Operators Manual
Table Of Contents
- California Proposition 65 Warning and Engine Idle Notice
- Forward
- To the Operator
- Caution Summary
- Engine Identification
- Operating Instructions for Starting the Engine
- First Time Start Preparations
- System Checks
- Starting the Engine for the First Time
- Starting the Engine
- Running the Engine
- Stopping the Engine
- Emergency Jump Starting
- Routine Engine Start
- Monitoring the Engine Operation
- Changing the Idle Speed
- Shutting Down the Engine after High Load Operation
- Emergency Running Mode
- Stop Engine Override Option
- Cold Weather Operation
- First Time Start Preparations
- Detroit Diesel Electronic Controls (DDEC) System
- Engine Brake System
- Engine Systems
- EPA07 Aftertreatment Device
- EPA10 Aftertreatment System
- GHG14 Aftertreatment System
- GHG17 Aftertreatment System
- Diesel Exhaust Fluid Information
- Aftertreatment Device Operating Requirements
- EPA10 Diesel Exhaust Fluid (DEF) Purge Cycle
- EPA10/GHG14/GHG17 Diesel Exhaust Fluid Tank
- Aftertreatment Maintenance
- Performing a Parked Regeneration - EPA07
- Performing a Parked Regeneration - EPA10/GHG14
- Performing a Parked Regeneration
- Hazardous Applications
- Service Record
- Instrument Panel Lamps
- Diesel Exhaust Fluid Level Warning Lamps
- Aftertreatment System Driver Notifications and Actions
- DEF Post-Run Indicator Lamp
- Preventive Maintenance Intervals
- EPA07/EPA10/GHG14/GHG17 Preventive Maintenance Tables - 93K222(CK-4) and 93K223(FA-4)
- EPA07/EPA10/GHG14/GHG17 Preventive Maintenance Tables - 93K218(CJ-4)
- EPA07/EPA10/GHG14/GHG17 Preventive Maintenance Tables for Recreational Vehicles
- Routine Preventive Maintenance
- Monitoring the Lubricating Oil
- Monitoring the Lubricating Oil Filter
- Monitoring the Cooling System
- Inspection of the Radiator
- Monitoring the Cooling System Filter
- Monitoring the Fuel Filters
- Adjusting the Valve Lash
- Monitoring the Belt Tensioner
- Poly-V-Belt Inspection
- Monitoring the Serpentine Belts
- Inspection of the Air Intake System
- Monitoring the Air Cleaner
- Monitoring the Exhaust System
- Monitoring the Aftertreatment System
- Inspection of the Air Compressor
- Monitoring the Fuel and Fuel Tank
- Inspection of Hoses and Fittings for Fuel Leaks
- Inspection of the Turbocharger and Charge Air Cooler
- Inspection of the Battery
- Steam Cleaning the Engine
- Inspection of the Battery-Charging Alternator
- Lubricating the Fan Hub
- Checking the Vibration Damper
- How to Procedures
- How to Select Lubricating Oil
- How to Select Lubricating Oil (EPA07)
- When to Change Oil
- How to Replace the Lubricating Oil and Oil Filter
- How to Select Diesel Fuel
- How to Replace the Fuel Filters
- Removal of the Fuel Prefilter - Two-Filter System
- Installation of the Fuel Prefilter - Two-Filter System
- Removal of the Water Coalescer/Final Filter - Two-Filter System
- Installation of the Coalescer/Final Filter - Two-Filter System
- Removal of the Final Filter - Three-Filter System
- Installation of the Final Filter - Three-Filter System
- Removal of the Prefilter - Three-Filter System
- Installation of the Prefilter - Three-Filter System
- Removal of the Water Separator/Coalescer - Three-Filter System
- Installation of the Water Separator/Coalescer - Three-Filter System
- Engine Out of Fuel – How to Restart
- How to Clean an Engine
- Cleaning/Flushing the Cooling System
- Coolant Selections and Maintenance
- Coolant Fill Options
- Coolants for Detroit™ Engines
- Maintenance
- Appendix A - Definitions
- Appendix B - General Coolant Information
- Appendix C - Detroit™ Cooling System Maintenance Products
- How to Replace the Coolant Filter
- Checking the Hoses
- How to Service the Dry Type Air Cleaner
- Customer Assistance
- Detroit Genuine Coolant Engine Products
- Engine Oil Capacities
When the parked regeneration request is accepted, the Diesel Particulate Filter
(DPF) Regeneration lamp will turn ON one time for one second and then turn off
for the remainder of the parked regeneration. The High Exhaust System
Temperature (HEST) lamp will flash for one second every ten seconds and
eventually become solid when the tailpipe temperature is above 525°C (977°F).
The engine speed may vary during parked regeneration (depending on engine
displacement, exhaust temperature and the amount of soot accumulated in the
DPF). The regeneration is complete when the engine returns to low idle and the
DPF lamp remains OFF. The HEST lamp will remain ON, but the vehicle may be
driven.
NOTE: A parked regeneration will STOP and the engine will return to low
idle if any of the following happens:
• The key is turned to the OFF position
• The vehicle is put into gear
• The clutch is cycled
• The parking brake is released
NOTE: If a parked regeneration is being performed to check NOx
conversion, the calculated ambient temperature in the ACM (AS053) must
be above 0°C (32°F) or the test will fail.
NOTE: If the HEST LAMP is FLASHING, regeneration is in process and the
system is coming up to temperature.
1. Keep engine at slow idle (cannot be in Fast Idle or PTO Mode). Put
transmission in neutral (if equipped with an automatic transmission, cycle it
into gear and then back to neutral).
2. Set park brake (cycle the park brake OFF then ON).
3. Press and release clutch pedal once per ignition cycle (if configured).
4. Hold DPF Switch to the ON position for five seconds and then release
(engine speed will increase and DPF lamp will go out).
DD Heavy Duty Platform Operators Manual
All information subject to change without notice. 101
DDC-SVC-MAN-0189 Copyright © 2022 DETROIT DIESEL CORPORATION