Product Info
Table Of Contents
- TABLE OF CONTENTS
- 1 USERS OF THIS MANUAL
- 1.1. Purpose of this manual
- 1.2. End User
- 1.3. Training
- 1.4. Information
- 1.5. Disclaimer
- 2 DigiShot® Plus CE4 Tagger PRODUCT SAFETY
- 2.1. DetNet Safety Philosophy
- 2.2. User Safety
- 2.3. Product Safety
- 2.4. Transportation, Storage and Handling
- 2.5. Maintenance Schedule
- 2.6. Improper Use
- 2.7. Information in case of emergency
- 2.8. Warning, Caution, and Note Statements
- 2.9. RF compliance - FCC (USA) and ICES (Canada)
- 3 DigiShot® Plus CE4 Tagger General Information
- 3.1. Multiple Channel Mode
- 3.2. DigiShot® Plus CE4 Tagger Components
- 3.2.1. Harness wire terminals
- 3.2.2. Pogo pin connector
- 3.2.3. LED’s
- 3.2.4. LCD Screen
- 3.2.5. Soft Keys
- 3.2.6. Navigation and Numerical keys ((((
- 3.2.7. Enter key
- 3.2.8. Backspace Key
- 3.2.9. ESC key
- 3.2.10. ON/OFF key
- 3.2.11. FN key
- 3.2.12. USB connector port
- 3.2.13. Battery
- 3.2.14. Audio Tones
- 3.2.15. Vibration Signals
- 3.2.16. Visual Signals
- 3.2.17. Real Time Clock (RTC) Function
- 3.3. DigiShot® Plus CE4 Tagger Menu Navigation
- 3.4. Systems Notification/Quick info screen
- 4 DigiShot® Plus CE4 Tagger Accessories
- 4.1. External Battery Pack
- 4.2. Replaceable Top Connector
- 4.3. Surface Harness Wire
- 5 DigiShot® Plus CE4 Tagger Battery
- 5.1. Charging the DigiShot® Plus CE4 Tagger
- 5.2. Power DigiShot® Plus CE4 Tagger ON and OFF
- 6 Tagging DigiShot® Plus Detonators
- 6.1. New Design Screen
- 6.2. Tag Detonators
- 6.3. Tagging Screen Soft Key Options
- 6.4. Right or Left Side Definition
- 7 Testing DigiShot® Plus detonators
- 7.1. Test All in List
- 7.2. Test Row
- 7.3. Test Single Detonator
- 7.4. Autosearch
- 7.5. Leakage Test
- 7.6. Untagged Test
- 7.7. Check Pattern
- 8 View Design
- 8.1. View Design Soft Key Options
- 8.2. List Detonators
- 8.3. List Missing detonators
- 8.4. List New Detonators
- 8.5. List bad status
- 8.6. Blast Summary
- 8.7. Det Totals
- 9 System Information
- 10 Configuration Settings
- 10.1. DigiShot® Plus Setup
- 10.2. Device Setup
- 10.3. Advanced Setup
- 11 Troubleshooting
- 11.1. Troubleshooting during Tagging
- 11.2. Troubleshooting during Testing
- 11.3. Basic causes of leakage
- 11.4. Troubleshooting during Installation
- 12 Specifications
- 12.1. Temperature Limitations
- 12.2. Battery Life
- 12.3. Storing the DigiShot® Plus Tagger
- 12.4. Cleaning the DigiShot® Plus Tagger
- 12.5. Electrostatic Discharge, Over Voltage, Over Current and EMP Immunity
- 12.6. Inherent Safety
- 12.7. Safety Warnings
- 12.8. Maximum Dets vs Leakage for successful Blasting
UTM-00330 | Rev 5
Page 66 of 91 DetNet South Africa Copyright © 2019
This function supports the use of NetShock / DriftShot Starter detonators, which will allow the user to interface
to Shocktube / Nonel. To enable this function the user must select ‘Use Starter dets’ in the DigiShot Setup
menu shown below.
1. Main Menu
Press to select Configuration
2. Configuration Menu
Press to select DigiShot Setup
3. DigiShot
®
Setup
Press to select Use Starter dets
4. Use Starter Dets.
Use the arrow key to display the YES /NO option
as required.
Press to continue
Press Soft Key to save and Soft Key to return
to Main Menu
When the ‘Use Starter dets’ feature is activated, the Tagger will scan for Starter
detonators in the Test Single Detonator, Test All, Autosearch and Check Pattern
functions. If found, Starter detonators will also be displayed in the detonator list.