Product Info
Table Of Contents
- TABLE OF CONTENTS
- 1 USERS OF THIS MANUAL
- 1.1. Purpose of this manual
- 1.2. End User
- 1.3. Training
- 1.4. Information
- 1.5. Disclaimer
- 2 DigiShot® Plus CE4 Tagger PRODUCT SAFETY
- 2.1. DetNet Safety Philosophy
- 2.2. User Safety
- 2.3. Product Safety
- 2.4. Transportation, Storage and Handling
- 2.5. Maintenance Schedule
- 2.6. Improper Use
- 2.7. Information in case of emergency
- 2.8. Warning, Caution, and Note Statements
- 2.9. RF compliance - FCC (USA) and ICES (Canada)
- 3 DigiShot® Plus CE4 Tagger General Information
- 3.1. Multiple Channel Mode
- 3.2. DigiShot® Plus CE4 Tagger Components
- 3.2.1. Harness wire terminals
- 3.2.2. Pogo pin connector
- 3.2.3. LED’s
- 3.2.4. LCD Screen
- 3.2.5. Soft Keys
- 3.2.6. Navigation and Numerical keys ((((
- 3.2.7. Enter key
- 3.2.8. Backspace Key
- 3.2.9. ESC key
- 3.2.10. ON/OFF key
- 3.2.11. FN key
- 3.2.12. USB connector port
- 3.2.13. Battery
- 3.2.14. Audio Tones
- 3.2.15. Vibration Signals
- 3.2.16. Visual Signals
- 3.2.17. Real Time Clock (RTC) Function
- 3.3. DigiShot® Plus CE4 Tagger Menu Navigation
- 3.4. Systems Notification/Quick info screen
- 4 DigiShot® Plus CE4 Tagger Accessories
- 4.1. External Battery Pack
- 4.2. Replaceable Top Connector
- 4.3. Surface Harness Wire
- 5 DigiShot® Plus CE4 Tagger Battery
- 5.1. Charging the DigiShot® Plus CE4 Tagger
- 5.2. Power DigiShot® Plus CE4 Tagger ON and OFF
- 6 Tagging DigiShot® Plus Detonators
- 6.1. New Design Screen
- 6.2. Tag Detonators
- 6.3. Tagging Screen Soft Key Options
- 6.4. Right or Left Side Definition
- 7 Testing DigiShot® Plus detonators
- 7.1. Test All in List
- 7.2. Test Row
- 7.3. Test Single Detonator
- 7.4. Autosearch
- 7.5. Leakage Test
- 7.6. Untagged Test
- 7.7. Check Pattern
- 8 View Design
- 8.1. View Design Soft Key Options
- 8.2. List Detonators
- 8.3. List Missing detonators
- 8.4. List New Detonators
- 8.5. List bad status
- 8.6. Blast Summary
- 8.7. Det Totals
- 9 System Information
- 10 Configuration Settings
- 10.1. DigiShot® Plus Setup
- 10.2. Device Setup
- 10.3. Advanced Setup
- 11 Troubleshooting
- 11.1. Troubleshooting during Tagging
- 11.2. Troubleshooting during Testing
- 11.3. Basic causes of leakage
- 11.4. Troubleshooting during Installation
- 12 Specifications
- 12.1. Temperature Limitations
- 12.2. Battery Life
- 12.3. Storing the DigiShot® Plus Tagger
- 12.4. Cleaning the DigiShot® Plus Tagger
- 12.5. Electrostatic Discharge, Over Voltage, Over Current and EMP Immunity
- 12.6. Inherent Safety
- 12.7. Safety Warnings
- 12.8. Maximum Dets vs Leakage for successful Blasting
UTM-00330 | Rev 5
Page 91 of 91 DetNet South Africa Copyright © 2019
Batteries may leak or explode if incorrectly handled.
Only use batteries approved for use in the DigiShot
®
Plus Tagger.
Do not expose the battery to an open flame or excessive heat.
Replacing external batteries in the battery pack must be done in a safe and dry place to prevent ingress of
moisture or condensation into the battery pack enclosure.
Do not apply undue pressure to the LCD screen as this could damage the Tagger or cause a malfunction.
Should the LCD screen break, care should be taken to avoid injury from broken glass and to prevent liquid
crystal from the screen touching the skin or entering the eyes and mouth.
High leakage levels can result in misfires of the DigiShot
®
Plus detonators. Refer to
the scalability chart contained in UTM-00329 - Additional System Information for
detailed information.