Operators Manual
Table Of Contents
- California Proposition 65 Warning and Engine Idle Notice
- Forward
- To the Operator
- Caution Summary
- Engine Identification
- Operating Instructions for Starting the Engine
- First Time Start Preparations
- System Checks
- Starting the Engine for the First Time
- Starting the Engine
- Running the Engine
- Stopping the Engine
- Emergency Jump Starting
- Routine Engine Start
- Monitoring the Engine Operation
- Changing the Idle Speed
- Shutting Down the Engine after High Load Operation
- Emergency Running Mode
- Stop Engine Override Option
- Cold Weather Operation
- First Time Start Preparations
- Detroit Diesel Electronic Controls (DDEC) System
- Engine Brake System
- Engine Systems
- EPA07 Aftertreatment Device
- EPA10 Aftertreatment System
- GHG14 Aftertreatment System
- GHG17 Aftertreatment System
- Diesel Exhaust Fluid Information
- Aftertreatment Device Operating Requirements
- EPA10 Diesel Exhaust Fluid (DEF) Purge Cycle
- EPA10/GHG14/GHG17 Diesel Exhaust Fluid Tank
- Aftertreatment Maintenance
- Performing a Parked Regeneration - EPA07
- Performing a Parked Regeneration - EPA10/GHG14
- Performing a Parked Regeneration
- Hazardous Applications
- Service Record
- Instrument Panel Lamps
- Diesel Exhaust Fluid Level Warning Lamps
- Aftertreatment System Driver Notifications and Actions
- DEF Post-Run Indicator Lamp
- Preventive Maintenance Intervals
- EPA07/EPA10/GHG14/GHG17 Preventive Maintenance Tables - 93K222(CK-4) and 93K223(FA-4)
- EPA07/EPA10/GHG14/GHG17 Preventive Maintenance Tables - 93K218(CJ-4)
- EPA07/EPA10/GHG14/GHG17 Preventive Maintenance Tables for Recreational Vehicles
- Routine Preventive Maintenance
- Monitoring the Lubricating Oil
- Monitoring the Lubricating Oil Filter
- Monitoring the Cooling System
- Inspection of the Radiator
- Monitoring the Cooling System Filter
- Monitoring the Fuel Filters
- Adjusting the Valve Lash
- Monitoring the Belt Tensioner
- Poly-V-Belt Inspection
- Monitoring the Serpentine Belts
- Inspection of the Air Intake System
- Monitoring the Air Cleaner
- Monitoring the Exhaust System
- Monitoring the Aftertreatment System
- Inspection of the Air Compressor
- Monitoring the Fuel and Fuel Tank
- Inspection of Hoses and Fittings for Fuel Leaks
- Inspection of the Turbocharger and Charge Air Cooler
- Inspection of the Battery
- Steam Cleaning the Engine
- Inspection of the Battery-Charging Alternator
- Lubricating the Fan Hub
- Checking the Vibration Damper
- How to Procedures
- How to Select Lubricating Oil
- How to Select Lubricating Oil (EPA07)
- When to Change Oil
- How to Replace the Lubricating Oil and Oil Filter
- How to Select Diesel Fuel
- How to Replace the Fuel Filters
- Removal of the Fuel Prefilter - Two-Filter System
- Installation of the Fuel Prefilter - Two-Filter System
- Removal of the Water Coalescer/Final Filter - Two-Filter System
- Installation of the Coalescer/Final Filter - Two-Filter System
- Removal of the Final Filter - Three-Filter System
- Installation of the Final Filter - Three-Filter System
- Removal of the Prefilter - Three-Filter System
- Installation of the Prefilter - Three-Filter System
- Removal of the Water Separator/Coalescer - Three-Filter System
- Installation of the Water Separator/Coalescer - Three-Filter System
- Engine Out of Fuel – How to Restart
- How to Clean an Engine
- Cleaning/Flushing the Cooling System
- Coolant Selections and Maintenance
- Coolant Fill Options
- Coolants for Detroit™ Engines
- Maintenance
- Appendix A - Definitions
- Appendix B - General Coolant Information
- Appendix C - Detroit™ Cooling System Maintenance Products
- How to Replace the Coolant Filter
- Checking the Hoses
- How to Service the Dry Type Air Cleaner
- Customer Assistance
- Detroit Genuine Coolant Engine Products
- Engine Oil Capacities
4. Check the engine for leaks.
a. Check all hoses, hose clamps, and pipe unions on the engine for
tightness. Shut down the engine and tighten them if necessary.
b. Check the oil feed and return lines at the turbocharger for leaks. Shut
down the engine and tighten them if necessary.
5. Shut down the engine.
NOTE: If the engine operating temperature is below 60ºC (140ºF), the
engine must be on a level surface and then shut down for 60 minutes for an
accurate oil level reading. Otherwise, the engine must be brought up to an
operating temperature of 60ºC (140ºF), parked on a level surface and then
shut down for five minutes for an accurate oil level reading.
6. Check the oil level using the oil dipstick. The oil level is measured using the
crosshatch area on the dipstick. If the oil reading within the crosshatch area,
then the oil is at the proper level for engine operation.
7. Check all the mounting fasteners on the engine for tightness.
Checking the Coolant Level (Cold Check)
Check coolant level as follows:
1. Ensure that all coolant plugs in the bottom of the radiator and on the
radiator outlet pipe are secure and tight.
2. Check the coolant level. The cooling system is correctly filled when the
coolant is between the full and low marks on the surge tank.
Operating Instructions for Starting the Engine
52 All information subject to change without notice.
Copyright © 2022 DETROIT DIESEL CORPORATION DDC-SVC-MAN-0189