Instruction manual Congratulations Instruction manual We congratulate you on your new motorhome and would like to thank you for choosing a quality product from Dethleffs.
Instruction manual Motorcaravan - 09-08 - DET-0033-07 EN
Contents 1 Guarantee . . . . . . . . . . . . . . . . . . . . . 7 1.1 1.2 1.3 1.4 Guarantee certificate. . . . . . . . . . . . . . . 7 Guarantee conditions . . . . . . . . . . . . . . 7 Inspection records. . . . . . . . . . . . . . . . . 9 Inspection plan for annual inspection . . . . . . . . . . . . . . . . . . . . . . 12 Inspection plan for water ingress test . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1.5 5.4 5.4.1 5.5 5.13 5.14 5.14.1 5.14.2 5.15 5.16 5.17 Seat belts. . . . . . . . .
Contents 7.2 7.2.1 7.2.2 7.2.3 7.3 7.4 7.4.1 7.4.2 7.4.3 7.4.4 7.4.5 7.4.6 7.4.7 7.5 7.5.1 7.5.2 7.5.3 7.5.4 7.5.5 7.6 7.7 7.7.1 7.7.2 7.7.3 7.7.4 7.7.5 7.7.6 7.8 7.9 7.10 7.11 7.11.1 7.12 7.12.1 7.12.2 7.12.3 7.12.4 7.12.5 7.13 7.13.1 7.13.2 7.13.3 7.13.4 7.13.5 7.13.6 7.13.7 4 External flaps . . . . . . . . . . . . . . . . . . . . 65 Flap lock with recessed handle . . . . . . 65 Flap lock, elliptical-shaped. . . . . . . . . . 65 Sliding drawer . . . . . . . . . . . . . . . . . . . 66 Ventilation . . .
Contents 9.9.3 9.9.4 9.9.5 9.9.6 9.9.7 9.9.8 9.10 9.10.1 9.10.2 9.11 9.11.1 9.11.2 Batteries gauge . . . . . . . . . . . . . . . . . Tank gauge . . . . . . . . . . . . . . . . . . . . Alarms . . . . . . . . . . . . . . . . . . . . . . . . Temperature display . . . . . . . . . . . . . Clock gauge . . . . . . . . . . . . . . . . . . . Switch for tank heater . . . . . . . . . . . . 240 V power supply. . . . . . . . . . . . . . 240 V connection . . . . . . . . . . . . . . .
Contents 12.6.2 12.6.3 Winter lay-up . . . . . . . . . . . . . . . . . . . 212 Starting up the vehicle after a temporary lay-up or after lay-up over winter . . . . . . . . . . . . . . . . . . . . 213 13 Maintenance . . . . . . . . . . . . . . . . . 215 13.1 13.2 13.3 13.3.1 13.3.2 13.3.3 13.4 13.5 13.5.1 13.5.2 13.6 Inspection work . . . . . . . . . . . . . . . . . 215 Maintenance work . . . . . . . . . . . . . . . 215 Alde hot-water heater. . . . . . . . . . . . . 215 Checking the fluid level . . . .
Guarantee 1.1 Guarantee certificate 1 1Guarantee Vehicle data Model: Car manufacturer/type of engine: Serial number: Initial registration: Purchased from company: Expiry of the guarantee period: Key number: Chassis number: Customer Address Surname, Christian name: Street, No.: Postal code, town: Dealer's stamp and signature We reserve the right to alter the construction, equipment and the scope of delivery. Special equipment is also listed that is not included in the standard scope of delivery.
1 Guarantee 3. The prerequisite for this guarantee is that the vehicle must be presented once a year to an authorised specialist workshop for an inspection. The presentation must take place 2 months at the latest after the anniversary of the initial registration (or delivery). If the inspection is not carried out according to schedule, this will nullify your warranty. It cannot be renewed by carrying out an inspection at a later time.
Guarantee 1.3 1 Inspection records Delivery Date: Signature and stamp of the Dethleffs dealer: 1st year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 1st year Water ingress test 1st year No defects found Found defects: Should it be determined during an inspection that additional work is necessary, then the carrying out of this work is dependent on the customer commissioning this to be done.
1 Guarantee 2nd year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 2nd year Water ingress test 2nd year No defects found Found defects: 3rd year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
Guarantee 4th year 1 Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here. Water ingress test 4th year Water ingress test 4th year No defects found Found defects: 5th year Water ingress test Date: Signature and stamp of the Dethleffs dealer: Paste inspection stamp here.
1 Guarantee 1.4 Inspection plan for annual inspection Pos. Component Activity Interval 1 Skylights Remove the inside frame of the skylights and tighten the screw connections of the securing clips 1.
Guarantee 1 Pos. Component Activity 1.5 Side wall floor plateau left connection Visual check 1.6 Connection to driver's cabin Visual check 1.7 Base frame with base frame cut-outs Visual check 1.8 Check the status of the outer metal sheets Visual check 1.9 Check the status of the window rubbers, expansion joints, sealing joints Visual check 2.
1 14 Guarantee Motorcaravan - 09-08 - DET-0033-07 EN
Introduction 2 Please read this instruction manual completely before using the vehicle for the first time! 2Introduction Always keep this instruction manual in the vehicle. Also inform all other users of the safety regulations. The non-observance of this symbol can lead to personal injury. The non-observance of this symbol can lead to damage being caused to, or inside the vehicle. This symbol indicates recommendations or special aspects.
2 Introduction The reprinting, translation and copying, including extracts is not permitted without prior written authorisation from the manufacturer. 2.1 General The vehicle is constructed in accordance with the latest technology and the recognised safety regulations. Nevertheless, personal injury may result and the vehicle may be damaged if the safety instructions in this instruction manual are not followed. Only use the vehicle in a technically impeccable condition.
Introduction Motorcaravan - 09-08 - DET-0033-07 EN 2 When parked, do not allow the engine to run more than necessary. When running idle, a cold engine releases more contaminants than usual. The running temperature of the engine is achieved more quickly whilst the vehicle is in motion. Use an environmentally-friendly WC chemical agent for the WC which can also be biologically degraded and only use small doses.
2 18 Introduction Motorcaravan - 09-08 - DET-0033-07 EN
Safety 3 Chapter overview 3Safety This chapter contains important safety instructions. The safety instructions are for the protection of persons and property. The instructions address the following topics: 3.1 3.1.1 Fire prevention Avoidance of fire risks 3.1.2 Never leave children in the vehicle unattended. Keep flammable materials clear of heating and cooking appliances. Lights can get very hot.
3 Safety 3.2 General 3.3 The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances. That is why the oxygen needs to be replaced on a constant basis. For this purpose, forced ventilation options (e.g. skylights with forced ventilation, mushroom-shaped vents or floor vents) are fitted to the vehicle. Never cover or block forced ventilations from the inside or outside with objects such as e.g. a winter mat.
Safety Motorcaravan - 09-08 - DET-0033-07 EN 3 Before commencing the journey, secure the hinged pull-down bed. Before commencing the journey, open and secure the shades on the windscreen and on the driver's and front passenger's windows. Before commencing the journey, rotate all swivel seats in the direction of travel and lock in position. During the journey, the swivel seats must remain locked in place in the direction of travel.
3 Safety 3.4 3.5.1 Before commencing the journey, put the antenna in park position. During the initial journey and each time after changing a wheel, re-tighten the wheel bolts/wheel nuts after 50 km (30 miles). Subsequently inspect them at regular intervals in order to ensure that they are firmly seated. Tyres may not be older than 6 years as the material becomes brittle over time (see chapter 14).
Safety 3.5.2 EN Open a window or skylight before taking open sources of combustion (gas cooker) into service. Do not use the gas cooker or gas oven for heating purposes. If the vehicle or gas devices are not used, close the regulator tap on the gas bottle. If there are several gas devices, each gas device must have its own gas isolator tap. If individual gas devices are not in use, close the respective gas isolator tap.
3 Safety 3.6 Only use special gas pressure regulators with a safety valve designed for vehicle use. Other gas pressure regulators are not permitted and cannot meet the demanding requirements. Use the gas pressure regulator defroster if the temperature falls below 5 °C. Use only 11 kg or 5 kg gas bottles. Camping gas bottles with built-in check valve (blue bottle with max. 2.5 or 3 kg content) are can be used in exceptional cases with a safety valve.
Before the journey Chapter overview 4 4Before the journey This chapter contains important information which has to be noted before commencing your journey or carrying out any tasks before the journey.
4 Before the journey 4.2 Registration Your motorhome is a vehicle which must be registered. Observe national regulations on registration. Please remember that certain countries require a separate national code sticker in addition to the EU plate. 4.3 Payload Overloading the vehicle and wrong tyre pressure can cause tyres to burst. You can lose control of the vehicle.
4 Before the journey 4.3.1 Terms Maximum permissible gross weight in a laden condition Technically speaking, the term "mass" has now replaced the term "weight". However, "weight" is still the term more frequent in common use. For better understanding, "mass" is therefore only used in the following sections for fixed formulations. All specifications according to EU norm DIN EN 1646-2. The maximum permissible gross weight in a laden condition is the weight that a vehicle may never exceed.
4 Before the journey You will find explanations on the individual components of the payload in the following text. Conventional load The conventional load is the weight specified by the manufacturer for the passengers. Conventional load means: 75 kg are calculated for every seat specified by the manufacturer, regardless of how much the passengers actually weigh.
Before the journey 4.3.2 4 Calculating the payload The payload calculation at the factory is partly based on all-inclusive weights. For safety reasons, the maximum permissible gross weight in a laden condition must not be exceeded. Only the maximum permissible gross weight and the mass in a ready-todrive condition, not the actual weight of the vehicle, is stated in the vehicle documents.
4 Before the journey The result is the weight that is permitted for the actual load of the personal equipment. 4.3.3 Loading the vehicle correctly For safety reasons, never exceed the maximum permissible gross weight in a laden condition. Distribute the load evenly on the left and right sides of the vehicle. Distribute the load evenly on both axles. In doing so, observe the axle loads specified in the vehicle documents.
4 Before the journey Calculating axle loads: Multiply the distance between storage compartment and front axle (A) with the weight of the load in the storage compartment (G) and divide the result by the wheelbase (R). The result is the weight of the load in the storage compartment on the rear axle. Make a note of this weight and of the storage compartment. In a second step, subtract the weight in the storage compartment (G) from the weight calculated beforehand.
4 Before the journey The vehicle roof is not suitable for localised load. Before stepping on to the roof, extensively cover the area you will be treading on. Materials with a smooth or soft surface are suitable, for example, a thick polystyrene panel. Secure roof loads with tension belts. Do not use rubber expanders. Observe the overall height of the vehicle when the roof rack is loaded. The driver's cabin should have a clearly visible notice stating the overall height.
Before the journey Depending on the vehicle equipment, clamping rails with clamping eyelets are mounted in the rear garage or in the rear storage space. Always secure loads onto the clamping eyelets. Always use tightening straps or lashing nets for securing the load, never rubber expanders. When clamping loads, always check that the clamping eyelets are placed tightly in the clamping rails.
4 Before the journey 4.3.8 Bike rack Observe the permissible axle loads and maximum permissible gross weight when loading the bike rack. Bicycles may not jut out beyond the maximum width of the vehicle. Adjust the attachments for the bikes accordingly. Load the bike rack with bicycles only (max. four units). Check the secure attachment of the bicycles on the bike rack after the first 10 km and then at each break in the journey. The identification plate and rear lights must not be covered.
Before the journey 4 The load rack and caravan coupling may not be used simultaneously. The load rack has a EG type approval number. Observe the country-specific regulations. Also read the manufacturer's instruction manual. The load rack permits transport of a load (e.g. a motor scooter or up to four bicycles) weighing up to 150 kg. Different attachments are available to transport the load. Our authorised dealers and service centres will be happy to advise you. Fig.
4 Before the journey 4.4 Turn the spring latch on both sides back half a turn and allow to engage. Care is to be taken when connecting and detaching a trailer. Risk of accident and injury! No persons are to be between the towing vehicle and the trailer during positioning for connecting and detaching. Observe the permissible nose weight and rear axle load of the towing vehicle. Nose weight and rear axle load must not be exceeded.
Before the journey 4.5.1 Mechanically operated entrance step If the entrance step has not been properly retracted and locked into place, a warning tone is heard when the ignition is switched on. Fig. 6 Pulling out: Pushing in: 4.5.2 4 Mechanically operated entrance step Pull the entrance step forwards (Fig. 6,2) until it latches into place. Slightly lift the entrance step (Fig. 6,1). Push the entrance step as far as it will go under the base of the vehicle (Fig. 6,3).
4 Before the journey Fig. 8 Extending: Retracting: Emergency operation Pull out the securing splint from the connection to the engine. Release the rectangular connection to the engine using a suitable object (e.g. a screwdriver). Push in the entrance step by hand and secure it using a suitable device (e.g. a string). Contact customer service. Shoes with pointed heels can leave permanent impressions in the PVCfloor covering. Never wear shoes with pointed heels in the vehicle.
Before the journey Fig. 9 Storing the television in the TV cabinet: 4.8 Television (flat screen) Fig. 10 4 Alternative: Television (flat screen) Rotate the television to its initial position (Fig. 9) and lock it into place. Use handle (Fig. 9,1) to push the holder for the flat screen backwards. The latch (Fig. 9,2) will engage. Close TV cabinet. Snow chains Only mount snow chains if there is a clearance of at least 50 mm between the tyres and the vehicle body.
4 Before the journey No.
Before the journey Gas system Electrical system No. Checks 33 Gas bottles firmly fixed in the gas bottle compartment so that they are unable to turn 34 Protective cap set on top of the gas bottle 35 Regulator tap on the gas bottle and gas isolator taps are closed 36 Check the battery voltage of the starter and living area battery (see chapter 9). If the panel indicates that the battery voltage is too low, the respective battery will need to be recharged.
4 42 Before the journey Motorcaravan - 09-08 - DET-0033-07 EN
5 During the journey Chapter overview 5During the journey This chapter contains instructions on how to drive the motorhome. The instructions address the following topics: 5.
5 During the journey 5.2 Driving speed 5.3 Uneven or one-sided loading affects road performance. Driving on unknown streets, you may encounter hazardous road conditions and unexpected driving situations. Therefore, in the interest of safety, make sure your driving speed is appropriate to any given driving situation and environment. Adhere to the national legal speed limits. Have defects on the braking system immediately remedied by an authorised specialist workshop. Avoid block brakings.
During the journey 5.4.1 5 After an accident, replace the seat belts. During the journey, do not tilt the backrest too far backwards. Otherwise the functionality of the seat belt is no longer guaranteed. Fastening the seat belt correctly Do not twist the belt. The belt must be positioned smoothly against the body. When fastening the seat belt, adopt the correct sitting position. The seat belt is fastened correctly when a fist can be passed between the body and the seat belt. 5.
5 During the journey Adjusting an appropriate seating position Move the armrest to the desired position. Turn the knurled wheel as far as possible in a clockwise direction. The position of the driver's and front passenger's seats can be adjusted. The handles which are required for this purpose are positioned to the front, right or left of the seat. Adjusting the seat height Turn the knurled wheel (Fig. 11,2) in an anticlockwise direction (when viewed from the front).
During the journey Adjusting the armrest For ease in handling, first move the armrest slightly upward. For fine adjustments, turn the handwheel (Fig. 13,1) upwards or downwards. Both the height and the position of the driver's and front passenger's seats can be adjusted. The handles which are required for this purpose are positioned to the front, right or left of the seat. 5.6 Rotating the seats in the pitched vehicle is described in chapter 7.
5 During the journey 5.7 Backrest adjustment mechanism for bench If the vehicle is equipped with the backrest adjustment, the bench cannot be converted into a bed. The inclination of the backrest can be adjusted with the backrest adjustment mechanism "Travel Lounge". Fig. 15 5.8 Backrest adjustment mechanism for bench Pull or press the bar (Fig. 15,1) under the seat (Fig. 15,3) upwards and hold it in this position. Push the seat on the rails (Fig.
During the journey 5.9 5 Branch block (model I) Fig. 17 Branch block The sliding regulator (Fig. 17,2) for the branch block (Fig. 17,1) is located on the outside left of the dashboard. Vehicle heating is coupled with room heater by the sliding regulator. Therefore the windscreen is heated when the vehicle is at a standstill.
5 During the journey 5.11 Electrically adjustable external mirrors (model I) Depending on the model, the vehicle is equipped with two electrically adjustable and heated external mirrors. The switches for external mirror adjustment and the mirror heater are on the dashboard. Fig. 19 Adjusting: Switching on the heater: 5.12 Select the mirror to be adjusted. To do so, turn the rotary switch (Fig. 19,1) to the left or right. Adjust the mirror by pressing the switch (Fig.
During the journey Fig. 22 Securing the Roman shade for the driver's / front passenger's window: 5.13 5 Locking mechanism for Roman shades on driver's/front passenger's windows On the Roman shades for the driver's and passenger's window, push the handle (Fig. 22,1) onto the cap. The Roman shade is secured. Writing and reading rest During the journey the writing and reading rest must be closed. If there is a passenger airbag, the writing and reading rest is locked so it cannot be opened.
5 During the journey 5.14.1 Model I Fig. 24 Opening: Closing: 5.14.2 52 Release knob on the outside of the bonnet Reach under the bonnet with one hand and actuate the safety hook (Fig. 25,1). Do this by reaching behind the plate (Fig. 25,2) and pulling it forward. Move the bonnet in an arch forwards and upwards. Move the bonnet in an arch downwards and backwards until the latch locks audibly in place. Check whether the bonnet is locked correctly.
During the journey 5.15 Filling washer fluid (model I) Fig. 27 5.16 5 Washer fluid container filler neck Unlock and open the bonnet. Remove the lid (Fig. 27,1) from the filler neck of the washer fluid container. Slowly fill in washer fluid. Push the lid onto the filler neck of the washer fluid container. Checking the oil level (model I) 1 Fig. 28 Oil dipstick Oil dipstick (I model) The oil dipstick (Fig. 28,1) is located behind the front crossbeam. The oil dipstick is marked in red. 5.
5 During the journey Fig. 29 Opening: Closing: 54 Cap for the fuel filler neck Insert the key in the locking cylinder (Fig. 29,1) and turn it in an anticlockwise direction. Remove cap. Place the cap on the fuel filler neck. Turn key in a clockwise direction. Remove the key. Check that the cap is fastened securely on the fuel filler neck.
Pitching the motorhome Chapter overview 6 6Pitching the motorhome This chapter contains instructions on how to pitch the vehicle. The instructions address the following topics: 6.1 handbrake entrance step wheel chocks operation of the supports 240 V connection refrigerator Pitch the vehicle so that it is as horizontal as possible. Secure the vehicle to prevent it from rolling. Animals (especially mice) can cause great damage to the interior of the vehicle.
6 Pitching the motorhome 6.4.2 Steady legs (SAWIKO) Depending on the model, the hexagonal nut has a joint, which can be used to bring the attached socket spanner into a more convenient position for turning. In order to ensure their correct function, clean and grease the interior tubes of the steady legs regularly. The length of the steady legs can be adjusted according to the model. Fig. 30 Extending: Retracting: 6.4.
Pitching the motorhome Fig. 31 Extending: Retracting: 6.5 6 Steady leg Place the socket spanner on the hexagon nut (Fig. 31,1) and rotate until the steady leg is in a perpendicular downward position. Remove the splint (Fig. 31,4) out of the support foot extension (Fig. 31,5). Extend the support foot extension until it has reached the required length. Insert the splint in the support foot extension.
6 58 Pitching the motorhome Motorcaravan - 09-08 - DET-0033-07 EN
Living Chapter overview 7 7Living This chapter contains instructions about living in the vehicle. The instructions address the following topics: 7.1 Doors 7.1.
7 Living Locking: 7.1.2 Insert the key into locking cylinder (Fig. 32,1) and turn until the door lock is engaged. Return the key to the central position and remove it. Conversion door, outside (with recessed handle) Fig. 33 Opening: Locking: 7.1.3 Insert the key into locking cylinder (Fig. 33,1) and turn until the door lock is unlatched. Return the key to the central position and remove it. Pull on the handle (Fig. 33,2). The door is open. Insert the key into locking cylinder (Fig.
Living 7.1.4 Conversion door, inside (with knob) Fig. 35 Opening: Locking: 7.1.5 Fig. 36 Door lock of conversion door, inside, locked Turn the door knob approx. 45° in a clockwise direction (Fig. 35,2) and leave in this position (Fig. 36). Conversion door, inside (with locking lever) Opening: Locking: EN Door lock of conversion door, inside, open Turn the knob in an anticlockwise direction (Fig. 35,1). The door lock is unlatched. Fig.
7 Living 7.1.6 Conversion door, inside (Hartal) Fig. 38 Opening: Pull on the handle (Fig. 38,1). The door lock is unlatched. Locking: Turn the safety knob (Fig. 38,2) in a clockwise direction. 7.1.7 Driver's door, outside Fig. 39 Opening: Locking: 62 Door lock of conversion door, inside Door lock of driver's door, outside Insert the key into locking cylinder (Fig. 39,1) and turn until the door lock is unlatched. Return the key to the central position and remove it.
Living 7.1.8 Driver's door, inside Fig. 40 Opening: Locking: 7.1.9 7 Door lock of driver's door, inside Pull on the handle (Fig. 40,2). The door lock is unlatched. The locking lever (Fig. 40,1) jumps out automatically. Press the locking lever (Fig. 40,1). Insect screen door, can be folded out An insect screen door is integrated in the conversion door. The insect screen door can be opened outward. In the process the conversion door stays open. Fig.
7 Living 7.1.10 Insect screen on the conversion door, extendable Open the insect screen completely before closing the conversion door. Fig. 43 Insect screen Closing: Pull out the insect screen completely by the bar (Fig. 43,1). Opening: Push the insect screen into its initial position by the bar (Fig. 43,1). 7.1.11 Window of conversion door (Hartal) The conversion door window is fitted with a Roman shade. Fig. 44 64 Closing: Opening: Roman shade Grasp the Roman shade (Fig.
Living 7.2 7 External flaps Before commencing the journey, close all external flaps and lock them. To open and close the external flap, open or close all locks that are fitted to the external flap. When leaving the vehicle, close all external flaps. The external flaps fitted to the vehicle are all fitted with identical locking cylinders. Therefore, all locks can be opened with a single key. 7.2.
7 Living Fig. 46 Opening: Closing: 7.2.3 Insert key into locking cylinder (Fig. 46,1) and turn a quarter turn in an anticlockwise direction. The lock handle (Fig. 46,2) snaps out. Remove the key. Turn lock handle one quarter turn in an anticlockwise direction. The flap lock is open. Firmly close the external flap. Turn lock handle in a clockwise direction until it is horizontal. The flap lock is now engaged but not locked. Insert key into locking cylinder.
Living 7.3 Ventilation Condensation 7.4 Although sufficient ventilation is provided, in certain weather conditions, condensation can form on metal objects (e.g. screwed connections in the floor). Additional cold spots can occur at thermal "bridges" (e.g. mushroomshaped vents, skylight edges, sockets, filler necks, flaps, etc.). Windows EN The oxygen in the vehicle interior is used up by breathing and the use of gas operated appliances.
7 Living 7.4.1 Sliding window with lock Fig. 48 Opening: Closing: 7.4.2 Pull out the lock (Fig. 48,1). Press handle (Fig. 48,2) and push it forward or backward at the same time. Open window half up to the required position. Close the window as far as it can go. Push in the lock. Sliding window without lock Fig. 49 Opening: Closing: 7.4.3 Sliding window Press handle (Fig. 49,1) and push or pull it forward or backward at the same time.
Living Fig. 50 Opening: Catch lever in "closed" position Fig. 51 7 Hinged window with rotary hinges, open Turn the catch lever (Fig. 50,3) a quarter turn towards the centre of the window. Open the hinged window until the required position has been reached and use knurled knob (Fig. 51,1) to secure in position. The hinged window remains locked in the required position. Closing: Turn knurled knob (Fig. 51,1) until the latch is released. Close the hinged window. Turn the catch lever (Fig.
7 Living 7.4.4 Hinged window with automatic hinges Open the window completely, to release the lock. If the locking device is not released and the window is closed nevertheless, there is the danger of the window breaking due to the massive counter-pressure. When opening the hinged windows, ensure that there are no torsional forces. Open and close the hinged windows evenly. Fig. 53 Opening: Catch lever in "closed" position Fig.
Living 7 To place the hinged window into the "continuous ventilation" position: Turn the catch lever (Fig. 55,3) a quarter turn towards the centre of the window. Slightly open the hinged window outwards. Turn the catch lever a quarter turn towards the window frame. The locking catch (Fig. 55,2) has to be moved into the recess of window catch (Fig. 55,1). During the journey, the hinged window may not be in "continuous ventilation" position.
7 Living Insect screen The insect screen is located in the upper blind box. Closing: Opening: 7.4.6 Pull insect screen at the handle (Fig. 56,1) down and hang it into the locking devices (Fig. 56,3) situated on both sides of the window frame. Press handle (Fig. 56,1) downwards and, at the same time, tilt it slightly inward. The insect screen can be taken out of the locking devices situated on both sides of the window frame. Use handle to return the insect screen slowly to its initial position.
Living 7.4.7 Roman shades for windscreen, driver's window and front passenger's window Fig. 58 Closing: Opening: 7.5 7 Roman shade for the windscreen Fig. 59 Roman shades for driver's window and front passenger's window On the Roman shade for the windscreen, push the locking knobs (Fig. 58,1) upwards or downwards. If the red dot is visible, the lock is open. Grasp the handle (Fig. 58,2 and Fig.
7 Living 7.5.1 Depending on the weather, close the skylights far enough to prevent moisture from entering. Do not climb on the skylights. Before commencing the journey, close the skylights. Before commencing the journey, check that the skylights are closed and locked. Before commencing the journey, open the blinds or Roman shades. Apply talc to the rubber seals of the skylights at least once a year. When leaving the vehicle, always close the skylights.
Living Blind Using both handles (Fig. 62,1), pull down the skylight with force until the two snap latches lock into place. Swing insect screen upwards (Fig. 61,1) until it latches in place. To close and open the blind: Fig. 63 Closing: Opening: 7.5.2 7 Blind Pull the blind (Fig. 63,1) using the handle (Fig. 63,2) and hook the hooks (Fig. 63,3) in the opening (Fig. 63,4). Pull the hooks (Fig. 63,3) out of the opening (Fig. 63,4) and guide the blind back.
7 Living 7.5.3 Hinged skylight The hinged skylight may be opened on one side only. Three inclination angles and a ventilation position are available. An extension hook is included as standard equipment. Fig. 65 Opening: Closing: Locking in the ventilation position: Roman shade Hinged skylight, lock Fig. 66 Hinged skylight Turn the lever (Fig. 65,1 or Fig. 66,3) one quarter turn. Grip lever and push hinged skylight upwards. Grip lever and pull hinged skylight downwards.
Living 7.5.4 7 Heki skylight (mini and midi) Fig. 67 Safety knob on the Heki skylight Fig. 68 Heki skylight, guide The Heki skylight is opened on one side only. Opening: Closing: Press the safety knob (Fig. 67,2) and pull the bar (Fig. 67,1) down with both hands. Pull the bar (Fig. 68,1) in the guides (Fig. 68,2) to the rearmost position (Fig. 68,3). Use both hands to push the bar (Fig. 68,1) slightly upwards. Push the bar back in the guides.
7 Living Opening: Insect screen Closing: Opening: 7.5.5 Slowly push the Roman shade at the handle to its initial position. To close and open the insect screen: Pull the insect screen by the handle to the opposite handle of the Roman shade. Press the rear part of the handle of the insect screen. The latch is released. Use handle to return the insect screen slowly to its initial position. Wind-up skylight Fig. 71 Wind-up skylight The wind-up skylight can be opened using the manual crank.
Living 7.6 7 Rotating seats Before commencing the journey, rotate all swivel seats in the direction of travel and lock in position. During the journey, the swivel seats must remain locked in place in the direction of travel. Setting the position of the seats and armrests is described in chapter 5. Move the seats all the way down before turning. Otherwise, the seats cannot be turned.
7 Living Extending: Reducing size: Undo the knurled screws (Fig. 74,2). Lift the table-top slightly and pull out it out as far as possible. The table extension (Fig. 74,1) is fully extended. Set down the table. Insert the table-top extension in the table extension. Lift the table-top slightly and push it back as far as possible. Tighten the knurled screws. Undo the knurled screws (Fig. 74,2). Slightly lift the front of the table-top and pull out.
Living 7.7.2 7 Suspension table (bar seating group) The suspension table size can be enlarged by pulling out a table-top extension. Fig. 77 Extending: Reducing size: Lock for table-top extension Fig. 78 Table-top extension Loosen knurled screw (Fig. 77,1). Pull out the table-top extension (Fig. 77,2) as far as possible (Fig. 78). Guide table-top extension (Fig. 78,1) upwards in a circular movement. The table-top extension lies flush with the table-top. Pull table-top extension (Fig.
7 Living 7.7.3 Swivel table for the round seating group Before commencing the journey, reduce the size of the swivel table and secure it. Fig. 80 Fastening to the floor: Lock for swivel table with clamp Fig. 81 Lock for swivel table without clamp Place the swivel table next to the holder (Fig. 80,3) or on the holder (Fig. 81,2). Place the bar (Fig. 80,2) with the securing bolt (Fig. 80,1) over the table leg.
Living 7.7.4 7 Fixed table (movable table-top) The top of the fixed table can be moved both lengthways and crossways. Fig. 84 Moving in a lengthways direction: Moving in a crossways direction: Fixed table Loosen knurled screw (Fig. 84,1). Move table-top (Fig. 84,2) to the desired position. Retighten the knurled screw. Loosen knurled screw (Fig. 84,3). Move table-top (Fig. 84,2) to the desired position. Retighten the knurled screw. The fixed table cannot be used as a bed foundation. 7.
7 Living Fig. 86 Fixed table (from below) The table-top of the fixed table can be moved lengthways or folded to the side. Moving in a lengthways direction: Folding the table-top to the side: Loosen the fixing screws (Fig. 86,2 and 3). Shift the table-top. Lock the table-top with the fixing screws. Remove the fixing screw (Fig. 86,1). Fold the table-top to the side. Fig. 87 Extending the fixed table Depending on the model, the table top of the fixed table can be enlarged.
Living Fig. 88 7 Lift-off table for the round seating group The lift-off table's lifting mechanism permits it to be used as a bed foundation. Conversion to bed foundation: 7.8 Press the table-top (Fig. 88,2) in the middle downwards to the desired stop limit (Fig. 88,1 or 4) and hold it down. Swivel the catch lever (Fig. 88,3) to the right. The lift-off table is locked. Television Flat screen in the TV cabinet Swivel the catch lever (Fig. 88,3) to the left. The lock is open.
7 Living Flat screen with jointed arm The flat screen is fastened to a jointed arm. Fig. 90 Positioning the flat screen with jointed arm: 7.9 Pull on the fabric strip (Fig. 90,3) to unlock the jointed arm (Fig. 90,2). Swivel flat screen (Fig. 90,1) into the required position. Take hold of the flat screen at the top and bottom edge with both hands and set the desired angle of inclination. Lamps Bulbs and light fittings can be extremely hot.
Living 7.10 7 Light switch The light switches have different layouts according to the model. The light switches are located either directly on the corresponding lamp or next to the lamp, e.g. in the vicinity of the seating group. Fig. 92 Light switch for lighting entrance Depending on the model, there is a light switch for lighting the entrance at the bottom of the entrance area (Fig. 92,1). 7.11 7.11.1 Extending the seating group Extending the central seating group 1 2 3 4 5 6 7 8 Fig.
7 Living 7.12 7.12.1 Beds Overcab bed The maximum permitted overcab bed load is 200 kg. Only use the overcab bed, if the safety net is set up. Never allow small children to remain in the overcab bed without supervision. But in particular with regard to small children less than 6 years of age, users should ensure that they cannot fall out of the overcab bed. Use separate children's beds or travel cots suitable for children. Do not load the overcab bed without mattress.
Living Fig. 96 Folding upwards: Folding downwards: 7.12.2 7 Overcab bed, folded upwards Lift the mattress forwards and set it down on the panel. Fold the front of the overcab bed (Fig. 96,1) upwards. The overcab bed is kept in the upper position by gas-pressure springs. Pull overcab bed downwards. If necessary, push the mattress behind the panel. Pull-down bed (model I) The maximum permitted pull-down bed load is 200 kg.
7 Living Variant 2 The seats of the central seating group in opposite direction to the direction of travel are equipped with headrests (safety package). The headrests on driver's and front passenger's seats can be removed. Variant 3 Remove the headrests. Turn the driver's seat to the direction of travel, lock it in place and move it backwards. Fold the backrest of the passenger's seat back. Push the front passenger's seat forwards and fold the backrest back completely.
Living Safety net Setting up: 7.12.3 7 The safety net is stored as standard between the mattress and slatted frame. Only use the safety net if persons are already in the pull-down bed. Fasten the retaining straps (Fig. 97,1) to the holders (Fig. 97,3) on the ceiling. Bunk bed The maximum permitted bunk bed load is 100 kg. Only use the bunk bed, if the safety net is set up. Never allow small children to remain in the bunk bed without supervision.
7 Living 7.12.4 Bunk bed (side) The maximum permitted bunk bed load is 100 kg. Only use the bunk bed, if the safety net is set up. Never allow small children to remain in the bunk bed without supervision. But in particular with regard to small children less than 6 years of age, users should ensure that they cannot fall out of the bunk bed. Use separate children's beds or travel cots suitable for children.
Living 7.12.5 7 Fixed bed (gas-pressure springs) Fig. 102 Fixed bed A storage compartment is underneath the bed. Lift up the slatted frame to place items in the storage compartment or to empty it from the inside of the vehicle. Opening: Closing: Motorcaravan - 09-08 - DET-0033-07 EN Lift the mattress forwards and set it down on the panel. Lift slatted frame. The gas-pressure springs (Fig. 102,1) hold the slatted frame open.
7 Living 7.13 Converting seating groups for sleeping 7.13.1 Depending on the model, the seating group can be different in shape and position to the one shown here. Depending on the model, an enclosed additional cushion must be inserted between the seat cushions. Central seating group 1 2 3 4 5 Back cushion Seat cushion Table Bar Mounting rail Fig. 103 Prior to conversion Fig. 104 After conversion 94 Convert the table (Fig. 103,3) to a bed foundation (see section 7.7).
Living 7.13.2 7 Central seating group with extension Fig. 105 Prior to conversion 1 2 3 4 5 6 7 8 9 10 Back cushion Seat cushion Table Mounting rail Flap Bench seat extension Bar Handle Additional cushion Additional cushion Fig. 106 During conversion Fig. 107 After conversion Motorcaravan - 09-08 - DET-0033-07 EN Extend the table (Fig. 105,3) and convert it into a bed foundation (see section 7.7). Insert the bar (Fig. 105,7) or pull it inwards.
7 Living 7.13.3 Central seating group with divan 1 2 3 4 5 Additional cushion Seat cushion Armrest Slatted frame Back cushion Fig. 108 Prior to conversion Fig. 109 During conversion Fig. 110 After conversion 96 Convert the central seating group for sleeping (see section 7.13.2). Remove the armrests (Fig. 108,3) of the divan and lay it aside. Pull out the slatted frame (Fig. 109,4). Pull the seat cushion (Fig. 110,2) to the central seating group. Remove the additional cushion (Fig.
Living 7.13.4 7 Round seating group (without slatted frame) 1 2 3 4 5 Back cushion Seat cushion Table Back cushion Back cushion Fig. 111 Prior to conversion Fig. 112 During conversion Fig. 113 After conversion Motorcaravan - 09-08 - DET-0033-07 EN Convert the table (Fig. 111,3) to a bed foundation (see section 7.7). Pull the seat cushions (Fig. 112,2) into the centre. Insert the back cushions (Fig. 112,1) between the seat cushions and the exterior wall. Remove the back cushions (Fig.
7 Living 7.13.5 Round seating group (with slatted frame) 1 2 3 4 5 Back cushion Seat cushion Table Back cushion Slatted frame Fig. 114 Prior to conversion Fig. 115 During conversion Fig. 116 After conversion 98 Convert the table (Fig. 114,3) to a bed foundation (see section 7.7). Pull out the slatted frames (Fig. 115,5). Pull the seat cushions (Fig. 115,2) into the centre. Insert the back cushions (Fig. 115,1) between the seat cushions and the exterior wall. Remove the back cushions (Fig.
Living 7.13.6 7 Front bench seat 1 2 3 4 5 6 Back cushion Seat cushion Table Driver's seat Additional cushion Guest bed foundation Fig. 117 Prior to conversion Fig. 118 After conversion Motorcaravan - 09-08 - DET-0033-07 EN Turn the driver's seat (Fig. 117,4) and push it all the way forward. Convert the table (Fig. 117,3) to a bed foundation (see section 7.7). If the vehicle has a guest bed foundation (Fig. 118,6), remove the back cushion (Fig. 117,1) and the seat cushion (Fig.
7 Living 7.13.7 Front bench seat with divan 1 2 3 4 5 6 7 8 9 Back cushion Seat cushion Table Back cushion Seat cushion Flap Bench seat extension Additional cushion Additional cushion Fig. 119 Prior to conversion Fig. 120 During conversion Fig. 121 After conversion 100 Extend the table (Fig. 119,3) and convert it into a bed foundation (see section 7.7). Pull the handle and open the flap (Fig. 119,6). Fold up the bench seat extension (Fig. 120,7) and wedge it with the flap.
Living 7.13.8 7 Front bench seat with divan (extendable) Fig. 122 Prior to conversion 1 2 3 4 5 6 7 8 9 10 Back cushion Seat cushion Bedding box extension Table Back cushion Seat cushion Flap Bench seat extension Additional cushion Additional cushion Fig. 123 During conversion Fig. 124 After conversion Motorcaravan - 09-08 - DET-0033-07 EN Extend the table (Fig. 122,4) and convert it into a bed foundation (see section 7.7). Pull the handle and open the flap (Fig. 122,7).
7 Living 7.13.9 Front seating group 1 2 3 4 5 6 Back cushion Seat cushion Table Seat cushion Back cushion Additional cushion Fig. 125 Prior to conversion Fig. 126 During conversion Fig. 127 After conversion 102 Convert the table (Fig. 125,3) to a bed foundation (see section 7.7). Pull the seat cushions (Fig. 126,2 and 4) into the centre. Insert the back cushions (Fig. 126,1 and 5) between the seat cushions and the exterior wall. Place the additional cushion (Fig.
Gas system 8 Chapter overview 8Gas system This chapter contains instructions regarding the gas system of the vehicle. The instructions address the following topics: safety gas consumption changing the gas bottles gas isolator taps external gas connection automatic switching facility The operation of the gas operation appliances of the vehicle is described in chapter 10. 8.
8 Gas system 8.2 Propane gas is capable of gasification up to -42 °C, whereas butane gas gasifies at 0 °C. Below these temperatures no gas pressure is available. Butane gas is unsuitable for use in winter. Regularly inspect the gas tube fitted to the gas bottle connection for tightness. The gas tube must not have any tears and must not be porous. Have the gas tube replaced by an authorised specialist workshop no later than ten years after the manufacturing date.
Gas system 8.3 EN Never block the floor ventilation openings below the gas bottles. With some models, the gas bottle compartment is located right next to the conversion door. With these models, only open the gas bottle compartment when the conversion door is closed. Danger from damages. For gas-operated units the gas pressure must be reduced to 30 mbar. Connect gas pressure regulator complete with safety valve directly to bottle valve.
8 Gas system Fig. 128 Gas bottle compartment Fig. 129 Gas bottle connection Depending on the model, the gas bottle holder can be pulled out of the gas bottle compartment: 8.5 Open external gas bottle compartment (see section 7.2). If there is a guard plate (Fig. 128,1), fold it down. Unlock the slide (Fig. 128,3) using the handle (Fig. 128,2). Pull out the slide (Fig. 128,3) as far as possible. Turn back the handle (Fig. 128,2). Close the regulator tap (Fig.
Gas system 8 A gas isolator tap (Fig. 130) for every gas device is built into the vehicle. The gas isolator taps can be found on the front of the cooker. 8.6 External gas connection If the external gas connection is not in use, always close the gas isolator tap. Only gas appliances with a suitable adapter should be connected to the external gas connection. Connect only external gas appliances which are designed for an operation pressure of 30 mbar.
8 Gas system The Duomatic is an automatic switching facility with a remote display for a twobottle gas system. The Duomatic switching facility automatically switches gas supply from the primary bottle to the reserve bottle as soon as the primary bottle is either empty or no longer ready for operation. The gas appliances may still continue operation. The Duomatic switching facility is suitable for all commercial gas bottles from 3 kg to 33 kg. Fig.
Gas system Putting into operation: Switching off: Remote display Motorcaravan - 09-08 - DET-0033-07 EN Use the knob (Fig. 132,6) on the switching regulator (Fig. 132,5) to select the gas bottle which is to be the primary source of gas (primary bottle). Always turn the knob as far as it will go. When the knob is in the red area, the gas is taken primarily from the gas bottle with the central regulator (Fig. 132,3).
8 110 Gas system Motorcaravan - 09-08 - DET-0033-07 EN
Electrical system Chapter overview 9 9Electrical system This chapter contains instructions regarding the electrical system of the vehicle. The instructions address the following topics: safety explanations of terms relating to the battery 12 V power supply living area battery loading the batteries transformer/rectifier panel 240 V power supply connection to the 240 V power supply fuse rating The operation of the electrical appliances of the housing body is described in chapter 10.
9 Electrical system The capacity of a battery is given in ampere hours (Ah). If a battery possesses a capacity of 80 Ah, then the battery can dispense a current of 1 A for 80 hours or a current of 2 A for 40 hours. External influences such as temperature may alter the storage capacity of the battery. 9.3 12 V power supply To disconnect all electrical 12 V appliances from the power supply, disconnect the living area battery from the 12 V power supply.
Electrical system 9 Before disconnecting or connecting the terminals of the battery, switch off the vehicle engine as well as the 240 V and 12 V power supplies and all appliances. Danger of short circuit! If the starter battery or living area battery are disconnected, do not apply the ignition. Danger of short circuit! Take note of the battery manufacturer's users and maintenance instructions. The battery is maintenance-free. Maintenance-free means: It is not necessary to check the acid level.
9 Electrical system 9.4 Charging the living area battery and starter battery The acid in the battery is poisonous and corrosive. Any contact with the skin or the eyes is to be avoided. In the case of charging with an external charger there is danger of explosion. Only charge the battery in a well ventilated area and away from naked flames or possible sources of sparks.
Electrical system 9.5 EN Disconnect the living area battery from the 12 V power supply. Disconnect the mains plug from the transformer/rectifier. Switch off all gas appliances, all gas isolator taps and close the regulator tap on the gas bottle. There is a danger of short circuit when disconnecting the battery poles. For this reason, first disconnect the negative terminal on the living area battery or the starter battery and then the positive.
9 Electrical system Fig.
Electrical system 9.5.1 9 Battery cut-off switch When the battery cut-off switch is OFF, the safety/drainage valve opens. The water flows out of the boiler. When the battery cut-off switch is ON again, close the safety/drainage valve of the boiler by hand. Also switch off a refrigerator with automatic power selection system. The refrigerator will otherwise switch to gas operation.
9 Electrical system Measures: 9.5.4 Switch off all electrical appliances that are not absolutely essential at the corresponding switch. If necessary, use the 12 V main switch to switch the 12 V power supply back on for a short while. This is only possible, however, when the battery voltage is above 11 V. If the voltage is below this level, the 12 V power supply cannot be switched on again until the living area battery has been recharged.
Electrical system 9 Fig.
9 Electrical system 9.6.1 Battery cut-off switch When the battery cut-off switch is OFF, the safety/drainage valve opens. The water flows out of the boiler. When the battery cut-off switch is ON again, close the safety/drainage valve of the boiler by hand. Also switch off a refrigerator with automatic power selection system. The refrigerator will otherwise switch to gas operation.
Electrical system Measures: 9.6.4 9 Switch off all electrical appliances that are not absolutely essential at the corresponding switch. If necessary, use the 12 V main switch to switch the 12 V power supply back on for a short while. This is only possible, however, when the battery voltage is above 11 V. If the voltage is below this level, the 12 V power supply cannot be switched on again until the living area battery has been recharged.
9 Electrical system Danger of total discharge (battery alarm) Battery voltage (values during operation) Mobile operation (vehicle moving, no 240 V connection) Battery operation (vehicle stationary, no 240 V connection) Power operation (vehicle stationary, 240 V connection) 11 V or less 1) 12 V power supply overload If appliances are switched off: Battery flat 12 V power supply overload The battery is not charged by the alternator, the alternator's regulator is defective 11.1 V to 13.
Electrical system Displays: 9.7.2 9 Press the upper part of the rocker switch (Fig. 136,5) " water is displayed. ": The volume of Press the lower part of the rocker switch (Fig. 136,5) " waste water is displayed. ": The volume of Battery alarm for the living area battery The red ALARM warning light (Fig. 136,7) flashes as soon as the voltage of the living area battery falls below 11 V (measured under operation) and there is a risk of a total discharge. 9.7.
9 Electrical system 9.8 Panel IT 992 1 2 3 4 5 6 7 8 9 V/tank gauge Current gauge 12 V indicator lamp 12 V main switch 240 V indicator lamp Rocker switch for special equipment Rocker switch for reading the level in the water or waste water tanks ALARM warning light for the living area battery Rocker switch for reading the battery voltage of the starter and living area batteries Fig. 137 Panel IT 992 9.8.
Electrical system Battery voltage (values during operation) Mobile operation (vehicle moving, no 240 V connection) Battery operation (vehicle stationary, no 240 V connection) Power operation (vehicle stationary, 240 V connection) 13.3 V to 13.7 V Battery is being charged (main charge) Occurs only briefly after charging Battery is being charged (main charge) 13.8 V to 14.4 V Battery being charged (float charge) – Battery being charged (float charge) Over 14.
9 Electrical system 9.8.3 If the battery voltage falls below 10.5 V, the battery monitor in the transformer/rectifier switches off all of the 12 V appliances, excluding the safety/ drainage valve. Current gauge for charging/discharging the living area battery The battery current actually flowing is permanently displayed on the current gauge (Fig. 137,2). The gauge automatically lights up as soon as a switch is pressed.
Electrical system 9.8.5 9 When leaving the vehicle, switch off the 12 V main switch. This prevents any unnecessary discharge of the living area battery. Appliances such as the safety/drainage valve, charger, solar charge regulator and panel consume approx. 20 mA to 65 mA of electricity from the battery capacity, even when the 12 V main switch is turned off. Therefore disconnect the living area battery from the 12 V power supply, if the vehicle will not be used for a long period of time.
9 Electrical system Fig. 138 Panel MP 20-T 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 9.9.
Electrical system Activating battery disconnection (transformer/rectifier without battery cut-off switch): Deactivating battery disconnection (transformer/rectifier without battery cut-off switch): 9.9.3 9 Switch off 12 V power supply. Press button for living area battery (Fig. 138,14) and hold it down for approx. 10 seconds. The "V" volt (Fig. 138,2) and "A" ampere (Fig. 138,3) symbols flash three times. The living area battery is disconnected from the 12 V power supply.
9 Electrical system Danger of total discharge (battery alarm) Battery voltage (values during operation) Mobile operation (vehicle moving, no 240 V connection) Battery operation (vehicle stationary, no 240 V connection) Power operation (vehicle stationary, 240 V connection) 11 V or less 1) 12 V power supply overload If appliances are switched off: Battery flat 12 V power supply overload The battery is not charged by the alternator, the alternator's regulator is defective 11.
9 Electrical system 9.9.4 Current displayed System status "A" ampere symbol -30 A to -10 A Battery is being heavily discharged Lights up red -10 A to -1 A Battery is being discharged Lights up white 0A Battery current is low or 0A Lights up white +1 A to +10 A Battery being charged Lights up white Tank gauge The water and waste water quantities can be indicated using the tank gauge. Displays: Press tanks button " " (Fig. 138,13). The water tank " " (Fig.
9 Electrical system Measures: 9.9.6 If, when the fill levels are called up, the LEDs in the scale flash in addition to the tank symbol, a sensor error has occurred. Clean tank sensors. Fill water tank or empty waste water tank. Temperature display The internal and external temperatures can be indicated using the digital display (Fig. 138,5). Displays: 9.9.7 Press internal temperature button " ature is displayed. " (Fig. 138,4).
Electrical system 9 The electrical appliances connected to the 12 V power supply of the living area are supplied with voltage by the living area battery. Connect the vehicle to an external 240 V power supply system as often as possible. The charger module in the transformer/rectifier automatically charges the living area battery. In addition to this, the starter battery is charged with a float charge. 9.10.
9 Electrical system Fig. 139 Connection possibilities 240 V connection Fig. 140 Connecting an angled connector with socket Adapter cable: CEE 17 socket with earth contact (Fig. 139,1) – plug with earth contact (Fig. 139,2) Cable reel: Socket with earth contact (Fig. 139,3) – plug with earth contact (Fig. 139,4) Adapter cable: CEE 17 socket with earth contact (Fig. 139,5) – plug with earth contact (Fig. 139,6) When using a CEE 17 angled connector with rear socket (Fig.
Electrical system 1 2 9 Unbroken fuse element Broken fuse element Fig. 141 12 V fuse An intact 12 V fuse can be detected by the unbroken fuse element (Fig. 141,1). If the fuse element is broken (Fig. 141,2), change the fuse. Before changing fuses, take the function, value and colour of the relevant fuses from the following specifications. When changing fuses, only use flat fuses with the values shown below.
9 Electrical system For vehicles on a Renault chassis, the fuses are installed near the starter battery under a covering between the seats. 1 2 3 Flat fuse 2 A/grey (for alternator D+) Jumbo flat fuse 40 A/orange Flat fuse 20 A/yellow (for charging line) Fig.
Electrical system 9 For vehicles built on a Renault chassis, the fuses are installed near the living area battery. 1 2 3 Jumbo flat fuse 20 A/yellow (for the refrigerator) Jumbo flat fuse 40 A/orange (for living area battery) Flat fuse 2 A/grey (for battery charger sensor) Fig. 147 Fuses on the living area battery (Renault) Fuse for the Thetford toilet (swivel toilet) The fuse is located in the locker wall of the Thetford cassette. Fig.
9 Electrical system Fuse for the Dometic toilet The fuse is located on the rear side of the control unit for the toilet. 1 2 Control unit Flat fuse 7.5 A/brown Fig. 151 Fuse for toilet Changing: 9.11.2 Lift the control unit for the toilet (Fig. 151,1) with a suitable tool and pull it from the wall. Replace fuse (Fig. 151,2). 240 V fuse Fig. 152 240 V automatic circuit breaker The 240 V connection is protected by one or several two-pole automatic circuit breakers (Fig. 152).
Appliances 10 Chapter overview 10Appliances This chapter contains instructions regarding the appliances of the vehicle. The instructions refer exclusively to the operation of the appliances. Further information about the appliances can be found in the instruction manuals for the appliances, included separately with the vehicle. The instructions address the following topics: 10.
10 Appliances 10.2 Heater Initial start-up 10.2.1 Never run the heater in gas operation when refuelling, on ferries or in the garage. Danger of explosion! Never operate the heater in gas operation in closed spaces (e.g. garages). Danger of poisoning and suffocation! When lighting the heater for the first time a small amount of smoke and odour will occur. Immediately set the operating switch of the heater to its highest position. Open doors and windows and ventilate well.
Appliances 10.2.3 10 Truma Combi hot-air heater When there is a danger of frost the heater is not in operation, empty the heating system. Do not use the space above and behind the heater as a storage compartment. The circulation fan is automatically switched on when the hot-air heater is activated, and it stays on. This puts an immense strain on the living area battery, if the vehicle is connected to an external 240 V power supply.
10 Appliances Green indicator lamp (Fig. 155,7) is on. The circulation fan automatically switches on when the heater is activated. Switching off: Turn the rotary switch (Fig. 155,3) to " " (Fig. 155,4). Close the gas isolator tap "Heater/boiler" and the regulator tap on the gas bottle. After switching off the heater, the circulation fan may still run for a moment to use up the residual heat.
Appliances 10.2.4 10 Trumatic C hot-air heater When there is a danger of frost the heater is not in operation, empty the heating system. Do not use the space above and behind the heater as a storage compartment. The circulation fan is automatically switched on when the hot-air heater is activated, and it stays on. This puts an immense strain on the living area battery, if the vehicle is connected to an external 240 V power supply.
10 Appliances Green indicator lamp (Fig. 157,7) is on. The circulation fan automatically switches on when the heater is activated. Switching off: Set the rotary switch (Fig. 157,3) to " " (Fig. 157,4). Close the gas isolator tap "Heater/boiler" and the regulator tap on the gas bottle. After switching off the heater, the circulation fan may still run for a moment to use up the residual heat.
Appliances 10.2.5 10 Webasto Dual Top hot-air heater Take the device out of operation by removing the fuse and contact customer service if one of the following events occurs: Long lasting, strong development of smoke; unusual combustion noises; smell of fuel; continuous fault shut-down with error message (blink code). The heater is powered with diesel fuel from the fuel tank of the base vehicle. The heater is not approved for operation with fuels of classes EL, L and PME (biodiesel).
10 Appliances Switching on the heater: Only select the "Heater and boiler" operating mode when the boiler is full of water. Set control knob "Temperature" (Fig. 159,6) on the operating unit to the desired thermostat setting for the room temperature. Set rotary switch "Operating mode" (Fig. 159,8) to winter operation "Heater without boiler" (Fig. 159,2) or to winter operation "Heater and boiler" (Fig. 159,4). The indicator lamp "Operation/fault" (Fig. 159,5) lights up green.
Appliances 1 2 3 4 5 6 7 8 9 10 10 LCD display "Back" button "Activate/Increase" button "Forward" button "Switch off/Decrease" button "System reset" button Lower menu line Information line Status line Upper menu line Fig. 160 Operating unit for hot-water heater Control buttons When no button is pressed, the operating unit automatically switches to home position after two minutes. The control buttons have the following functions: Pos. in Fig.
10 Appliances Fig. 161 LCD displays Pos. in Fig. 161 Upper menu line Status line On The heater is activated 2 Off The heater is switched off 3 Selection: Setting the desired temperature 4 Selection: Temporarily increasing (approx.
Appliances Pos. in Fig.
10 Appliances Switching on the heater: Switching the heater off: Alde heat exchanger Press the " " button (Fig. 160,4). The "Off" symbol (Fig. 161,2) flashes. Press the "+/On" button (Fig. 160,3). The "On" symbol (Fig. 161,1) flashes. The heater starts automatically. Press the " " button (Fig. 160,2). The operation ends, the display moves to home position and the "On" symbol lights up. Press the " " button (Fig. 160,4). The "On" symbol (Fig. 161,1) flashes.
Appliances Alde auxiliary circulating pump 10 The auxiliary circulating pump works only if a heat exchanger has been installed and the hot-water heater is running. Fig. 163 Auxiliary circulating pump Fig. 164 Operating switch for auxiliary circulating pump The auxiliary circulating pump (Fig. 163,1) can be used to heat the vehicle engine when parked. The auxiliary circulating pump is connected to the vehicle engine's cooling circuit and thus functions as an engine heater.
10 Appliances 240 V circulating pump Depending on the equipment, the hot-water heater has an additional 240 V circulating pump. If the vehicle is connected to the 240 V power supply, then it is possible to switch to the higher output of the 240 V circulating pump. The switch for switching between the 12 V circulating pump and the 240 V circulating pump is located on the hot-water heater operating unit. Selecting the circulating pump: 10.2.7 Press the " " button (Fig.
Appliances 10.2.8 10 Independent vehicle heater Do not operate the independent vehicle heater in closed spaces. Danger of suffocation! Do not operate the independent vehicle heater at petrol stations. Danger of explosion! The inside and the engine can be heated with the independent vehicle heater. The heating of the engine can be switched off. The independent vehicle heater can be turned on and off manually or with a timer.
10 Appliances 10.2.9 Heater for waste water tank and waste water pipes (winter comfort package) In order to prevent waste water fittings freezing up, the waste water tank and the waste water pipes can be electrically heated separately. When the heater is turned on, temperature sensors monitor the temperature of the waste water tank and the waste water pipes. If the temperature falls below 5 °C, the heating elements are switched on and the waste water tank and waste water pipes are heated.
Appliances 10 Fig. 169 Regulator for electrical floor warming unit Switching on: Switching off: Connect the vehicle to the 240 V power supply (see section 9.10.1). Turn the control knob (Fig. 169,2) to the required heating level. Turn control knob (Fig. 169,2) to "0" position. After switching off, the floor remains warm for a while, due to residual heat. If the regulator is overloaded, the overload protection is actuated. The pin (Fig. 169,1) jumps out. Switching on overload protection: 10.
10 Appliances To execute the individual switching commands, always point the remote control in the direction of the ceiling unit. Operating modes The air conditioning unit has the following operating modes: Switching on: Switching off: Automatic Ventilation, manual Cooling, manual Heating, manual Press the ON/OFF button (Fig. 170,9). Press the "Mode" button (Fig. 170,11) as often as required until the required mode (Fig. 170,1, 2, 3 or 4) is indicated on the display (Fig. 170,20).
Appliances 10.3.2 10 Slide the sliding regulator forwards or backwards to the desired position. The side on which the sliding regulator is located is closed. Turn the knob tight in the clockwise direction. Truma The air conditioning unit only runs if the vehicle is connected to a 240 V power supply. The external 240 V power supply must be protected by a fuse of at least 3 A. It is otherwise not possible to operate the air conditioning unit properly. Fig. 172 Receiver Fig.
10 Appliances Timer The air conditioning unit can be switched on or off automatically from the current time up to 15 hours in advance with the integrated timer. Pre-programming up to a certain time is not possible. To program, switch on the air conditioning unit with the key (Fig. 173,7) on the remote control. Set the desired operating mode and room temperature with the keys (Fig. 173,8, 3 and 4). Use the key (Fig. 173,5) to select the desired function (Fig. 173,1): 10.
Appliances 10.4.1 Models with waste gas vent on the right-hand side of the vehicle 10.4.2 10 If the awning is put up and the boiler is running in gas operation, exhaust gases from the boiler can escape into the awning area. Danger of suffocation! Make sure the area is sufficiently ventilated. Truma Combi boiler 1 2 3 4 5 Summer operation water temperature 40 °C or 60 °C Rotary switch Winter operation "Heater and boiler" Red indicator lamp "Fault" Yellow indicator lamp "Boiler heatingup phase" Fig.
10 Appliances Fig. 175 Safety/drainage valve of the boiler Variant: Boiler with gas operation Winter operation Summer operation Switching on: The boiler is operated exclusively with gas. In the "heater and boiler" switch setting in winter operation, the boiler is already switched on. In summer operation the water can be heated up to 40 °C or 60 °C. Open the regulator tap on the gas bottle and the gas isolator tap "Heater/ boiler". Set the rotary switch (Fig. 174,2) on the operating unit (Fig.
Appliances 1 2 3 4 5 6 10 240 V electrical operation (1800 W) 240 V electrical operation (900 W) Gas operation Gas and 240 V electrical operation (900 W) Gas and 240 V electrical operation (1800 W) Yellow indicator lamp "240 V electrical operation" Fig. 176 Energy selector switch for heater/boiler The boiler can be operated with different types of energy: Gas operation (Fig. 176,3) 240 V electrical operation with the output levels 900 W (Fig. 176,2) or 1800 W (Fig.
10 Appliances 10.4.3 Trumatic C boiler 1 2 3 4 5 Summer operation water temperature 40 °C or 60 °C Rotary switch Winter operation "Heater and boiler" Red indicator lamp "Fault" Yellow indicator lamp "Boiler heatingup phase" Fig. 177 Operating unit for heater/boiler The boiler is integrated into the heater and is operated with gas (gas operation) or with gas and/or electricity (gas and 240 V electrical operation). The boiler is switched on by turning the rotary switch (Fig.
Appliances 10 Fig. 178 Safety/drainage valve of the boiler Variant: Boiler with gas operation Winter operation Summer operation Switching on: The boiler is operated exclusively with gas. In the "heater and boiler" switch setting in winter operation, the boiler is already switched on. In summer operation the water can be heated up to 40 °C or 60 °C. Open the regulator tap on the gas bottle and the gas isolator tap "Heater/ boiler". Set the rotary switch (Fig. 177,2) on the operating unit (Fig.
10 Appliances 1 2 3 4 5 6 240 V electrical operation (1800 W) 240 V electrical operation (900 W) Gas operation Gas and 240 V electrical operation (900 W) Gas and 240 V electrical operation (1800 W) Yellow indicator lamp "240 V electrical operation" Fig. 179 Energy selector switch for heater/boiler The boiler can be operated with different types of energy: Gas operation (Fig. 179,3) 240 V electrical operation with the output levels 900 W (Fig. 179,2) or 1800 W (Fig.
Appliances 10.4.4 10 Webasto Dual Top boiler Take the device out of operation by removing the fuse and contact customer service if one of the following events occurs: Long lasting, strong development of smoke; unusual combustion noises; smell of fuel; continuous fault shut-down with error message (blink code).
10 Appliances Switching the boiler on: Set the rotary switch "Operating mode" (Fig. 180,8) to summer operation "40 °C" or "70 °C" (Fig. 180,1) or to winter operation "Heater and boiler" (Fig. 180,4). The indicator lamp "Operation/fault" (Fig. 180,5) lights up green. The symbol of the selected operating mode lights red. Switching the boiler off: Turn the rotary switch "Operating mode" (Fig. 180,8) to "OFF" (Fig. 180,10). The indicator lamp "Operation/fault" (Fig. 180,5) goes off.
Appliances 10.4.5 Switching the boiler on/off Filling/emptying the boiler 10 Alde boiler The boiler is integrated in the hot-water heater. A separate operation is not possible. For operating the hot-water heater, see section 10.2.6. The boiler can be supplied with water from the water tank. Fig. 181 Drain cock Filling the boiler with water: Emptying the boiler: 10.5 EN Switch on 12 V power supply on the panel. Set all the water taps to "Hot" and open them.
10 Appliances 10.5.1 Gas cooker During activation and operation of the gas cooker, no flammable objects or highly inflammable objects such as dishcloths, napkins etc. must be near the gas cooker. Fire hazard! The process of ignition must be visible from above and must not be covered by cooking pans placed on the cooker. Depending on the model, the gas cooker lid is held closed by a spring.
Appliances Switching off: 10.5.2 10 Release the control knob and turn to the desired setting. If ignition is unsuccessful, repeat the entire procedure. Turn the control knob to the 0-position. The flame fades. Close the gas isolator tap "Cooker" and the regulator tap on the gas bottle. Gas oven (Spinflo) Keep the ventilation openings on the gas oven open at all times. There must be no flammable objects near the gas oven when it is being lit.
10 Appliances Switching off: 10.5.3 Turn control knob (Fig. 184,2) to " ". The flame fades. Close the gas isolator tap "Oven" and the regulator tap on the gas bottle. Gas oven (Dometic) Keep the ventilation openings on the gas oven open at all times. There must be no flammable objects near the gas oven when it is being lit. If ignition has not taken place, repeat the entire procedure. If necessary, check if there is gas and/or current in the gas oven.
Appliances 10.5.4 10 Microwave oven Only qualified personnel may repair the microwave oven. Improper repairs can cause major risks to the user. The protection device against the escape of microwave energy should never be removed. Use the microwave oven only if it has been properly installed. Only use the microwave oven when the door seal is free of damage. Never leave the microwave oven unattended when it is in operation.
10 Appliances 10.5.5 Extractor hood Fig. 187 Extractor hood The cooking area is equipped with an extractor hood. The two-level fan blows the cooking steam directly outside. 10.6 Use the switch (Fig. 187,1) to turn the extractor hood on and off. Use the switch (Fig. 187,2) to turn the cooker lamps on and off. Refrigerator During the journey, only operate the refrigerator via the 12 V power supply. At high ambient temperatures the refrigerator is unable to reach its full cooling power.
Appliances 10 Thetford Fig. 190 Refrigerator ventilation grill (Thetford) Removal: 10.6.2 Operating modes Move the locking device (Fig. 190,1) to the middle. Remove refrigerator ventilation grill. Operation (Dometic 7 series, automatic ignition) The refrigerator has 2 operating modes: Gas operation Electrical operation (240 V AC or 12 V DC) The operating mode is set with the operating controls on the refrigerator panel. Gas operation Select only one energy source.
10 Appliances Switching off: Electrical operation Set the control knob (Fig. 191,5) to maximum power. Gas supply is open. Ignition will take place automatically. A ticking sound can be heard until ignition has been completed successfully. The "GAS" operating indicator (Fig. 191,3) lights up yellow. Adjust the refrigerating temperature with the control knob. Set energy selector switch to " ". Refrigerator is switched off.
Appliances 10 12 V DC Gas Choosing the available energy source highest on the list. Even when the 12 V power supply is switched off, a small electrical power flows which puts an extra load on the living area battery. Always switch off the refrigerator for a temporary lay-up. 1 2 3 4 5 6 Frame heater (FH) button Indicator lamp Energy selector switch Indicator lamps Indicator lamps Control knob for setting the temperature Fig.
10 Appliances When changing over between the different power sources there are forced delays built in the AES. This means, that after a change-over to a new energy source the refrigerator can not be operated immediately. When changing over from 12 V operation to gas operation, a 15-minute delay is built in the AES. This prevents a change-over to gas operation when the vehicle is stopped briefly and the engine is switched off (e.g. stop to fill tank).
Appliances 10.6.4 Operating modes 10 Operation (Dometic 8 series) The refrigerator has 2 operating modes: Gas operation Electrical operation (240 V AC or 12 V DC) The operating mode is set with the operating controls on the refrigerator panel. Gas operation Select only one energy source. Never let gas escape unburned due to danger of explosion. It is not permitted to operate the refrigerator with car gas.
10 Appliances The refrigerator can be operated with the following voltages: Switching the 240 V operation on: Switching the 240 V operation off: Switching the 12 V operation on: Switching the 12 V operation off: Operating modes Set the energy selector switch (Fig. 193,2) to " ". Use the control knob (Fig. 193,3) to adjust the refrigerating temperature. Set energy selector switch to " ". Refrigerator is switched off. Set the energy selector switch (Fig. 193,2) to " ".
Appliances 10 Fig. 194 Operating controls for the refrigerator (Dometic 8 series with MES) 1 2 3 4 5 6 7 Switching on: On/off switch/energy selector switch Display-LED "open door" (only for central locking system of the refrigerator door) Display-LED "fault" Operating indicators Display-LED "temperature range" Switch for temperature setting Door opener (only for refrigerator door central locking system) Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator".
10 Appliances Switching the 12 V operation on: Switching the 12 V operation off: Press the on/off switch/energy selector switch (Fig. 194,1) down for 2 seconds in order to switch on the appliance. The LED of the operating mode chosen most recently lights up. If appropriate press the on/off switch/energy selector switch (Fig. 194,1) several times until the operating indicator 12 V " " lights up. Use switch (Fig. 194,6) to adjust refrigerating temperature.
Appliances 10 Even when the 12 V power supply is switched off, a small electrical power flows which puts an extra load on the living area battery. Always switch off the refrigerator for a temporary lay-up. 240 V operation If the 240 V power supply is connected, this energy source is selected as the first priority by the AES. 12 V operation 12 V operation is only selected by the AES if the vehicle's engine is running and the alternator supplies sufficient 12 V operating power.
10 Appliances Manual operation Switching on: Switching off: 10.6.7 Press the on/off switch/energy selector switch (Fig. 195,1) down for 2 seconds in order to switch on the appliance. The operating mode selected most recently is shown in the operating indicator (Fig. 195,4). Select the energy type with the on/off switch/energy selector switch (Fig. 195,1). Set the refrigerating temperature on the switch for temperature setting (Fig. 195,6). The indicator LEDs (Fig.
Appliances Gas operation 10 Never let gas escape unburned due to danger of explosion. It is not permitted to operate the refrigerator with car gas. 1 2 3 4 Button for thermostat On/Off button Display Button for operating mode Fig. 196 Operating controls for the refrigerator (Thetford without SES) Switching on: Switching off: Electrical operation Open the regulator tap on the gas bottle and the gas isolator tap "Refrigerator". Press the button (Fig. 196,2). The display (Fig.
10 Appliances Switching the 240 V operation off: Switching 12 V operation on: Switching 12 V operation off: Press the button (Fig. 196,2). The display is no longer lit up. Refrigerator is switched off. Press the button (Fig. 196,2). Press the button (Fig. 196,4) repeatedly until the 12 V operating mode " appears on the display. " Press the button (Fig. 196,1) repeatedly until the desired thermostat setting appears on the display. Press the button (Fig. 196,2).
10 Appliances Dometic 7 series Fig. 197 Locking of the refrigerator door (Dometic 7 series) Opening: Closing: Locking in the ventilation position: Push the lock (Fig. 197,1) to the left " Fig. 198 Refrigerator door in ventilation position (Dometic 7 series) ". Use recessed grip to open refrigerator door. Fully close the refrigerator door. Push the lock (Fig. 197,1) completely to the right " ". Slightly open refrigerator door. Push the lock completely to the right.
10 Appliances Locking in the ventilation position: Slightly open refrigerator door/freezer compartment door. Push the lock completely to the right. The door latch (Fig. 200,1) keeps the refrigerator door/freezer compartment door in a fixed position. The refrigerator door/freezer compartment door will then stay slightly open (Fig. 200). Dometic 8 series Fig. 201 Release button of the refrigerator door (Dometic 8 series) Fig. 202 Lock hook fixture Opening: Press the release button (Fig.
Appliances 10 Thetford Fig. 205 Lock of refrigerator door, closed (Thetford) Opening: Closing: Locking in the ventilation position: Motorcaravan - 09-08 - DET-0033-07 EN Fig. 206 Refrigerator door in ventilation position (Thetford) Open the refrigerator door at the handle (Fig. 205,2). The lock (Fig. 205,1) is released automatically. Fully close the refrigerator door. Ensure that the lock is engaged. Slightly open refrigerator door/freezer compartment door.
10 188 Appliances Motorcaravan - 09-08 - DET-0033-07 EN
Sanitary fittings Chapter overview 11 11Sanitary fittings This chapter contains instructions regarding the sanitary fittings of the vehicle. The instructions address the following topics: 11.1 water tank waste water tank complete water system toilet compartment toilet Water supply, general Fill the water tank with fresh water only. Water left standing in the water tank or in the water pipes becomes undrinkable after a short period.
11 Sanitary fittings 11.2 Switch for water pump (winter comfort package) Fig. 208 Switch for water pump The switch for the water pump (Fig. 208,1) is installed in the water tank area. The water pump can be switched off with this switch. This prevents the water pump from starting if the water system is empty and the water taps are opened. Otherwise, the water pump will run hot and discharge the living area battery. 11.3 11.3.
Sanitary fittings 11.3.2 Models with a double floor 11 Remove the key. Check that the cap sits firmly on the fresh water filler neck. Water drainage A hose line can be connected to the water drain neck under the floor of the vehicle. Fig. 211 Drain cock in the double floor The drain cock (Fig. 211,1) is fixed in the double floor. The drain cock is labelled by the word "Wasser" (water). Models without double floor All models without double floor have no drain cock.
11 Sanitary fittings 11.3.4 Models with double floor Draining water To empty the water tank, proceed as follows: Fig. 214 Water drain neck and waste water drain neck Models without double floor Mount suitable hose to the water drain neck (Fig. 214,1) or place appropriate container under the water drain neck. Open drain cock (Fig. 211,1). The water will drain. Close the drain cock. Close the external flap.
Sanitary fittings 11.4.1 11 Waste water tank (models with double floor) With the models with a double floor, the waste water tank is heated by the hot air of the living area heater. This protects the waste water tank from frost when the living area heater is in operation. Fig. 215 Waste water tap Fig. 216 Waste water drain neck Depending on the model, the waste water tap for waste water disposal is located on the left or right hand side of the vehicle. The waste water tap (Fig.
11 Sanitary fittings Emptying: 11.4.3 Place key (Fig. 217,2) onto the square bolt (Fig. 217,1). In order to open the waste water tap, turn the square bolt a quarter turn. Completely empty waste water tank. To close the waste water tap, turn the square bolt back as far as it will go. Odour seal For models without double floor, remove the siphon base if there is a risk of frost. This protects the siphon from freezing up.
Sanitary fittings 11.5 11 Filling the water system When filling the water tank, observe the maximum permissible gross weight of the vehicle. Luggage must be reduced accordingly when the water tank is full. The water pump will overheat without water and can get damaged. Never operate water pump when the water tank is empty. The Truma system (heater/boiler) has an electric safety/drainage valve and, depending on the model, one or two drain cocks for emptying.
11 Sanitary fittings 11.6 Set all water taps to "Cold" and leave them open. This will fill the cold water pipes with water. Keep the taps open until the water flowing out of the taps has no bubbles in it. Close all water taps. Check that the cap on the water tank is not leaking. Emptying the water system If the vehicle is not used for several days or if it is not heated when there is a risk of frost, empty the entire water system. Leave the water taps on in central position.
Sanitary fittings 11.7 11 For models with an double floor: Remove the cap from the waste water drain neck and open the drain cock. Open all water taps and set to the central position. Hang the shower handset up in the shower position. Hold the water pump up until the water pipes are completely empty. Check whether the water tank is completely empty. Blow out the remaining water in the water pipes (max. 0.5 bar).
11 Sanitary fittings 11.8 Toilet 11.8.1 If there is any risk of frost and the vehicle is not heated, empty the sewage tank (cassette). Do not sit on the lid of the toilet. The lid is not designed to bear the weight of a person and could break. Use a suitable chemical for this toilet. The ventilation will merely remove the odour but not germs and gases. Germs and gases will have a detrimental effect on the sealing rubbers.
Sanitary fittings Fig. 224 Thetford toilet bowl, swivelling 11 Fig. 225 Thetford toilet bowl, swivelling (alternative) The operating unit is located close to the toilet bowl. Fig. 226 Flush button/indicator lamp Thetford toilet Flushing: Fig. 227 Flush button/indicator lamp Thetford toilet (alternative) Before flushing open the sliding trap of the Thetford toilet. To do this, push the slide lever (Fig. 224,1 or Fig. 225,1) in an anticlockwise direction.
11 Sanitary fittings Fig. 228 Operating unit Thetford toilet Flushing: Before flushing open the sliding trap of the Thetford toilet. To do this, turn the slide lever (Fig. 228,1) in an anticlockwise direction. For flushing, press the blue flush button (Fig. 228,3). After flushing close the sliding trap. To do this turn the slide lever (Fig. 228,1) in a clockwise direction. The indicator lamp (Fig. 228,2) goes on whenever the Thetford cassette has to be emptied. Emptying: 11.8.
Sanitary fittings Fig. 230 Toilet bowl with control and operating unit 11 Fig. 231 Control and operating unit toilet Let some water run into the toilet bowl before using the toilet. In order to do so press the flush button (Fig. 231,3) on the control and operating unit (Fig. 230,2). Flushing: Before flushing open the sliding trap of the toilet. For this pull out the slide lever (Fig. 230,1). For flushing, press the flush button (Fig. 231,3). After flushing close the sliding trap.
11 Sanitary fittings Fig. 232 Vacuum toilet Putting into operation: Fig. 233 Vacuum toilet panel Turn on power supply. The yellow LED (Fig. 233,1) on the panel (Fig. 232,1) turns on for ca. 1 minute. A vacuum is generated in the system. If the green LED (Fig. 233,3) on the panel lights up, lift the pedal (Fig. 232,3) briefly, so that some water runs into the toilet bowl (Fig. 232,2) and the stopper on the bottom is covered with water. The vacuum toilet is ready for operation.
Sanitary fittings 11.8.6 11 Press both push-button locks (Fig. 234,2) simultaneously with your thumb and open the flap for the cassette. Press the release (Fig. 235,1) and pull out the toilet cassette on the handle (Fig. 235,2). Emptying the cassette Fig. 236 Emptying the Thetford cassette 11.9 Take the cassette to a disposal point especially provided for this purpose. As you do this, point the drainage neck upwards. If necessary, turn the drainage neck upwards.
11 Sanitary fittings 11.9.1 Converting into a shower cubicle Fig. 237 Vario toilet, locking the shower wall Fig. 238 Vario toilet Push the latch (Fig. 237,1) right on the edge of the wash basin and lightly pull the wash basin. The wash basin moves forwards with the rear wall. Turn the wash basin and the rear wall (Fig. 238,1) in the direction indicated. Enter the toilet compartment and close the toilet door (Fig. 238,2) from the inside and lock. Fig.
Care 12 Chapter overview 12Care This chapter contains instructions regarding the care of the vehicle. The instructions address the following topics: exterior of the vehicle interior extractor hood toilets winter operation At the end of the chapter there is a checklist of measures you must carry out if you are not going to use the vehicle for an extended period of time. The checklist address the following topics: 12.1 12.1.
12 Care 12.1.3 Add-on parts made of glass-fibre reinforced plastic (GRP) require a regular follow-up treatment with a polisher. This way these parts will not turn yellow and the sealing of the surface remains intact. Treat rubber seals of doors and storage flaps with talc. Treat locking cylinder of doors and storage flaps with graphite dust. Windows of acrylic glass Acrylic glass windows are delicate and require very careful handling. 12.1.
Care 12.1.7 12 Driver's cabin insulation mat (model I) Clean the insulation mat for the driver's cabin with clear, lukewarm water. Remove heavier soiling with a cloth and some white spirits. Afterwards, immediately rinse the cleaned area with lukewarm water. 12.2 Interior care Motorcaravan - 09-08 - DET-0033-07 EN If possible, treat stains immediately. Acrylic glass windows are delicate and require very careful handling (see section 12.1.3).
12 Care 12.3 Clean PVC-floor covering with a mild, soapy cleanser for PVC floors. Do not place carpet on wet PVC-floor covering. The carpet and the PVC-floor covering may stick together. Never clean the sink or the gas cooker with a scourer. Avoid anything which may cause scratching or grooves. Clean gas cooker only with a moist cloth. Prevent any water from penetrating the gas cooker. Water may damage the gas cooker.
Care 12.4.1 12 Toilet with separate water tank Fig. 241 Toilet water tank drain hose Emptying the tank: 12.4.2 Press the flush button, to active the operating panel. Open the sliding trap and flush until no more water flows. Close the sliding trap. Empty the cassette (Fig. 241,2) at a disposal station authorized for this purpose and clean it. Leave the drainage neck (Fig. 241,3) open. Remove the drain hose (Fig. 241,5) from the holder (Fig. 241,4).
12 Care 12.5 Press the pedal several times until water no longer comes out of the valve. Screw the cap back on and attach cover. Winter care De-icing salt damages the underbody and the parts open to water spray. We recommend that you wash the vehicle more frequently during wintertime. Mechanical and surface treated parts and the underside are under particular strain, and should therefore be cleaned thoroughly. 12.5.
Care 12.6 12.6.1 12 Lay-up Temporary lay-up If the vehicle has been stationary for a long period (approx. 10 months) have the braking and gas systems checked by an authorised specialist workshop. Take into consideration that water is undrinkable after only a short time. Animal damage to cables can lead to short circuits. Fire hazard! Animals (especially mice) can cause great damage to the interior of the vehicle. This is especially true if the animal remains undisturbed in a parked vehicle.
12 Care Activities Done Search for traces of animals that have gained entry Disconnect the flat screen from the mains and, if necessary, remove it from the vehicle Gas system Close regulator tap on the gas bottle Close all gas isolator taps Always remove gas bottles from the gas bottle compartment, even if they are empty Electrical system Fully charge living area and starter battery Charge the battery for at least 20 hours before laying up.
Care Activities 12 Done Thoroughly clean the interior If there is a risk of frost, do not leave the flat screen in the vehicle Electrical system Remove starter and living area batteries and store in a place protected from frost (see chapter 9) Water system Clean the water system using a cleaning agent from a specialised store Complete vehicle Arrange the tarpaulins in such a way that the ventilation openings are not covered, or use porous tarpaulins 12.6.
12 Care Activities Water system Done Use several litres of fresh water to rinse out water pipes and water tank.
Maintenance Chapter overview 13 13Maintenance This chapter contains instructions about inspection and maintenance work concerning the vehicle. The maintenance instructions address the following topics: Alde hot-water heater independent vehicle heater air conditioning unit replacing bulbs and fluorescent tubes AL-KO rear axle At the end of the chapter you will find important instructions on how to obtain spare parts. 13.
13 Maintenance 13.3.1 Have heating fluid changed by an authorised dealer or a service centre at intervals of approximately two years as corrosion-protection wears off after some time. Top up heating system with a water-glycol mixture (60 : 40) only. This mixture offers frost protection up to approx. -25 °C. When topping up hot-water heaters that are connected to the engine's cooling circuit, please observe the instructions in the instruction manuals of the manufacturers.
Maintenance 13.3.3 13 Bleeding the heating system Fig. 244 Bleeding valve of hot-water heater The bleeding valves are built in nearby the radiators. 13.4 Switch off the hot-water heater and allow it to cool down. Open bleeding valve (Fig. 244,1) and leave open until no more air escapes. Close bleeding valve. Repeat this procedure at all bleeding valves. Check to see if the hot-water heater warms up.
13 Maintenance 13.5.1 Truma Fig. 245 Air conditioning unit (Truma) A lint filter (Fig. 245,1) for the air circulation suction system is at the front of the air conditioning unit. The lint filter must be cleaned at regular intervals, at least twice a year however, and replaced if necessary. The condensation drain is under the floor of the vehicle. Keep the drain hose free from dirt, leaves or similar to allow the condensation to be drained. 13.5.2 Dometic Fig.
Maintenance 13.6.1 13 Do not use any bulb that has been dropped or which shows scratches in its glass. The bulb might burst. Lights can get very hot. When the light is switched on, there must always be a safety distance of 30 cm between light and flammable objects. Fire hazard! A new bulb should not be touched with the fingers. Use a cloth when installing the new bulb. Only use bulbs of the same type and with the correct wattage.
13 Maintenance 13.6.3 Halogen spotlight (with glass shade) Fig. 249 Halogen spotlight (with glass shade) Changing bulbs: 13.6.4 Pull the halogen bulb (Fig. 249,1) forward out of the socket. Press the new halogen bulb into the fitting between the two spring tongues. Halogen spotlight (movable) Fig. 250 Halogen spotlight (movable) Changing bulbs: 13.6.5 Loosen the fixing screws (Fig. 250,1). Carefully remove the lamp chalice (Fig. 250,2) from the holder. Remove halogen bulb.
Maintenance 13.6.6 13 Press the light covering (Fig. 251,3) lightly together and remove it. Remove the fluorescent tube. Insert a new fluorescent tube. Reassemble the lamp in the reverse order. Living area lamp Fig. 252 Living area lamp Changing bulbs: 13.6.7 Remove the screw (Fig. 252,1) and take off the cover (Fig. 252,2). Press the glass together gently and remove from the housing. Remove the fluorescent tube. Insert a new fluorescent tube.
13 Maintenance 13.6.8 Recessed halogen light (flat) Fig. 254 Recessed halogen light (flat) Fig. 255 Changing the halogen bulb The recessed halogen light (Fig. 254,1) is installed flush. Changing bulbs: 13.6.9 Use a screwdriver to remove the inner cover ring (Fig. 255,1) from the housing. Use a screwdriver to remove the cover ring with the glass (Fig. 255,2) from the lower section of the recessed halogen light. Remove halogen bulb (Fig. 255,3). Put in a new halogen bulb.
Maintenance 13.6.10 13 Wardrobe light Fig. 257 Wardrobe light Changing bulbs: 13.7 Press the light covering (Fig. 257,1) lightly together and remove it. Remove halogen bulb. Put in a new halogen bulb. Reassemble the lamp in the reverse order. Changing the battery of the wardrobe light with LED The wardrobe light has a button cell that supplies voltage to the LED. Use only button cells of the same type. Fig.
13 Maintenance The rear axles must not bear any load while they are being lubricated. Use one of the following types of grease for lubrication: Costrac GL 1501 by the firm Klüber Cardex 3746 SP by the firm CONDA If the vehicle is equipped with a maintenance-free torsion bar spring axle or a rear axle with pneumatic cushioning, the two lubricator nipples are left out. Fig. 259 AL-KO rear axle The lubricator nipples (Fig. 259, arrow) are situated on the underside of the axle tube. 13.
Maintenance 13 When ordering spare parts please indicate the serial number and the vehicle type to the Dethleffs dealer. The vehicle described in this instruction manual is built and equipped to factory standards. Special equipment is offered depending on its purpose or use. When fitting special equipment check if such equipment has to be entered in the vehicle documents. Observe the max. permissible gross weight. Your Dethleffs dealer will be pleased to advise you. 13.
13 Maintenance 226 Replacement stickers can be obtained from an authorised dealer or a service centre.
Wheels and tyres Chapter overview 14 14Wheels and tyres This chapter contains instructions regarding the tyres of the vehicle. The instructions address the following topics: tyre selection handling of tyres changing wheels spare wheel support tyre pressure At the end of the chapter there is a table you can use to find the correct tyre pressure for your vehicle. 14.1 General Check tyre pressure before a journey or every 2 weeks.
14 Wheels and tyres Fig. 262 Tighten the wheel nuts or wheel bolts cross-wise 14.2 Check regularly that the wheel nuts or wheel bolts are firmly seated. Retighten the wheel nuts or wheel bolts of a changed wheel cross-wise (Fig. 262) after 50 km (30 miles). When using new or newly painted rims, re-tighten the wheel nuts or wheel bolts once again after approx. 1,000 to 5,000 km (600 miles to 3,000 miles).
Wheels and tyres 14.3 215/70 R 15C 109/107 Q 14.4 Tyre specifications Description Explanation 215 Tyre width in mm 70 Height-to-width proportion in percent R Tyre design (R = radial) 15 Rim diameter in inches C Commercial (transporter) 109 Load index code for single tyres 107 Load index code for twin tyres Q Speed index (Q = 160 km/h) Handling of tyres 14.5 EN Drive over kerbs at an obtuse angle. Otherwise the flanks of the tyres may get pinched.
14 Wheels and tyres 14.6 Use the vehicle jack only for lifting the vehicle briefly while changing the tyre. Do not start the motor while the vehicle is jacked up. Whilst the vehicle is in a jacked up position, persons must not lie down under it. Do not damage the thread of the thread bolts when changing the wheel. Tighten the wheel nuts or wheel bolts cross-wise (Fig. 262). When changing wheels (e.g.
Wheels and tyres 14 Fig. 263 Spare wheel support under the vehicle Removing the spare wheel: 14.7 Use the ratchet wrench and extension to loosen the nuts (Fig. 263,1) on the rear hooks (Fig. 263,2) to the left and right of the spare wheel support. Unscrew the wheel nuts approx. 3 to 4 cm. Press the clip (Fig. 263,3) slightly upwards, press the hooks backward or forward and unhook the clip. Take down the basket and remove the spare wheel.
14 Wheels and tyres Fiat Renault Ford Types Tyre size Front air pressure in bar Rear air pressure in bar All types 215/70 R 15 C (109/107) Q 4.1 4.5 All types with "Michelin Camping" tyres 215/70 R 15 C (109/107) Q 5.0 5.5 All types 225/75 R 16 C (116/114) R 4.5 5.0 All types with "Michelin Camping" tyres 225/75 R 16 C (116/114) R 5.5 5.5 All types 225/75 R 16 C (116/114) Q (tandem axle) 4.5 3.5 All types with "Michelin Camping" tyres 225/75 R 16 C (116/114) Q (tandem axle) 5.
Troubleshooting Chapter overview 15 15Troubleshooting This chapter contains instructions about possible faults in your vehicle. The faults are listed with their possible causes and corresponding remedies.
15 Troubleshooting Fault Cause Remedy No 240 V power supply despite connection 240 V automatic circuit breaker has triggered Switch on the 240 V automatic circuit breaker Starter or living area battery is not charged when operated in 240 V mode Jumbo flat fuse (40 A) on the starter or living area battery is defective Replace jumbo flat fuse (40 A) on the starter or living area battery Charger module in the transformer/rectifier is defective Contact customer service Living area battery is not ch
Troubleshooting 15 Fault Cause Remedy 12 V power supply does not work in 240 V operation 12 V power supply switched off Switch 12 V power supply on Living area battery disconnected from the 12 V power supply Connect the living area battery with the 12 V power supply Charger module in the transformer/rectifier is defective Contact customer service 240 V automatic circuit breaker has triggered Contact customer service Jumbo flat fuse (40 A) on the living area battery is defective Replace jumbo
15 Troubleshooting 15.3 Gas system 15.4 15.4.1 15.4.2 If the gas system is defective: Do not smoke; do not ignite any open flames, and do not operate electric switches (light switches etc.). Have the defective gas system repaired by an authorised specialist workshop.
Troubleshooting 15.5 15 Fault Cause Remedy Microwave oven does not cut in Fuse is defective Replace fuse Door of the microwave oven is not properly closed Remove foreign bodies stuck in the door of the microwave oven and close door properly Heater/boiler In the event of a defect contact the nearest customer service workshop of the relevant appliance manufacturer. The list of addresses is enclosed with the accompanying appliance documentation.
15 Troubleshooting Fault Cause Remedy Boiler empties, safety/ drainage valve has opened Internal temperature below 8 °C Heat inside Safety/drainage valve separated from battery supply Cancel battery separation. In order to do this switch on the battery cutoff switch on the transformer/rectifier or deactivate the battery separation via the panel Operating voltage below 10.
Troubleshooting 15 Fault Cause Remedy Heating running, but no heat at the convectors Circulating pump does not work Switch on room thermostat Contact customer service Heating and circulating pump running, but no heat at the convectors 15.6 Air in the heating system Bleed hot-water heater Refrigerator In the event of a defect contact the nearest customer service workshop of the relevant appliance manufacturer. The list of addresses is enclosed with the accompanying appliance documentation.
15 Troubleshooting 15.6.
Troubleshooting 15.6.
15 Troubleshooting 15.6.4 Dometic 8 series with MES In the case of a fault the LED display fault will always light up " Fault LED " LED " LED " " flashes " flashes " flashes ".
15 Troubleshooting 15.6.5 Dometic 8 series with AES In the case of a fault the LED display fault will always light up " ".
15 Troubleshooting 15.7 15.7.
Troubleshooting 15.
15 Troubleshooting 15.9 15.
Special equipment 16.1 Weight details for special equipment 16 16Special equipment The use of accessories, parts and fittings not supplied by Dethleffs may cause damage to the vehicle and jeopardize road safety. Even if an expert's report, a general type approval or a design certification exists, there is no guarantee for the proper quality of the product. Every alteration of the original condition of the vehicle can alter road behaviour and jeopardize road safety.
16 248 Special equipment Item designation Surplus weight (kg) External gas socket 1 Holder for flat screen 3-5 Lift-tilt skylight (Heki 3) 22 Trumatic C 6002 heater, electric kit 1 Insect screen door 3 Insulation mat for driver's cabin window 2 Air conditioning unit 32-40 Driver's cabin air conditioning unit 30 Refrigerator, separate freezer compartment 20 Awning 300 cm 21 Awning 350 cm 25-35 Awning 400 cm 27-40 Awning 450 cm 32 Awning 500 cm 36 Awning 600 cm 40 Microwave
Special equipment Motorcaravan - 09-08 - DET-0033-07 EN 16 Item designation Surplus weight (kg) Additional heater, driver's cabin (independent vehicle heater) 7 Additional pump for the Alde heater 1 Auxiliary heat exchanger (Arizona) 3 249
16 250 Special equipment Motorcaravan - 09-08 - DET-0033-07 EN
Helpful notes 17 Chapter overview 17Helpful notes This chapter contains helpful tips for the journey. The instructions address the following topics: road assistance in European countries traffic rules in European countries gas supply in European countries toll regulations in European countries safe ways to spend the night during travel camping in winter At the end of the chapter there is a checklist containing the most important equipment for the journey. 17.
17 Helpful notes Country Greece Emergency services Police 112 171/112 Great Britain Ireland Breakdown service ELPA 104 00 1) 112 112 AA (08 00) 0 28 90 18/ (08 00) 82 82 82 1) 999/112 1) AA Dublin 18 00 66 77 88 999/112 1) Iceland 112 F.I.
Helpful notes Country Switzerland Emergency services Police 144 17 Breakdown service TCS 1 40/03 18 50 53 11 1) 117/112 1) Serbia 94 AMSS (011) 19800 92 Slovakia 155/112 1) SATC 1 81 24 158/112 1) Slovenia Spain 112 113 AMZS (1) 9 87/ (003861) 5 30 53 53 1) 061 RACE 9 15 93 33 33 112 Czech Republic 155/112 1) UAMK CR 12 30 158/112 1) Turkey 112 TTOK (02 12) 2 82 81 40 155/112 1) Ukraine 03 112 UA (8-032) 2 97 81 12 02 Hungary 104/112 1) 107/112 1) Cyprus 112 MAK 1 88/(0036-1)
17 Helpful notes Country Belgium Bulgaria Denmark Germany Estonia Width Lgth. 2.55 12 2.60 2.55 2.55 2.50 12 12 12 12 Finland 2.60 12 France 2.55 12 Gross weight In builtup areas Outside built-up areas Motorway Up to 7.5 t 50 120 Over 7.5 t 50 90/120 1) 60/90 1) Up to 3.5 t 50 90 130 Over 3.5 t 50 70 100 Up to 3.5 t 50 80 130 Over 3.5 t 50 70 80 Up to 3.5 t 50 100 130 3) 3.5 t up to 7.5 t 50 80 100 Over 7.5 t 2) 50 80 80 Up to 3.
Helpful notes Country Austria Poland Portugal Romania Russia Sweden Max. dimensions in meters Width Lgth. 2.55 12 2.50 2.50 2.50 2.50 2.60 Switzerland 2.55 Serbia and Montenegro 2.50 Slovakia 2.50 Slovenia 2.55 12 12 12 12 24 14) 12 12 12 12 17 In builtup areas Outside built-up areas Up to 3.5 t 50 100 Over 3.5 t 50 70 Up to 3.5 t 50 130 Over 3.5 t 50 90/100 1) 70/80 1) Up to 3.5 t 50 Over 3.5 t 50 90/100 11) 80/90 11) 120 12) 110 12) Up to 3.
17 Helpful notes 9) On main roads 2.55 m, on roads marked "B" 2.20 m 10 p.m. and 5 a.m. the speed limit on the following motorways is 100 km/h: A10 (Tauernautobahn), A12 (Inntalautobahn), A13 (Brennerautobahn), A14 (Rheintalautobahn) 10) Between 11) According to traffic signs Drivers who have had their driver's licence for less than one year must not drive faster than 90 km/h.
Helpful notes Country Conditions Slovenia All year; on all roads Czech Republic All year; on all roads Hungary All year; only outside of towns 17 Specifications without guarantee 17.5 Sleeping in the vehicle away from camping areas Country EN Sleeping on privately owned lands Yes Yes No Belgium X Bulgaria X Comments No X On highway rest areas max.
17 Helpful notes Country Sleeping on roads and fields Sleeping on privately owned lands Yes Yes No Comments No Norway X X Officially prohibited on rest areas and cultivated grounds. Travelling on dirt roads is prohibited Austria X X Staying overnight for one night to restore driving ability is permitted, but not in nature reserves. Observe regional and local restrictions.
Helpful notes 17.6 Gas supply in European countries General tips In Europe, there are several different connection systems for gas bottles. It is not always possible to fill or exchange your gas bottles in a foreign country. Get information about the connection system in the country you are travelling to before embarking on your journey, e.g. at a motoring club or in the trade press. Always observe the following instructions: 17.
17 Helpful notes 17.9 Only take with you those valuables which are absolutely necessary for the journey. If possible, store valuables in a small safe and not in the immediate vicinity of windows or doors. Always lock up the vehicle. Tips for winter campers The following tips will help make your winter camping experience as agreeable as possible. 260 Reserve your parking place in good time. Good winter camping sites are often booked up early.
Helpful notes 17.10 17 Travel checklists The following checklists will help that nothing important is left at home although not everything on the checklists might be necessary. Do not leave checking of documents (e.g. vehicle papers and information) as well as checking the condition of the vehicle until just before commencing the trip. Planning and checking documents well in advance will save unnecessary trouble.
17 Helpful notes Vehicle/tools Outside Documents 262 Object Object Object Binoculars Neck-supporting pillow Clothes pins Fire extinguisher Sewing kit Clothesline Gas bottle Radio Waste water container Fabric tape Screwdriver Adapter socket Watering can for fresh water Current-measuring instrument CEE adapter Cable reel Step Wire V-belt Wheel chocks Spare wheel Glue First-aid kit Spare lamps Universal pliers Vehicle jack Spare fuses Compressor Hazard warning triangle Rep
Index 12 V fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 For Dometic toilet . . . . . . . . . . . . . . . . . . . 138 For the starter battery . . . . . . . . . . . . . . . . 135 For Thetford toilet . . . . . . . . . . . . . . . . . . . 137 On the living area battery . . . . . . . . . . . . . 136 12 V indicator lamp . . . . . . . . . . . . . . . . . 123, 127 12 V main switch . . . . . . . . . . . . . . . 123, 126, 128 12 V power supply . . . . . . . . . . . . . . . . . . . . . .
Index Operating modes . . . . . . . . . . . . . . . . . . . . 165 Safety/drainage valve . . . . . . . . . . . . . . . . 165 Summer operation . . . . . . . . . . . . . . . . . . . 165 Switching off . . . . . . . . . . . . . . . . . . . . . . . . 166 Switching on . . . . . . . . . . . . . . . . . . . . . . . . 166 Troubleshooting . . . . . . . . . . . . . . . . . . . . . 238 Water, filling with . . . . . . . . . . . . . . . . . . . . 166 Winter operation . . . . . . . . . . . . . . . . . . . . .
Index Conversion door . . . . . . . . . . . . . . . . . . . . . 59, 64 Insect screen . . . . . . . . . . . . . . . . . . . . . . . . 64 Roman shade, closing . . . . . . . . . . . . . . . . . 64 Roman shade, opening . . . . . . . . . . . . . . . . 64 Conversion door, inside Locking . . . . . . . . . . . . . . . . . . . . . . . . . 61, 62 Opening . . . . . . . . . . . . . . . . . . . . . . . . . 61, 62 Conversion door, outside Locking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Opening . . . .
Index F Fault current protection switch . . . . . . . . . . . . . 133 Filling the tank . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Fire Behaviour in the event of . . . . . . . . . . . . . . . 19 Extinguishing . . . . . . . . . . . . . . . . . . . . . . . . 19 Fire prevention . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Fire risks, avoidance . . . . . . . . . . . . . . . . . . . . . 19 Fixed bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Closing . . . . . . . . . . .
Index Headrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Heat exchanger (Alde) Switching off . . . . . . . . . . . . . . . . . . . . . . . 150 Switching on . . . . . . . . . . . . . . . . . . . . . . . 150 Heat exchanger (Arizona) Switching off . . . . . . . . . . . . . . . . . . . . . . . 152 Switching on . . . . . . . . . . . . . . . . . . . . . . . 152 Heat exchangers, heater, replacement . . . . . . 139 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index Insect screen, windows Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Insect screen, wind-up skylight Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Inspection records . . . . . . . . . . . . . . . . . . . . . . . . 9 Inspection work . . . . . . . . . . . . . . . . . . . . . . . . 215 Inspections . . . . . . . . . . . . . . .
Index Hot-air heater . . . . . . . . . . . . . . 141, 143, 145 Refrigerator . . . . . . . . 173, 174, 177, 178, 182 Switching automatics, gas system . . . . . . 109 Oven see gas cooker or gas oven . . . . . . 168, 169, 170 Overcab bed . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Access ladder . . . . . . . . . . . . . . . . . . . . . . . 88 Folding downwards . . . . . . . . . . . . . . . . . . . 89 Folding mechanism . . . . . . . . . . . . . . . . . . . 88 Folding upwards . . . . . . . . . . . .
Index Roman shade, cleaning . . . . . . . . . . . . . . . . . . 208 Roman shade, driver's cabin . . . . . . . . . . . . . . . 50 Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Roman shade, Heki skylight Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Opening . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Roman shade, hinged skylight Closing . . . . . . . . . . . . . . . . . . . . . . . .
Index Suspension table . . . . . . . . . . . . . . . . . . . . . 79, 81 Conversion to bed foundation . . . . . . . . 80, 81 Extending . . . . . . . . . . . . . . . . . . . . . . . 80, 81 Reducing size . . . . . . . . . . . . . . . . . . . . 80, 81 Switch for water pump . . . . . . . . . . . . . . . . . . . 190 Switching automatics, gas system . . . . . . . . . 107 Swivel table . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Conversion to bed foundation . . . . . . . . . . .
Index Toilet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245 Vacuum toilet . . . . . . . . . . . . . . . . . . . . . . . 246 Water supply . . . . . . . . . . . . . . . . . . . . . . . 245 TV cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Tyre change see changing wheels . . . . . . . . . . 229 Tyre specifications . . . . . . . . . . . . . . . . . . . . . . 229 Tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Excessive wear . . . . . . . . . . .
Index Roman shade . . . . . . . . . . . . . . . . . . . . . . . 78 Troubleshooting . . . . . . . . . . . . . . . . . . . . 246 Winter care . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 Winter operation . . . . . . . . . . . . . . . . . . . . . . . 210 Writing and reading rest . . . . . . . . . . . . . . . . . .
Index 274 Motorcaravan - 09-08 - DET-0033-07 EN
