Pull blind downwards gently by the handle (Fig. 27,2) and push the unlocking bar (Fig. 27,1) outwards. The lock (Fig. 27,4) is released from the holder (Fig. 27,3). Use handle to return the blind slowly to its initial position. External flaps Before commencing the journey, close all external flaps and lock them.
Living Fig. 28 Opening: Closing: 7.2.2 Insert key into locking cylinder (Fig. 28,1) and turn a quarter turn in an anticlockwise direction. The flap lock is unlatched. Remove the key. Pull on the lock handle (Fig. 28,2). The external flap is open. Firmly close the external flap. Insert key into locking cylinder and turn a quarter turn. The flap lock is locked. Remove the key. During rain, water can penetrate the opened flap lock. Therefore close the lock handle. Fig.
7 Living 7.2.3 Press down lock handle with key inserted and turn key a quarter turn in a clockwise direction. The lock handle will stay bolted. Remove the key. Flap lock, rectangular Fig. 30 Opening: Closing: 7.2.4 Insert key into locking cylinder (Fig. 30,1) and turn a quarter turn. The lock handle (Fig. 30,2) snaps out. Remove the key. Turn the lock handle one quarter turn. The flap lock is open. Firmly close the external flap. Turn lock handle until it is horizontal.
Living Closing: 7.2.5 Close the flap for the Thetford cassette and press it to shut it. Insert key into locking cylinder (Fig. 31,1) and turn a quarter turn. Remove the key. Cap for the fresh water filler neck Fig. 32 Opening: Closing: 7.3 EN The fresh water filler neck is labelled with the word "WASSER" (water) (Fig. 32,1). Insert the key in the locking cylinder (Fig. 32,2) and turn it in an anticlockwise direction. Remove cap. Place the cap on the fresh water filler neck.
7 Living Condensation 7.5 Windows The windows are fitted with a blind and an insect screen. After the latch has been released, the blind and insect screen automatically spring back to the initial position by tensile force. In order not to damage the tension mechanics, hold onto the blind or insect screen and allow it to slowly return to the initial position. Do not keep blinds closed over a longer period of time as that can cause increased material wear.
Living Fig. 33 Opening: Catch lever in "closed" position Fig. 34 7 Hinged window with rotary hinges, open Turn the catch lever (Fig. 33,3) a quarter turn towards the centre of the window. Open the hinged window until the required position has been reached and use knurled knob (Fig. 34,1) to secure in position. The hinged window remains locked in the required position. Closing: Turn knurled knob (Fig. 34,1) until the latch is released. Close the hinged window. Turn the catch lever (Fig.
7 Living 7.5.2 Hinged window with automatic hinges Open the window completely, to release the lock. If the locking device is not released and the window is closed nevertheless, there is the danger of the window breaking due to the massive counter-pressure. When opening the hinged windows, ensure that there are no torsional forces. Open and close the hinged windows evenly. If the catch lever is equipped with a safety knob, press the safety knob when operating the catch lever. Fig.
Living 7 Press the safety knob (Fig. 38,1) and keep it pressed. Turn the catch lever (Fig. 38,3) a quarter turn towards the centre of the window. Lightly open the hinged window outwards. Return the catch lever to its initial position. Move the locking catch (Fig. 38,3) on the catch lever into the recess of the window catch (Fig. 38,4). Release the safety knob (Fig. 38,1). Make certain that the safety knob is not pushed in but rather that it secures the catch lever.
7 Living Closing: Opening: 7.6 Pull insect screen at the handle (Fig. 39,1) down and hang it into the locking devices (Fig. 39,3) situated on both sides of the window frame. Press handle (Fig. 39,1) downwards and, at the same time, tilt it slightly inward. The insect screen can be taken out of the locking devices situated on both sides of the window frame. Use handle to return the insect screen slowly to its initial position.
Living 7.6.1 7 Skylight with snap latch (variant 1) Fig. 40 Forced ventilation Depending on the model, a skylight with forced ventilation (Fig. 40,1) is built in the toilet compartment. The skylight can be pushed upwards either from one side or from both sides. Fig. 41 Opening: Closing: Caravan - 11-06 - DET-0030-05 EN Insect screen Fig. 42 Skylight, handle Pull on the handle (Fig. 41,2). Fold insect screen (Fig. 41,1) downward. Push the spring-loaded latch (Fig.
7 Living Blind To close and open the blind: Fig. 43 Closing: Opening: 7.6.2 Blind Pull the blind (Fig. 43,1) using the handle (Fig. 43,2) and hook the hooks (Fig. 43,3) in the opening (Fig. 43,4). Pull the hooks (Fig. 43,3) out of the opening (Fig. 43,4) and guide the blind back. Skylight with snap latch (variant 2) The skylight can be pushed upwards either from one side or from both sides. Fig. 44 Opening: Closing: 7.6.
Living Fig. 45 Opening: Closing: Locking in the ventilation position: Roman shade Opening: Closing: Opening: Caravan - 11-06 - DET-0030-05 EN Fig. 46 Hinged skylight In order to do this, turn lever (Fig. 45,1 or Fig. 46,3) a quarter turn in an anticlockwise direction. Grip lever and push hinged skylight upwards. Grip lever and pull hinged skylight downwards. Turn the lever one quarter turn. The latch (Fig. 45,4) must slide into the lower aperture (Fig. 45,3).
7 Living 7.6.4 Heki skylight Fig. 47 Heki skylight, closed Fig. 48 Heki skylight in ventilation position 1 The Heki skylight may be opened on one side only. Opening: Closing: Ventilation position (variant 1): Press the safety knob (Fig. 47,1) and turn the catch lever (Fig. 47,2) one quarter turn inward. Pull the bar (Fig. 47,4) downwards out of the latch. Press the Heki skylight upwards using the bar. Press the bar back into the latch. Pull the bar (Fig.
Living Fig. 50 Roman shade Opening: Pull out Roman shade at the handle (Fig. 50,2) and release in the required position. The Roman shade will stay in that position. Slowly push Roman shade at the handle to its initial position. To close and open the insect screen: Closing: Opening: 7.6.5 Heki skylight, blind lock To close and open the Roman shade: Closing: Insect screen 7 Pull insect screen at the handle (Fig. 50,1) to the opposite handle of the Roman shade (Fig.
7 Living Closing: Opening: Insect screen Opening: 7.7.1 Slowly push Roman shade at the handle to its initial position. If the insect screen is locked with the Roman shade, the Roman shade is also moved along on closing the insect screen. Closing: 7.7 Pull the handle of the Roman shade (Fig. 51,3) and release in the desired position. The Roman shade will stay in that position. Pull insect screen at the handle (Fig. 51,1) to the opposite handle of the Roman shade (Fig.
Living Fig. 53 Fastening to the floor: Lock for swivel table with clamp Fig. 54 7 Lock for swivel table without clamp Place the swivel table next to the holder (Fig. 53,3) or on the holder (Fig. 54,2). Place the bar (Fig. 53,2) with the securing bolt (Fig. 53,1) over the table leg. Move the bar and possibly also the swivel table in such a way that the securing bolt (Fig. 53,1 or Fig. 54,1) can be screwed into the holder (Fig. 53,3 or Fig. 54,2).
7 Living Fig. 57 Putting up: Removal: Take the folding table out of the holder in the wardrobe. Place the folding table with the legs upwards onto the seat cushions. Fold the legs (Fig. 57,4) one after the other outwards, until the support clips (Fig. 57,2) engage in the hooks (Fig. 57,1) of the guides. Carefully turn round the folding table and place it between the benches. Carefully turn the folding table round and place it with the legs upwards onto the seat cushions.
Living Fig. 59 7 Lift-off table for the round seating group The lift-off table's lifting mechanism permits it to be used as a bed foundation. Conversion to bed foundation: 7.8 Swivel the catch lever (Fig. 59,3) to the left. The lock is open. Press the table-top (Fig. 59,2) in the middle downwards to the desired stop limit (Fig. 59,1 or 4) and hold it down. Swivel the catch lever (Fig. 59,3) to the right. The lift-off table is locked.
7 Living Fig. 61 Positioning the flat screen with jointed arm: 7.9 Pull on the fabric strip (Fig. 61,3) to unlock the jointed arm (Fig. 61,2). Swivel the flat screen (Fig. 61,1) into the desired position. Take hold of the flat screen at the top and bottom edge with both hands and set the desired angle of inclination. Lamps Bulbs and light fittings can be extremely hot. Allow the light bulbs and lamp holders to cool down before touching them.
Living 7.10 Extending the central seating group Fig. 63 Extending: Retracting: 7.11 7.11.1 7 Support for bench seat extension Fold up the bench seat extension (Fig. 63,1). The support (Fig. 63,2) locks automatically into place. Lay the additional cushion onto the bench seat extension. Take the additional cushion from the bench seat extension and store it. Press the support (Fig. 63,2) against the resistance of the coil spring (Fig. 63,3) upwards in the direction of the arrow.
7 Living Fig. 64 Bunk bed, folding When the bunk bed is folded up, secure it with the retaining belt (Fig. 64,1). Depending on the model, the vehicle is fitted with a folding bunk bed. When the bunk bed is folded down, it can be used immediately without any additional conversion. The bunk beds can be folded up. The space under the bed can be used for storage. 7.11.3 Fixed bed Do not let the slatted frame fall down when closing the bed! Fig.
Living Only lower or raise the bed when the space between the bed and the side wall is clear. Only lower the bed if the lowering area in the rear garage is clear. The bed can be adjusted to any height between both end positions. The rocker switch for lifting and lowering the rear bed is located in the top section of the intermediate wall on the right side. Fig. 66 Raising: Lowering: 7.11.5 EN Operating switch for the electronically adjustable rear bed Fig.
7 Living Take care when swivelling the folding bed. Curtains or net curtains could be trapped and damaged. Fig. 68 Unfold: 70 Fig. 69 Swivel the folding bed Remove the table from the upper retainer and lay it aside. Remove the cushions from the seating group and lay them aside. Grip the folded sleeping area (Fig. 68,1) of the folding bed in the middle with one hand and tilt it slightly forwards.
Living Fig. 72 Folding together: Caravan - 11-06 - DET-0030-05 EN 7 Folding bed, folding together Release the retaining straps of the safety net from the holders on the ceiling. Unhook the access ladder from the flush of the folding bed and store it. Remove the cushions from the lower bed and the table and lay them aside. Remove the mattress from the sleeping area and store it. Lay the safety net onto the sleeping area. Fold the back part of the split sleeping area forwards (Fig.
7 Living 7.12 7.12.1 Converting seating groups for sleeping Bench seating group and side seating group Depending on the model, the seating group can be different in shape and position to the one shown here. 1 2 3 4 5 Fig. 73 Prior to conversion Fig. 74 After conversion 72 Back cushion Seat cushion Table Bar Mounting rail Convert the table (Fig. 73,3) to a bed foundation (see section 7.7). Insert the bar (Fig. 73,4) or pull it to the centre.
Living 7.12.2 Round seating group with rectangular table Depending on the model, the seating group can be different in shape and position to the one shown here. 1 2 3 4 5 Fig. 75 Prior to conversion Fig. 76 During conversion Fig. 77 After conversion Caravan - 11-06 - DET-0030-05 EN 7 Back cushion Seat cushion Table Back cushion Back cushion Convert the table (Fig. 75,3) to a bed foundation (see section 7.7). Pull the seat cushions (Fig. 76,2) into the centre.
7 Living 7.12.3 Round seating group with round table 1 2 3 4 5 6 Fig. 78 Prior to conversion Fig. 79 During conversion Fig. 80 After conversion 74 Back cushion Seat cushion Table Back cushion Back cushion Additional cushion Convert the table (Fig. 78,3) to a bed foundation (see section 7.7). Remove the back cushions (Fig. 79,1, 4 and 5). Insert the additional cushion (Fig. 80,6) between the seat cushions (Fig. 80,2) on the table (Fig. 79,3).
Living 7.12.4 Widening the bed into a playing area (variant 1) 1 2 3 4 5 6 7 8 9 Fig. 81 Prior to conversion Fig. 82 During conversion Fig. 83 After conversion Caravan - 11-06 - DET-0030-05 EN 7 Back cushion Seat cushion Table Back cushion Back cushion Bedding box extension Additional board Additional cushion Bed Convert the table (Fig. 81,3) to a bed foundation (see section 7.7). Turn table one quarter turn in a clockwise direction and pull forwards to the right.
7 Living 7.12.5 Widening the bed into a playing area (variant 2) Fig. 84 Prior to conversion Fig. 85 During conversion Fig. 86 After conversion 76 1 2 3 4 5 6 7 8 9 10 Back cushion Seat cushion Table Table leg Retainer Retainer Additional board Support legs Bed Additional cushion Swivel the table (Fig. 84,3) 45° upwards and remove it from the upper retainer (Fig. 84,5). Remove table leg (Fig. 84,4). Insert the bar (Fig. 84,6) or pull it to the centre.
Living 7.12.6 Seating group with two single beds 1 2 3 4 5 Fig. 87 Prior to conversion Fig. 88 During conversion Fig. 89 After conversion Caravan - 11-06 - DET-0030-05 EN 7 Back cushion Seat cushion Folding table Bedside locker Slatted frame Fold up the folding table (Fig. 87,3) and store in the provided holder (see section 7.7.3). Completely pull out the slatted frame (Fig. 87,5). Place the back cushions (Fig. 88,1) on the slatted frames.
7 78 Living Caravan - 11-06 - DET-0030-05 EN
Gas system Chapter overview 8 8Gas system This chapter contains instructions regarding the gas system of the caravan. The instructions address the following topics: safety gas consumption changing the gas bottles gas isolator taps external gas connection automatic switching facility The operation of the gas operation appliances of the vehicle is described in chapter 10. 8.
8 Gas system 8.2 Regularly inspect the gas tube fitted to the gas bottle connection for tightness. The gas tube must not have any tears and must not be porous. Have the gas tube replaced by an authorised specialist workshop no later than ten years after the manufacturing date. The operator of the gas system must see to it that the parts are replaced. Due to its function and construction, the gas bottle compartment is a space which is open to the exterior.
Gas system 8.3 Connect gas pressure regulator complete with safety valve directly to bottle valve. The gas pressure regulator reduces the gas pressure in the gas bottle down to the operating pressure of the gas devices. If 2 gas bottles are used at the same time: Connect a gas pressure regulator fitted with an automatic switchover device. Information available at the Dethleffs service centre.
8 Gas system 8.5 Unscrew the gas pressure regulator (Fig. 90,3) along with the gas tube (Fig. 90,5) from the gas bottle with a suitable gas spanner. Release the fixing belts (Fig. 90,2) and take out the gas bottle. Place a filled gas bottle in the gas bottle compartment. Fix gas bottle in place with the fixing belts. Screw the gas pressure regulator with gas tube on the gas bottle and secure with a suitable gas spanner (Do not overtighten). Gas isolator taps 1 2 3 4 Fig.
Gas system Fig. 92 8 External gas connection, gas isolator tap closed The external gas connection (Fig. 92) is located at the front right. 8.7 Connect the external gas device to the connection point (Fig. 92,1). Open the gas isolator tap (Fig. 92,2). Duomatic switching facility Do not use the switching facility in closed spaces. Also read the manufacturer's instruction manual. The Duomatic is an automatic switching facility with a remote display for a twobottle gas system.
8 Gas system The manometer (Fig. 93,2) on the central regulator indicates the pressure in the gas bottle, not the filling level of the gas bottle. The manometer can be used to test the impermeability of the gas bottle. Only the electrical functions can be switched at the operating unit (Fig. 94). The regulator taps on the gas bottles (Fig. 93,1 and 4) must be opened manually. The central regulator provides a constant gas pressure, regardless of which gas bottle is being drawn upon.
Gas system Changing gas bottles: Caravan - 11-06 - DET-0030-05 EN 8 Always mount the regulator in such a way that the protective cap faces upwards. Close the regulator tap on the empty gas bottle. Unscrew the regulator of the gas bottle. Connect the full gas bottle to the regulator. Open the regulator tap on the gas bottle. Set the knob on the switching regulator with a half-turn, so that the newly replaced gas bottle will serve as a reserve bottle.
8 86 Gas system Caravan - 11-06 - DET-0030-05 EN
Electrical system Chapter overview 9 9Electrical system This chapter contains instructions regarding the electrical system of the caravan.
9 Electrical system 9.3 12 V power supply If you use the battery of the towing vehicle to provide power for the caravan, bear in mind that the battery capacity is restricted. If you place too great a burden on the battery, this may lead to starting difficulties. Always disconnect the electrical connection between the towing vehicle and the caravan before the caravan is connected to a 240 V power supply. In order to carry this out, disconnect the plug from towing vehicle socket.
Electrical system 9 The dryfill battery is maintenance-free. Maintenance-free means: It is not necessary to check the acid level. It is not necessary to lubricate the battery poles. It is not necessary to refill the distilled water. Even a maintenance-free dryfill battery must be charged regularly. When the vehicle is not connected to the 240 V power supply or the 240 V power supply is switched off, the living area battery supplies the living area with 12 V DC.
9 Electrical system Energy reserves 9.3.3 Off-load voltage (measured at the poles) Charging condition Higher than 12.80 V 100 % Approx. 12.55 V 75 % Approx. 12.32 V 50 % Approx. 12.18 V 25 % Lower than 12.00 V 0% The living area battery has a limited power supply only. That is why electrical appliances should not be operated over a long period of time if the vehicle is not connected to the 240 V power supply or the engine of the towing vehicle is switched off.
Electrical system 9 connected by a relay. This prevents the battery of the towing vehicle from being run down by electrical appliances in the living area. The starting capability of the towing vehicle is thus preserved. Charging with an external charger When charging the living area battery with an external charger, proceed as follows: 9.4 Disconnect the caravan electrically from the towing vehicle. Switch off 12 V main switch on the panel. The indicator lamp will go off.
9 Electrical system Variant 1 Fig. 95 Power pack (variant 1) The 240 V automatic circuit breaker (Fig. 95,1), the overload protection (Fig. 95,2) and the main fuse (Fig. 95,3) are integrated in the power pack. The overload protection switches all 12 V appliances in the caravan off, if the power pack overheats. The power pack can overheat, if the ventilation apertures are covered by clothing or if many 12 V appliances are operated for a long time.
Electrical system Switching on overload protection: 9.5 When the overload protection triggers, allow the power pack to cool. Press upper part of the main switch (Fig. 96,4) first: Position "OFF". After about 60 seconds, switch the main switch back to position "ON". Transformer/rectifier EBL 109 (Power Pack SE) Do not cover the ventilation slots. Danger of overheating! Fig.
9 Electrical system When the transformer/rectifier is subject to a heavy load, the fitted charger module reduces the charging current. This protects the charger from overheating. The transformer/rectifier is subject to a heavy load when e.g. an empty living area battery is being charged, additional electrical appliances are turned on and the ambient temperatures are high. Position Depending on the model, the transformer/rectifier is situated either in the bench or in the bedding box. 9.5.
Electrical system 9.6.1 9 12 V main switch The 12 V main switch (Fig. 98,1) switches the 12 V power supply of the living area on and off. Switching on: Switching off: 9.6.2 Push the rocker switch (Fig. 98,1) up: The 12 V living area power supply is switched on. The 12 V indicator lamp (Fig. 98,2) lights up in green. Push the rocker switch (Fig. 98,1) down: The 12 V living area power supply is switched off. The 12 V indicator lamp (Fig. 98,2) goes off.
9 Electrical system 9.7 240 V power supply Only allow qualified personnel to work on the electrical system. The 240 V power supply provides electricity for: sockets with earth contact for appliances with maximum 16 A refrigerator 12 V living area power supply The electrical appliances which have been connected to the 12 V power supply system of the living area are supplied with power from the living area battery (Power Pack SE) or the power pack.
Electrical system Fig. 99 9.8 Fig. 100 Connecting an angled connector with socket Adapter cable: CEE 17 socket with earth contact (Fig. 99,1) – plug with earth contact (Fig. 99,2) Cable reel: Socket with earth contact (Fig. 99,3) – plug with earth contact (Fig. 99,4) Adapter cable: CEE 17 socket with earth contact (Fig. 99,5) – plug with earth contact (Fig. 99,6) When using a CEE 17 angled connector with rear socket (Fig.
9 Electrical system Before changing fuses, take the function, value and colour of the relevant fuses from the following specifications. When changing fuses, only use flat fuses with the values shown below.
Electrical system Thetford toilet fuse (fixed seat) 9 The fuse is located in the locker wall of the Thetford cassette. 1 Flat fuse 3 A/purple Fig. 103 Fuse for the Thetford toilet Changing: 9.8.2 Open the flap for the Thetford cassette on the outside of the vehicle. Remove the Thetford cassette and swing out the flap in the housing panel. Replace fuse (Fig. 103,1). Fuses 240 V Fig. 104 Safety cut-out (variant 1) Fig. 105 Safety cut-out (variant 2) A two-pole safety cut-out (Fig.
9 Electrical system Fig. 106 View of the Caravan plug Contact number DINspecification 1 L 2 Connection diagram 12N - black Connection diagram 12S - grey 9.9.2 Cable colour Cross section of the wire Left direction indicator Yellow 1.5 mm2 54 G Fog tail light Blue 1.5 mm2 3 31 Earth return White 2.5 mm2 4 R Right direction indicator Green 1.5 mm2 5 58 R Right tail light, side marker light (white/red), clearance light, marker light (amber), licence plate light Brown 1.
Appliances 10 Chapter overview 10Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction manuals for the appliances, included separately with the vehicle. The instructions address the following topics: 10.
10 Appliances 10.2 Heater In winter, check that the waste gas vent on the vehicle roof is free of snow and ice before using the heater. Never let gas escape unburned due to danger of explosion. When filling the fuel tank of the towing vehicle, on ferries or in the garage, never run the heater in gas operation. Danger of explosion! From heat setting 3 to 4 on switch on circulation fan. There is danger of overheating for the heater! Do not damage the exhaust gas pipe.
Appliances 10 Fig. 109 Hot-air heater control knob Switching on without automatic ignition: Switching on with automatic ignition: Switching off: Caravan - 11-06 - DET-0030-05 EN Open the regulator tap on the gas bottle and the gas isolator tap "Heater". Turn control knob on the heater to the required position and press it firmly. Press gas ignition button (at the control knob) several times in succession. Keep the control knob pressed until the flame burns.
10 Appliances Fig. 110 Removing heater cover Changing the battery on the automatic ignition: Fig. 111 Heater opened Make certain that the heater is switched off. Remove heater cover (Fig. 110,2). Pull the heater cover upwards and forwards, press up the retaining springs (Fig. 110,1) to the side and tip the cover forwards. Turn the cover (Fig. 111,1) to the side, so that the connecting cables for the hot-air fan as well as the ignition control lamp do not need to be disconnected.
Appliances 10 Fig. 113 Operating switch for circulation fan (240 V) Switching circulation fan (240 V) on: Switching circulation fan (240 V) off: Turn the rotary switch (Fig. 113,1) to " ". Turn the knob (Fig. 113,2) to the required position of the circulation fan. Turn the rotary switch (Fig. 113,1) to " ". Fig. 114 Operating switch for circulation fan (12 V) A circulation fan for 12 V line voltage is available as special equipment.
10 Appliances Fig. 115 Circulation fan Fig. 116 Circulation fan, adjustment flap in central position The hot air flow can be adjusted as required with the operating lever (Fig. 115,1) on the back of the circulation fan. Factory setting is the central position. In the central position the warm air is distributed evenly to each warm air outlet. The operating lever (Fig. 116,1) for the adjustment flap is located under the base flap in the wardrobe. Setting the hot air distribution: 10.2.
Appliances 1 2 3 4 5 6 7 8 9 10 10 LCD display "Back" button "Activate/Increase" button "Forward" button "Switch off/Decrease" button "System reset" button Lower menu line Information line Status line Upper menu line Fig. 117 Operating unit for hot-water heater Control buttons When no button is pressed, the operating unit automatically switches to home position after two minutes. The control buttons have the following functions: No. in Fig.
10 Appliances Fig. 118 LCD displays No. in Fig. 118 Upper menu line Status line On The heater is activated 2 Off The heater is switched off 3 Selection: Setting the desired temperature 4 Selection: Temporarily increasing (approx.
Appliances No. in Fig.
10 Appliances Switching on the heater: Switching the heater off: Setting the rotational speed of the circulating pump Press the " " button (Fig. 117,4). The "Off" symbol (Fig. 118,2) flashes. Press the "+/On" button (Fig. 117,3). The "On" symbol (Fig. 118,1) flashes. The heater starts automatically. Press the " " button (Fig. 117,2). The operation ends, the display moves to home position and the "On" symbol lights up. Press the " " button (Fig. 117,4). The "On" symbol (Fig.
Appliances 10.2.5 10 Select the "AU" (240 V) or "12" (12 Volt) setting with the "+/On" button (Fig. 117,3) or the "-/Off" button (Fig. 117,5). Exit the menu command with the "Store" button (Fig. 117,6). Ultraheat additional electric heater The Ultraheat additional electric heater is built-in to the hot-air heater.
10 Appliances When the warming unit is turned on, the temperature of the waste water pipes is monitored by temperature sensors. If the temperature falls below 5 °C, the heating elements are switched on and the waste water pipes are warmed. If the temperature rises above a certain level, the heating elements are switched off again. Fig. 121 Transformer with control unit The 240 V AC/12 V DC transformer (Fig. 121,2) is installed in the wardrobe. The control unit is integrated in the transformer housing.
Appliances Operating levels 10 The electrical floor warming unit has four operating levels: 0 "Off" 20 V "Low heating level" 22 V "Medium heating level" 24 V "High heating level" Fig. 122 Regulator for electrical floor warming unit Switching on: Switching off: Connect the vehicle to the 240 V power supply (see section 9.7.1). Turn the control knob (Fig. 122,2) to the required heating level. Turn control knob (Fig. 122,2) to "0" position.
10 Appliances Fig. 123 Regulator for floor warming unit/warming unit for waste water tank Switching on: Switching off: 10.3 Set regulator (Fig. 123,1) to the desired flow level (max flow = arrows (Fig. 123,2) in direction of lines). Turn the regulator (Fig. 123,1) until both arrows (Fig. 123,2) are at a right angle to the heating lines. Switch off the hot-water heater if necessary (see section 10.2.4).
Appliances Manual mode Switching on the ventilation: Switching on the cooling: The ventilation, cooling and heater can be set separately in manual mode. Switching on the heater: Switching off: 10.4 EN Use the " " (Fig. 124,1), "+" (Fig. 124,2) and "–" (Fig. 124,5) buttons to set the desired cooling fan speed. Set the mains switch (Fig. 124,4) to "I". Press the "MODE & SET" button (Fig. 124,6) until the cooling symbol appears in the display (Fig. 124,3).
10 Appliances 10.4.2 Truma boiler Remove cap from waste gas vent before using the Truma boiler. The boiler is gas operated. The electrical control of the boiler is provided with power by the living area battery. 1 2 3 4 5 Temperature control knob Red indicator lamp "Fault" Rotary switch Off On Fig. 125 Operating unit for Truma boiler Switching on: Remove cap from waste gas vent. Open the regulator tap on the gas bottle and the gas isolator tap "Boiler". Switch the 12 V power supply on.
Appliances Emptying the boiler: 10.4.3 Switching the boiler on/ off Filling/emptying the boiler 10 Set all the water taps to "Hot" and open them. The water pump is turned on. The warm water pipes are filled with water. Keep the taps open until the water flowing out of the taps has no bubbles in it. This is the only way to ensure that the boiler is full of water. Close all water taps. Turn the rotary switch (Fig. 125,3) to " ". Turn knob (Fig.
10 Appliances 10.4.4 Open drain cocks (Fig. 127). To do this, set the rocking levers (Fig. 127,1) in a vertical position. The boiler is drained to the outside using the drain cocks. Check whether the water has been drained completely from the boiler (approx. 12.5 litres). Further information can be obtained from the separate instruction manual "Alde Compact". Reich boiler Fig. 128 Reich boiler The boiler is operated with 240 V. The boiler heats about 5 l of water.
Appliances 10.4.5 10 Further information can be obtained in the manufacturer's instruction manual. Hot water source Never use the hot water source without water inside it. If the hot water source is not being used, empty it if there is any risk of frost. Switch off the hot water source and empty it if the vehicle is not used. If you want to empty the hot water source: Empty the water tank completely before opening the drain cocks of the hot water source.
10 Appliances Fig. 130 Drain cocks for hot water source Filling the hot water source with water: Emptying the hot water source: 10.5 Switch off the operating switch (Fig. 129). Indicator lamp (Fig. 129,1) in the switch is not on. Close drain cocks. To do this, close the caps (Fig. 130,1 and 2) by turning them in a clockwise direction. Set all the water taps to "Hot" and open them. The water pump is turned on. The warm water pipes are filled with water.
Appliances 10.5.1 10 Gas cooker During activation and operation of the gas cooker, no flammable objects or highly inflammable objects such as dishcloths, napkins etc. must be near the gas cooker. Fire hazard! The process of ignition must be visible from above and must not be covered by cooking pans placed on the cooker. Depending on the model, the gas cooker lid is held closed by a spring. When closing there is danger of getting injured! Do not use the glass gas cooker lid as a hob.
10 Appliances Switching off: 10.5.2 Turn the control knob to the 0-position. The flame fades. Close the gas isolator tap "Cooker" and the regulator tap on the gas bottle. Gas oven Keep the ventilation openings on the gas oven open at all times. There must be no flammable objects near the gas oven when it is being lit. The oven flap must remain open when it is being lit. If ignition has not taken place, repeat the entire procedure.
Appliances 10.5.3 Gas cooker 10 Gas cooker with gas oven and gas grill During activation and operation of the gas cooker, no flammable objects or highly inflammable objects such as dishcloths, napkins etc. must be near the gas cooker. Fire hazard! The process of ignition must be visible from above and must not be covered by cooking pans placed on the cooker. The gas cooker lid is held closed by a spring.
10 Appliances Gas oven and gas grill Switching on the gas grill: Switching on the gas oven: Switching off the gas oven and gas grill: 10.5.4 There must be no flammable objects near the gas oven or the gas grill when it is being lit. The flap must remain open when it is being lit. If ignition has not taken place, repeat the entire procedure. If necessary, check if there is gas and/or current in the gas oven or the gas grill.
Appliances 10 Never leave the microwave oven unattended when it is in operation. If there is smoke, keep the microwave oven closed, switch it off and interrupt the power supply. Operate the microwave oven only with the rotary plate and the rotary cross in place. Use only crockery suitable for microwave use. The microwave oven only functions with correct 240 V power supply. In the case of fluctuations of the voltage or of voltage below 230 V, the microwave oven switches itself off completely.
10 Appliances Fig. 136 Extractor hood with lights Fig. 137 Extractor hood without lights Press switch (Fig. 136,2 or Fig. 137,1) to switch the extractor hood on and off. The switches (Fig. 136,1 and 3) are used to turn the cooker lamp in the extractor hood on and off. Depending on the model, the cooker lamp can be operated with 240 V with switch (Fig. 136,1). The cooker lamp is operated with 12 V with switch (Fig. 136,3). 10.
Appliances 10 Thetford Fig. 139 Refrigerator ventilation grill (Thetford) Removal: 10.6.2 Operating modes Move the locking device (Fig. 139,1) to the middle. Remove refrigerator ventilation grill. Operation (Dometic 4 series) The refrigerator has 2 operating modes: Gas operation Electrical operation (240 V AC or 12 V DC) The operating mode is set with the operating controls on the refrigerator panel.
10 Appliances 1 2 3 4 5 Energy selector switch 12 V Energy selector switch 240 V Temperature setting control knob, 240 V operation Temperature setting control knob, gas operation Gas ignition button Fig. 141 Operating controls for refrigerator Switching on: Switching off: Electrical operation Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". Set the 12 V switch " Set 240 V switch " " (Fig. 140,1 or Fig. 141,1) to " ". " (Fig.
Appliances Switching the 240 V operation off: Switching the 12 V operation on: Switching the 12 V operation off: 10 Turn the control knob to the 0 position and switch off the 240 V switch. Refrigerator is switched off. Set 240 V switch " Set 12 V switch " " (Fig. 140,2 or Fig. 141,2) to " ". " (Fig. 140,1 or Fig. 141,1) to "I". Switch off the 12 V switch. Refrigerator is switched off.
10 Appliances 1 2 3 Energy selector switch Control knob for setting the temperature Gas ignition button Fig. 142 Operating controls for the refrigerator (Dometic 7 series) Switching on: Switching off: Electrical operation Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". Set the energy selector switch (Fig. 142,1) to "GAS". Press the control knob (Fig. 142,2), turn it to the highest level and hold it down. Wait until gas gets into the burner.
Appliances 10 When operated with 12 V, the refrigerator is power-supplied by the starter battery of the towing vehicle (via the thirteen-pin connector). Therefore 12 V operation of the refrigerator is only possible while the engine of the towing vehicle is running. During prolonged driving breaks, change over to gas operation. The thermostat is not activated during 12 V operation. The refrigerator operates continuously. 10.6.
10 Appliances Switching off: Electrical operation Keep the control knob (Fig. 143,3) pressed down until the flame indicator (Fig. 143,2) becomes green and then release it. If the flame fades, then the ignition device will repeat the ignition process. Adjust the refrigerating temperature with the control knob. Set the energy selector switch (Fig. 143,1) to " ". Refrigerator is switched off. Close the gas isolator tap "Refrigerator" and the regulator tap on the gas bottle.
Appliances Gas operation 10 Never let gas escape unburned due to danger of explosion. It is not permitted to operate the refrigerator with car gas. Before starting up the refrigerator with gas, remove the two louvered panel covers (SE) for the refrigerator on the outside of the vehicle. 1 2 3 4 5 6 Frame heater (FH) button Indicator lamp, frame heater Energy selector switch Control knob for setting the temperature Gas ignition button Flame indicator Fig.
10 Appliances Switching the 240 V operation on: Switching the 240 V operation off: Switching the 12 V operation on: Switching the 12 V operation off: Frame heater (FH) Set energy selector switch (Fig. 144,3) to "240 V". Use the control knob (Fig. 144,4) to adjust the refrigerating temperature. Set energy selector switch to " ". Refrigerator is switched off. Set energy selector switch (Fig. 144,3) to "12 V". Use the control knob (Fig. 144,4) to adjust the refrigerating temperature.
Appliances 10 Dometic 4 series with push button Fig. 145 Locking of the refrigerator door (Dometic 4 series with snap fastener) Opening: Closing: Locking in the ventilation position: Push the green retainer lock (Fig. 145,4) to the side to release the locking device. The bolt (Fig. 145,3) will trip. Open the refrigerator door by the recessed grip or by the curved handle. Fully close the refrigerator door. Press the bolt (Fig.
10 Appliances Locking in the ventilation position: Slightly open refrigerator door. Turn lock (Fig. 146,2) towards the centre of the refrigerator. Move the outer recess (Fig. 146,3) of the lock over the locking catch (Fig. 146,4). The refrigerator door will then stay slightly open. Dometic 7 series Fig. 147 Locking of the refrigerator door (Dometic 7 series) Opening: Closing: Locking in the ventilation position: Push the lock (Fig. 147,1) to the left " Fig.
10 Appliances Closing: Locking in the ventilation position: Fully close the refrigerator door/freezer compartment door. Push the lock (Fig. 149,1) to the side, so that the closed lock " (Fig. 149,2) is completely visible. " Slightly open refrigerator door/freezer compartment door. Push the lock completely to the right. The door latch (Fig. 150,1) keeps the refrigerator door/freezer compartment door in a fixed position.
10 138 Appliances Caravan - 11-06 - DET-0030-05 EN
Sanitary fittings Chapter overview 11 11Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the caravan. The instructions address the following topics: 11.1 the external water connection waste water tank complete water system toilet compartment toilet Water supply, general Fill the water tank with fresh water only. If the vehicle is not heated when there is risk of frost, empty the entire water system. Leave the water taps on in central position.
11 Sanitary fittings 11.3 Insert the plug for the power supply on the supply point. Waste water tank 11.3.1 Insert the hose of a water pump with the coupling on the connection coupling. Before commencing the journey, empty the waste water tank. If there is any risk of frost, empty the waste water tank.
Sanitary fittings 11.3.2 11 Waste water tank, permanently installed Fig. 155 Waste water drain neck and drain cock The waste water tank is located in the caravan and is permanently mounted. The waste water tank collects waste water. Emptying: 11.3.3 Place a suitable container under the waste water drain neck (Fig. 155,2) or position the vehicle with the drain neck over a specially designated disposal point. Open the drain cock (Fig. 155,1). The waste water will run out. Close drain cock.
11 Sanitary fittings 11.3.4 Odour seal Fig. 157 Odour seal In order to prevent odours occurring in the waste water system, the vehicle depending on the model - has been equipped with odour seals (Fig. 157,1). The odour seals are installed in the waste water pipes. Clean the odour seals every two years at the latest. To do so, unscrew and remove the bottom cover (Fig. 157,2). 11.4 Filling the water system 11.5 Position the vehicle horizontally.
Sanitary fittings 11 Take note of the environmental tip in this chapter. To empty and ventilate the water system, proceed as follows. This will avoid frost damage: 11.6 Position the vehicle horizontally. Switch off the 12 V power supply on the panel (Power Pack SE). Switch off the 240 V power supply on the 240 V automatic circuit breaker. Open all drain cocks. Take off the external water connection. Open all water taps and set to the central position.
11 Sanitary fittings 11.7 After using the shower, wipe it dry to prevent moisture from collecting. Toilet 11.7.1 After taking a shower, rinse soap residue from the shower tray, otherwise cracks can appear in the shower tray over time. If there is any risk of frost and the vehicle is not heated, empty the Thetford cassette. Do not sit on the lid of the toilet. The lid is not designed to bear the weight of a person and could break. Use a suitable chemical for this toilet.
Sanitary fittings 11.7.2 11 Toilet with fixed seat Fig. 161 Thetford toilet with fixed seat Flushing: Emptying: 11.7.3 Press flush button (Fig. 161,1) and at the same time rotate in an anticlockwise direction. After flushing, turn flush button in a clockwise direction, the sliding trap is closed. Turn the flush button (Fig. 161,1) in a clockwise direction. The sliding trap is closed. To empty, the sliding trap in the Thetford toilet must be closed.
11 Sanitary fittings Swivel the fresh water filler neck inwards. Close the flap for the Thetford cassette. Fig. 164 Operating unit Thetford toilet Flushing: Before flushing open the sliding trap of the Thetford toilet. To do this, turn the slide lever (Fig. 164,1) in an anticlockwise direction. For flushing, press the blue flush button (Fig. 164,3). After flushing close the sliding trap. To do this turn the slide lever (Fig. 164,1) in a clockwise direction. The indicator lamp (Fig.
Sanitary fittings Fig. 165 Flap for the Thetford cassette 11.7.5 11 Fig. 166 Thetford cassette Open the flap for the Thetford cassette on the outside of the vehicle. Insert the key into the locking cylinder of the push-button lock (Fig. 165,1) and turn a quarter turn in a clockwise direction. Remove the key. Press both push-button locks (Fig. 165,2) simultaneously with your thumb and open the flap for the Thetford cassette. Pull the retaining clip (Fig.
11 148 Sanitary fittings Caravan - 11-06 - DET-0030-05 EN
Care 12 Chapter overview 12Care This chapter contains instructions regarding the care of the vehicle. The instructions address the following topics: exterior of the vehicle interior extractor hood winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time. The checklist address the following topics: 12.1 12.1.
12 Care 12.1.3 Treat rubber seals of doors and storage flaps with talc. Treat locking cylinder of doors and storage flaps with graphite dust. Windows of acrylic glass Acrylic glass windows are delicate and require very careful handling. 12.1.4 Never rub acrylic glass windows dry as dust particles might damage the surface! Only clean acrylic glass windows with plenty of warm water, some dish washing liquid and a soft cloth.
Care 12.1.6 12 Waste water tank Clean the waste water tank after every use of the caravan. Cleaning: 12.2 EN Thoroughly rinse out the waste water tank with fresh water. Interior care Caravan - 11-06 - DET-0030-05 Open the cleaning opening on the waste water tank and the drain cock. If possible, treat stains immediately. Acrylic glass windows are delicate and require very careful handling (see section 12.1.3).
12 Care 12.3 Clean PVC-floor covering with special cleansing agents. Do not place carpet on wet PVC-floor covering. The carpet and the PVC-floor covering may stick together. Never clean the sink or the gas cooker with a scourer. Avoid anything which may cause scratching or grooves. Clean gas cooker only with a moist cloth. Prevent any water from penetrating the gas cooker. Water may damage the gas cooker.
Care 12.5 12 Winter care De-icing salt damages the underbody and the parts open to water spray. Dethleffs recommends to wash the vehicle more frequently during wintertime. Mechanical and surface treated parts and the underside are under particular strain, and should therefore be cleaned thoroughly. 12.5.1 If there is any risk of frost, cover the outside surface of the windows with winter insulation mats.
12 Care 12.6 12.6.1 Lay-up Temporary lay-up If the vehicle has been stationary for a long period (approx. 10 months) have the braking and gas systems checked by an authorised specialist workshop. Take into consideration that water is undrinkable after only a short time. Animal damage to cables can lead to short circuits. Fire hazard! Animals (especially mice) can cause great damage to the interior of the vehicle. This is especially true if the animal remains undisturbed in a parked vehicle.
Care Activities Gas system 12 Done Close regulator tap on the gas bottle Close all gas isolator taps Always remove gas bottles from the gas bottle compartment, even if they are empty Electrical system Fully charge living area battery Charge the battery for at least 20 hours before laying up. Spray the contacts on the thirteen-pin connector with contact spray Water system 12.6.2 Empty the entire water system. Blow out the residual water from the water pipes (0.5 bar max.).
12 Care 12.6.
Maintenance Chapter overview 13 13Maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle. The maintenance instructions address the following topics: 13.1 stabiliser braking system Alde hot-water heater replacing bulbs and fluorescent tubes spare parts Inspection work Like any technical appliance, the vehicle must be inspected at regular intervals. This inspection work must be carried out by qualified personnel.
13 Maintenance 13.3.2 AKS 3004 Fig. 169 Stabilising handle Checking the stabilising device (on the side of the friction pads) Prerequisite: Connection to AKS 3004, ball diameter 50 mm 13.3.3 Open the stabilising handle (Fig. 169,1). Close the stabilising handle until a resistance can be felt (the friction pads lie on the ball, they have not been tightened yet). If the arrow on the pressure pad (Fig. 170,3) is in front of or on the marked surface (Fig.
Maintenance 13.4 13 When the pin (Fig. 172,2) is in the longitudinal hole at the marking with the "+", the friction pads are still in good condition. When the pin is at both centre markings, the friction pads are slightly worn. When the pin is at the marking with the "–", the friction pads are worn and must be replaced. It is not possible to reset the friction pads. Braking system BPW/AL-KO chassis Have maintenance work on the braking system carried out by a specialist workshop.
13 Maintenance 13.5.1 Checking the fluid level Fig. 173 Compensator reservoir hotwater heater 13.5.2 Check if the fluid level is between the marks "MIN" (Fig. 173,3) and "MAX" (Fig. 173,2) on the compensator reservoir (Fig. 173). Topping up heating fluid 13.5.3 Switch off the hot-water heater and allow it to cool down. Position the vehicle horizontally. This prevents the formation of bubbles. Switch off the hot-water heater and allow it to cool down. Remove panel.
Maintenance 13.6 Close bleeding valve. Repeat this procedure at all bleeding valves. Check to see if the hot-water heater warms up. Replacing bulbs and fluorescent tubes 13.6.1 13 Bulbs and light fittings can be extremely hot. Therefore, allow lights to cool down before changing bulbs. Store bulbs in a safe place inaccessible to children. Do not use any bulb that has been dropped or which shows scratches in its glass. The bulb might burst. Lights can get very hot.
13 Maintenance 13.6.2 Spotlight (with glare protection) Fig. 176 Spotlight (with glare protection) Changing bulbs: 13.6.3 Pull the halogen bulb (Fig. 176,1) out of the socket (Fig. 176,3) or unscrew the bulb. Press the new halogen bulb into the socket between the two spring tongues (Fig. 176,2) or screw in the bulb. Halogen spotlight (movable) Fig. 177 Halogen spotlight (movable) Changing bulbs: 162 Loosen the fixing screws (Fig. 177,1). Carefully remove the lamp chalice (Fig.
Maintenance 13.6.4 13 Halogen spotlight (with glass shade) Fig. 178 Halogen spotlight (with glass shade) Changing bulbs: 13.6.5 Pull the halogen bulb (Fig. 178,1) forward out of the socket. Press the new halogen bulb into the fitting between the two spring tongues. Room lamp Fig. 179 Room lamp Changing bulbs: 13.6.6 Unscrew the cap (Fig. 179,1). Remove cover (Fig. 179,2). Press the light covering (Fig. 179,3) lightly together and remove it. Remove the fluorescent tube.
13 Maintenance Changing bulbs: 13.6.7 Use a suitable tool (e.g. a screwdriver) to carefully lever out the cover (Fig. 180,2) at the notch (Fig. 180,1) and remove it. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. Cooker lamp in the extractor hood Fig. 181 Cooker lamp Changing bulbs: 13.6.8 Press the cover (Fig. 181,1) lightly together with both hands. Remove cover. Change the fluorescent tube. Reassemble the lamp in the reverse order.
Maintenance 13.6.9 13 Surface-mounted halogen light (swivelling) Fig. 184 Surface-mounted halogen light (swivelling) Changing bulbs: 13.6.10 Use a suitable tool (e.g. a screwdriver) to lever out and remove the cover (Fig. 184,1). Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. Surface-mounted halogen light (flat) Fig. 185 Surface-mounted halogen light (flat) Changing bulbs: Caravan - 11-06 - DET-0030-05 EN Turn cover ring (Fig.
13 Maintenance 13.6.11 Indirect lights Fig. 186 Indirect lights Changing bulbs: 13.6.12 Remove the fixing screws (Fig. 186,1) on the panel (Fig. 186,2). Remove halogen bulb. Put in a new halogen bulb. Install the panel in the reverse order. Light column Fig. 187 Light column Changing bulbs: 13.7 Remove trays (Fig. 187,2). Compress the lamp glass (Fig. 187,1) lightly and remove. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order.
Maintenance 13 Fig. 188 Wardrobe light with opened battery compartment Changing the battery: 13.8 Carefully push back the retaining clip (Fig. 188,3) on the top side of the wardrobe light (Fig. 188,5). This exposes the nose (Fig. 188,4) on the retaining clip. Pull the battery holder (Fig. 188,2) out at the top. Take the button cell (Fig. 188,1) out of the battery holder. Insert new button cell of the same type (+/-), observing the correct polarity.
13 Maintenance The vehicle described in this instruction manual is built and equipped to factory standards. Special equipment is offered depending on its purpose or use. When fitting special equipment check if such equipment has to be entered in the vehicle documents. Observe the max. permissible gross weight. Your Dethleffs dealer will be pleased to advise you. 13.
Wheels and tyres Chapter overview 14 14Wheels and tyres This chapter contains instructions regarding the tyres of the caravan. The instructions address the following topics: tyre selection handling of tyres changing wheels spare wheel support At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle. 14.1 General Check tyre pressure before a journey or every 2 weeks.
14 Wheels and tyres Fig. 190 Tighten the wheel nuts or wheel bolts cross-wise 14.2 Check regularly that the wheel nuts or wheel bolts are firmly seated. Retighten the wheel nuts or wheel bolts of a changed wheel cross-wise (Fig. 190) after 50 km (30 miles). When using new or newly painted rims, re-tighten the wheel nuts or wheel bolts once again after approx. 1,000 to 5,000 km (600 miles to 3,000 miles).
Wheels and tyres 14.3 215/70 R 15C 109/107 Q 14.4 Tyre specifications Description Explanation 215 Tyre width in mm 70 Height-to-width proportion in percent R Tyre design (R = radial) 15 Rim diameter in inches C Commercial (transporter) 109 Load index code for single tyres 107 Load index code for twin tyres Q Speed index (Q = 160 km/h) Handling of tyres 14.5 14.5.1 14 Drive over kerbs at an obtuse angle. Otherwise the flanks of the tyres may get pinched.
14 Wheels and tyres 14.5.2 14.5.3 If alloy wheel rims are mounted and a steel spare wheel is mounted after a puncture: Do not drive any further than necessary (car dealer, car workshop, tyre dealer). Only drive at a suitable speed. The different wheels affect driving handling. Do not damage the thread of the thread bolts when changing the wheel. Tighten the wheel nuts or wheel bolts cross-wise (Fig. 190). See section 14.5.2 for tightening torque. When changing wheels (e.g.
Wheels and tyres Fig. 191 Securing support wheel Preparing the connected caravan: Preparing the disconnected caravan: Caravan - 11-06 - DET-0030-05 EN Fig. 192 Securing vehicle Loosen the stabilising device in caravan couplings with stabilising devices. Otherwise the friction pads will be highly loaded. Pull the handbrake of the towing vehicle and go to first gear or reverse gear. Park the vehicle on as even and stable a surface as possible. Apply the handbrake.
14 Wheels and tyres 14.5.4 Crank down the vehicle jack and remove it. Using the wheelbrace, tighten the wheel bolts evenly. The target value of the tightening torque of the wheel bolts is 90 Nm for steel wheel rims or 110 Nm for alloy wheel rims. Changing a wheel at alloy wheel rims 14.6 Screw in the wheel bolts and slightly tighten them cross-wise. The resting surfaces must be clean and free of burrs.
14 Wheels and tyres As a rule of thumb it can be assumed that a filled tyre loses pressure at a rate of 0.1 bar every two months. To prevent the tyres becoming damaged or burst, check the tyre pressure regularly. The information on pressure levels is valid for cold tyres and loaded vehicles. Pressure in hot tyres must be 0.3 bar higher than in cold tyres. Recheck the pressure when the tyres are cold. Tyres Max.
14 176 Wheels and tyres Caravan - 11-06 - DET-0030-05 EN
Troubleshooting Chapter overview 15 15Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies.
15 Troubleshooting See chapter 9 for changing the fuses. Fault Cause Remedy Road light system does no longer work correctly Bulb is defective Unscrew cover of the relevant light, replace bulb.
Troubleshooting 15 Fault Cause Remedy No voltage from the living area battery (Power Pack SE) The living area battery is discharged Charge living area battery immediately Total discharge damages the battery. If the vehicle is to be laid up for a long period, fully charge the living area battery beforehand Discharging is caused by inactive appliances (see chapter 9) Extractor hood does not work 15.
15 Troubleshooting 15.5 15.5.1 15.5.2 Cooker Gas cooker/gas oven Fault Cause Remedy Ignition fuse does not operate (flame does not burn after the control knobs are released) Heat-up time is too short Keep control knob pressed for approx. 15 to 20 seconds after ignition Ignition fuse is defective Contact customer service Flame extinguishes when being reduced to its minimum setting Thermocouple sensor is incorrectly set Correctly reset thermocouple sensor (do not bend).
Troubleshooting 15.6.
15 Troubleshooting 15.7 Refrigerator In the event of a defect contact the nearest customer service workshop of the relevant appliance manufacturer. The list of addresses is enclosed with the accompanying appliance documentation. Only authorised qualified personnel may repair the appliance.
Troubleshooting 15 Fault Cause Remedy Air conditioning unit does not warm up No 240 V power supply Connect 240 V power supply Temperature above 40 °C Temperature has been set incorrectly Adjust the temperature Thermostat defective Contact customer service Drainage holes for condensation are clogged Clean air conditioning unit Seal is defective Contact customer service Fault Cause Remedy Leakage water inside the vehicle A leak has occurred Identify leak, re-connect water pipes No water
15 Troubleshooting 15.
Special equipment 16.1 Weight details for special equipment 16 16Special equipment The use of accessories, parts and fittings not supplied by Dethleffs may cause damage to the vehicle and jeopardize road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product. Every alteration of the original condition of the vehicle can alter road behaviour and jeopardize road safety.
16 186 Special equipment Item designation Surplus weight (kg) Folding bed 19 Air conditioning unit (Dometic) 40 Refrigerator with freezer compartment 2 Microwave oven 15 Repair kit 1 Rack, satellite unit 6 Radio preparation 4 Satellite unit with hinged mast (BAS 60) 8 Satellite unit 19-24 Satellite antenna mast 2 Stabiliser 6 Stabilising supports 3 Bunk bed 10 Awning light 1 Hot-air system 10 Hot water supply with boiler 25 Hot water supply with hot water source 15 Wat
Helpful notes Chapter overview 17 17Helpful notes This chapter contains helpful tips on how to travel with the caravan. The instructions address the following topics: road assistance in European countries traffic rules in European countries gas supply in European countries toll regulations in European countries safe ways to spend the night during travel camping in winter At the end of the chapter there is a checklist containing the most important equipment for your trip with the caravan.
17 Helpful notes Country Greece Emergency services Police 112 171/112 Great Britain Ireland Breakdown service ELPA 104 00 1) 112 112 AA (08 00) 0 28 90 18/ (08 00) 82 82 82 1) 999/112 1) AA Dublin 18 00 66 77 88 999/112 1) Iceland 112 F.I.
17 Helpful notes Country Emergency services Police Slovakia 155/112 1) Breakdown service ASA 1 81 24 158/112 1) Slovenia Spain 112 113 AMZS (1) 9 87/ (003861) 5 30 53 53 1) 061 RACE 9 15 94 93 47 112 Czech Republic 155/112 1) UAMK CR 12 30 158/112 1) Turkey 112 – 155/112 1) Ukraine 03 112 UA (8-032) 2 97 81 12 02 Hungary 104/112 1) MAK 1 88/(06-1) 13 45 17 55 1) 107/112 1) Cyprus 199/112 1) AA 02 22 31 31 31 199/112 1) 1) In the mobile communication network Date 05/2006 Specifi
17 Helpful notes Country 2) 3) 4) 5) 6) 7) 8) 190 Outside built-up areas Motorway Ireland 48 80/100 1) 120 2) Iceland 50 80 – Italy 50 70 80 Croatia 50 80 80 Latvia 50 80 80 Lithuania 50 70 110 2) Luxembourg 50 75 90 50/60 80 80 Netherlands 50 80 80 Norway 50 60 8)/80 60 8)/80 Austria 50 100 9) 100 9) Poland 60 70/80 1) 80 Portugal 50 70/80 10) 100 Romania 50 80 100 Russia 50 70 90 11) Sweden 50 80 12) 80 12) Switzerland 50 80 80 2)
Helpful notes 17 9) With trailer of over 750 kg (max. perm. gross weight of 3.5 t), the following applies: On highways 80 km/h, on motorways 100 km/h. For towing vehicles over 3.5 t perm.
17 Helpful notes 17.5 Sleeping in the caravan away from camping areas Country Sleeping on privately owned lands Yes Yes No Belgium X Bulgaria X Comments No X On highway rest areas max. 24 hours permitted X Denmark X X On streets and squares only up to 11 hours with a parking disc Germany X X Staying overnight for one night to restore driving ability is permitted.
Helpful notes Country Sleeping on roads and fields Sleeping on privately owned lands Yes Yes No X X Romania X X Russia X X X Switzerland X Serbia and Montenegro X Slovakia X Slovenia Comments No Portugal Sweden 17 Staying overnight for one night on motorway service stations and car parks under 10 hours are tolerated X Not on agriculture areas or in the vicinity of houses.
17 Helpful notes 17.7 Use blue bottles from the firm Campingaz (distributed world-wide). Only use gas bottles with safety valves. When bottles from other countries are used, check the gas bottle compartments to see if the gas bottles fit into them. Gas bottles from other countries do not always display the same size as your own gas bottles. Toll regulations in European countries Many European countries have introduced a mandatory toll system.
Helpful notes 17.10 17 Make sure the air circulation is good. Good air circulation prevents moisture from collecting and makes it easier to heat the living area. Follow the instructions in the section "Gas supply in European countries". Use a two-bottle system with automatic controller for the gas system, so that the supply does not run out during the night. Only operate the gas system using propane gas. Do not use the space behind the heater as a storage compartment.
17 Helpful notes Living area Vehicle/tools Outside 196 Object Object Object Dustbin Insect lamp Rain clothes Road atlas Insect repellent First aid kit Bath towels Deck of cards Travel guides/parking guide Bath shoes Broom Rucksack Batteries Candles Sleeping bags Bed sheets Dust pan Pencils and paper Bed linen Coat-hangers Shoes Laundry bag Clothes brush Shoe polish Books Pillow Vacuum cleaner Camping guide Map Flash light Spare bulbs Medicine Pocket knife Water bott
Helpful notes Documents Caravan - 11-06 - DET-0030-05 EN 17 Object Object Object List of addresses Registration book Identity card Registration confirmation(s) Driving licence Passport Allergy certificate Green insurance card Writ of protection Instruction manuals Vaccination certificate Vignette/toll card Instruction leaflets for medicines Credit card Visa 197
17 198 Helpful notes Caravan - 11-06 - DET-0030-05 EN
Index 12 V fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 At the vehicle (self-sufficiency package) . . . 98 For Thetford toilet . . . . . . . . . . . . . . . . . 98, 99 On the power pack . . . . . . . . . . . . . . . . . . . 98 On the transformer/rectifier EBL 109 . . . . . 98 12 V indicator lamp . . . . . . . . . . . . . . . . . . . . . . 95 12 V main switch . . . . . . . . . . . . . . . . . . . . . . . . 95 12 V power supply . . . . . . . . . . . . . . . . . . . . . . .
Index Caravan Correct loading . . . . . . . . . . . . . . . . . . . . . . . 31 Pitching . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Caravan coupling . . . . . . . . . . . . . . . . . . . . . . . . 26 EM 150 R . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 WS 3000 D . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Caravan load . . . . . . . . . . . . . . . . . . . . . . . . 29, 32 Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Blind . . . . . . . . .
Index Driving in reverse . . . . . . . . . . . . . . . . . . . . . . . Driving with the caravan . . . . . . . . . . . . . . . . . . Duomatic switching facility . . . . . . . . . . . . . . . . During the journey . . . . . . . . . . . . . . . . . . . . . . . 39 39 83 39 E Electrical system . . . . . . . . . . . . . . . . . . . . . . . . 87 240 V connection, troubleshooting . . . . . . 178 Explanation of terms . . . . . . . . . . . . . . . . . . 87 Lighting, troubleshooting . . . . . . . . . . . . . .
Index Gas odour . . . . . . . . . . . . . . . . . . . . . . 22, 79, 179 Gas oven . . . . . . . . . . . . . . . . . . . . . . . . . 122, 123 Switching off . . . . . . . . . . . . . . . . . . . . 122, 124 Switching on . . . . . . . . . . . . . . . . . . . . . . . . 124 Troubleshooting . . . . . . . . . . . . . . . . . . . . . 180 Gas supply in European countries . . . . . . . . . . 193 Gas system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Defect . . . . . . . . . . . . . . . . . . . . . . .
Index Initial start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 After temporary lay-up . . . . . . . . . . . . . . . . 156 After winter lay-up . . . . . . . . . . . . . . . . . . . 156 Inner door, troubleshooting . . . . . . . . . . . . . . . 184 Insect screen, cleaning . . . . . . . . . . . . . . . . . . 152 Insect screen, conversion door Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Overload protection . . . . . . . . . . . . . . . . . . . . . . 92 Overrun brake . . . . . . . . . . . . . . . . . . . . . . . . . . 26 P Panel LT 109 (Power Pack SE) . . . . . . . . . . . . . 94 Panel see also displays . . . . . . . . . . . . . . . . . . . 94 Payload . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28, 29 Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Composition . . . . . . . . . . . . . . . . . . . . . . . . . 30 Example calculation . . . . . . . . . . .
Index Seating group with two single beds . . . . . . . 77 Widening the bed into a playing area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75, 76 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . 174 Spare wheel support . . . . . . . . . . . . . . . . . . . . 174 Special equipment . . . . . . . . . . . . . . . . . . . . . . 185 Description . . . . . . . . . . . . . . . . . . . . . . . . . 15 Marking . . . . . . .
Index Thetford toilet . . . . . . . . . . . . . . . . . . . . . . . 183 Water supply . . . . . . . . . . . . . . . . . . . . . . . 183 TV cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Tyre change see changing wheels . . . . . . . . . . 171 Tyre specifications . . . . . . . . . . . . . . . . . . . . . . 171 Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169 Excessive wear . . . . . . . . . . . 21, 36, 169, 174 General instructions . . . . . . . . . . . . . . . .
