Product Info
Table Of Contents
- TABLE OF CONTENTS
- 1 USERS OF THIS MANUAL
- 1.1. Purpose of this manual
- 1.2. End User
- 1.3. Training
- 1.4. Information
- 1.5. Disclaimer
- 2 DigiShot® Plus CE4 Tagger PRODUCT SAFETY
- 2.1. DetNet Safety Philosophy
- 2.2. User Safety
- 2.3. Product Safety
- 2.4. Transportation, Storage and Handling
- 2.5. Maintenance Schedule
- 2.6. Improper Use
- 2.7. Information in case of emergency
- 2.8. Warning, Caution, and Note Statements
- 2.9. RF compliance - FCC (USA) and ICES (Canada)
- 3 DigiShot® Plus CE4 Tagger General Information
- 3.1. Multiple Channel Mode
- 3.2. DigiShot® Plus CE4 Tagger Components
- 3.2.1. Harness wire terminals
- 3.2.2. Pogo pin connector
- 3.2.3. LED’s
- 3.2.4. LCD Screen
- 3.2.5. Soft Keys
- 3.2.6. Navigation and Numerical keys ((((
- 3.2.7. Enter key
- 3.2.8. Backspace Key
- 3.2.9. ESC key
- 3.2.10. ON/OFF key
- 3.2.11. FN key
- 3.2.12. USB connector port
- 3.2.13. Battery
- 3.2.14. Audio Tones
- 3.2.15. Vibration Signals
- 3.2.16. Visual Signals
- 3.2.17. Real Time Clock (RTC) Function
- 3.3. DigiShot® Plus CE4 Tagger Menu Navigation
- 3.4. Systems Notification/Quick info screen
- 4 DigiShot® Plus CE4 Tagger Accessories
- 4.1. External Battery Pack
- 4.2. Replaceable Top Connector
- 4.3. Surface Harness Wire
- 5 DigiShot® Plus CE4 Tagger Battery
- 5.1. Charging the DigiShot® Plus CE4 Tagger
- 5.2. Power DigiShot® Plus CE4 Tagger ON and OFF
- 6 Tagging DigiShot® Plus Detonators
- 6.1. New Design Screen
- 6.2. Tag Detonators
- 6.3. Tagging Screen Soft Key Options
- 6.4. Right or Left Side Definition
- 7 Testing DigiShot® Plus detonators
- 7.1. Test All in List
- 7.2. Test Row
- 7.3. Test Single Detonator
- 7.4. Autosearch
- 7.5. Leakage Test
- 7.6. Untagged Test
- 7.7. Check Pattern
- 8 View Design
- 8.1. View Design Soft Key Options
- 8.2. List Detonators
- 8.3. List Missing detonators
- 8.4. List New Detonators
- 8.5. List bad status
- 8.6. Blast Summary
- 8.7. Det Totals
- 9 System Information
- 10 Configuration Settings
- 10.1. DigiShot® Plus Setup
- 10.2. Device Setup
- 10.3. Advanced Setup
- 11 Troubleshooting
- 11.1. Troubleshooting during Tagging
- 11.2. Troubleshooting during Testing
- 11.3. Basic causes of leakage
- 11.4. Troubleshooting during Installation
- 12 Specifications
- 12.1. Temperature Limitations
- 12.2. Battery Life
- 12.3. Storing the DigiShot® Plus Tagger
- 12.4. Cleaning the DigiShot® Plus Tagger
- 12.5. Electrostatic Discharge, Over Voltage, Over Current and EMP Immunity
- 12.6. Inherent Safety
- 12.7. Safety Warnings
- 12.8. Maximum Dets vs Leakage for successful Blasting
UTM-00330 | Rev 5
Page 48 of 91 DetNet South Africa Copyright © 2019
This function enables the user to search for connected DigiShot
®
Plus detonators and to compare the results
of the search against the stored Detonator List. It performs the same steps as an Autosearch except for the
following:
Check Pattern does not overwrite the Detonator List.
Check Pattern generates a list of detonators that should correlate with the existing detonator list.
Check Pattern generates a list of Missing detonators that were not found when compared to the
detonator list.
Check Pattern generates a list of new detonators found during test, which were not part of the original
detonator list before the test.
Parameters for check pattern will be determined automatically from the list. However, the Autosearch
settings parameters still applies here.
1. Main Menu
Press to select Test Menu
2. Test Menu
Press to select Check Pattern
3. Channel selection
Use the numerical keypad to enter Channel number
Press to continue.
A warning will be displayed if any discrepancies are found once the Check Pattern
function has completed.