Product Info
Table Of Contents
- TABLE OF CONTENTS
- 1 USERS OF THIS MANUAL
- 1.1. Purpose of this manual
- 1.2. End User
- 1.3. Training
- 1.4. Information
- 1.5. Disclaimer
- 2 DigiShot® Plus CE4 Tagger PRODUCT SAFETY
- 2.1. DetNet Safety Philosophy
- 2.2. User Safety
- 2.3. Product Safety
- 2.4. Transportation, Storage and Handling
- 2.5. Maintenance Schedule
- 2.6. Improper Use
- 2.7. Information in case of emergency
- 2.8. Warning, Caution, and Note Statements
- 2.9. RF compliance - FCC (USA) and ICES (Canada)
- 3 DigiShot® Plus CE4 Tagger General Information
- 3.1. Multiple Channel Mode
- 3.2. DigiShot® Plus CE4 Tagger Components
- 3.2.1. Harness wire terminals
- 3.2.2. Pogo pin connector
- 3.2.3. LED’s
- 3.2.4. LCD Screen
- 3.2.5. Soft Keys
- 3.2.6. Navigation and Numerical keys ((((
- 3.2.7. Enter key
- 3.2.8. Backspace Key
- 3.2.9. ESC key
- 3.2.10. ON/OFF key
- 3.2.11. FN key
- 3.2.12. USB connector port
- 3.2.13. Battery
- 3.2.14. Audio Tones
- 3.2.15. Vibration Signals
- 3.2.16. Visual Signals
- 3.2.17. Real Time Clock (RTC) Function
- 3.3. DigiShot® Plus CE4 Tagger Menu Navigation
- 3.4. Systems Notification/Quick info screen
- 4 DigiShot® Plus CE4 Tagger Accessories
- 4.1. External Battery Pack
- 4.2. Replaceable Top Connector
- 4.3. Surface Harness Wire
- 5 DigiShot® Plus CE4 Tagger Battery
- 5.1. Charging the DigiShot® Plus CE4 Tagger
- 5.2. Power DigiShot® Plus CE4 Tagger ON and OFF
- 6 Tagging DigiShot® Plus Detonators
- 6.1. New Design Screen
- 6.2. Tag Detonators
- 6.3. Tagging Screen Soft Key Options
- 6.4. Right or Left Side Definition
- 7 Testing DigiShot® Plus detonators
- 7.1. Test All in List
- 7.2. Test Row
- 7.3. Test Single Detonator
- 7.4. Autosearch
- 7.5. Leakage Test
- 7.6. Untagged Test
- 7.7. Check Pattern
- 8 View Design
- 8.1. View Design Soft Key Options
- 8.2. List Detonators
- 8.3. List Missing detonators
- 8.4. List New Detonators
- 8.5. List bad status
- 8.6. Blast Summary
- 8.7. Det Totals
- 9 System Information
- 10 Configuration Settings
- 10.1. DigiShot® Plus Setup
- 10.2. Device Setup
- 10.3. Advanced Setup
- 11 Troubleshooting
- 11.1. Troubleshooting during Tagging
- 11.2. Troubleshooting during Testing
- 11.3. Basic causes of leakage
- 11.4. Troubleshooting during Installation
- 12 Specifications
- 12.1. Temperature Limitations
- 12.2. Battery Life
- 12.3. Storing the DigiShot® Plus Tagger
- 12.4. Cleaning the DigiShot® Plus Tagger
- 12.5. Electrostatic Discharge, Over Voltage, Over Current and EMP Immunity
- 12.6. Inherent Safety
- 12.7. Safety Warnings
- 12.8. Maximum Dets vs Leakage for successful Blasting
UTM-00330 | Rev 5
Page 73 of 91 DetNet South Africa Copyright © 2019
This function enables the user to clear the detonator memory and remove the tag that was assigned.
Connect the harness wire to the Harness wire terminals of the Tagger. The detonators should remain
connected to the Harness wire.
1. Main Menu
Press to select Configuration Settings.
2. Configuration Settings Menu
Press to select Advanced Setup.
Use numerical keypad to enter Unique Tagger Password.
Press ENTER to continue.
3. Advanced Setup
Press to select Clear Tags
4. Clear Tags
An information screen will be displayed.
Press Soft Key to erase all detonators tags for connected detonators.
Press Soft Key to exit without clearing detonators.
5. Det tags cleared message will be displayed to indicate that Tags have been
cleared.
6. Press OK Soft Key to return to Advanced Setup Menu.
Use this feature with caution. Once all det tags were cleared, the detonators may need
to be re-tagged from the start, which will be time consuming.