Data Sheet

ManualsBrandsDevantech ManualsInfrared Range FindersGP2Y0E02A IR Range Sensor - 4cm to 50cm (Analogue Output)

Sheet No. : OP13003EN

Notice The content of data sheet is subject to change without prior notice.

In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP

devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.

GP2Y0E02A

Distance Measuring Sensor Unit

Measuring distance : 4 to 50 cm

Analog output type

■Features

■Description ■Agency approvals/Compliance

1. Infrared LED and CMOS image sensor with

built-in signal processing circuit

2. Distance measuring range : 4 to 50 cm

3. Low voltage operation : Min 2.7V

4. Compact size (18.9 × 8.0 × 5.2mm)

5. High-precision measurement

6. Analog output type

GP2Y0E02A is a distance measuring sensor unit,

composed of an integrated combination of CMOS

image sensor and IR-LED.

The variety of the reflectivity of the object, the

environmental temperature and the operating duration

are not influenced easily to the distance detection

because of adopting the triangulation method.

This device outputs the voltage corresponding to the

detection distance. So this sensor can also be used as

a proximity sensor.

1. Compliant with RoHS directive (2002/95/EC)

■Applications

1. Cleaning Robot

2. Human type Robot

3. Touch-less switch

(Sanitary equipment, Control of illumination, etc)

4. Sensor for energy saving

(ATM, Copier, LCD monitor, etc)

5. Amusement equipment

(Robot, game machine, etc)

Summary of content (9 pages)

PAGE 1
GP2Y0E02A GP2Y0E02A Distance Measuring Sensor Unit Measuring distance : 4 to 50 cm Analog output type ■Description ■Agency approvals/Compliance GP2Y0E02A is a distance measuring sensor unit, composed of an integrated combination of CMOS image sensor and IR-LED. The variety of the reflectivity of the object, the environmental temperature and the operating duration are not influenced easily to the distance detection because of adopting the triangulation method.
PAGE 2
GP2Y0E02A ■Schematic ① VDD ② GND ③ Vout(A) ④ GPIO1 Please use an electric source with an output current of 150mA or more because LED pulse current is more than 100mA. ■Outline (Drawing No.CY15126i02) Scale : 5/1 Unit : mm Sheet No.
PAGE 3
GP2Y0E02A ■Absolute maximum ratings Parameter Supply voltage Output terminal voltage Output current Input terminal voltage Operating temperature Storage temperature Symbol VDD Vout (A) Iout (A) GPIO1 Topr Tstg Ratings -0.3 to + 3.6 -0.3 to +2.8 -6.0 to +6.0 -0.3 to VDD+0.
PAGE 4
GP2Y0E02A ■Timing Chart Active / Stand-by timing sequence GPIO1 is set High or Low to control Active/stand-by state. GPIO1=high : Active state GPIO1=Low : Stand-by state VDD GPIO1 T1 T1 T2 T2 Description GPIO1 power delay after VDD power on GPIO1 leading to VDD power off Min 0 0 Max - Unit ms ms GPIO1 should be set after or at the same time VDD has turned on. In case that VDD turn off, GPIO1 should be pull low.
PAGE 5
GP2Y0E02A ■Notes [Advice for the optics] ●Lens of this device shall be kept cleanly. There are cases that dust, water or oil and so on deteriorate the characteristics of this device. Please consider in actual application. ●In case that protection cover is set in front of this sensor , the protection cover shall be recommended to use material which doesn’t scatter light and be matt finish.
PAGE 6
GP2Y0E02A [Advice for the characteristics] ●In case that there is an object near to light exits of the sensor between the sensor and the detected object, please use this device after confirming sufficiently what the characteristics of this sensor do not change by the object. ●This product has the function to remove disturbance light by the cancellation function of ambient light, a visible light cut lens, etc.
PAGE 7
GP2Y0E02A ■Compliance with each regulation 1. The RoHS directive(2002/95/EC) This product complies with the RoHS directive(2002/95/EC) . Object substances: mercury, lead (except for lead in high melting temperature type solders and glass of electronic components), cadmium, hexavalent chromium, polybrominated biphenyls (PBB) and polybrominated diphenyl ethers (PBDE) 2.
PAGE 8
GP2Y0E02A ■Packing specification (Drawing No. CY15127i09) Pads (11 pieces) Product Tray 10 sheets of tray Packing case Indication side. (1) Packing number Max 100 pieces per tray Max 1000 pieces per case (2) Close the lid of case and seals with craft tape, and fill in the blanks of Model No., quantity and date. (3) Outside : 286 x 173 x 105 (mm) (4) Indication The content of the indication conforms to EIAJ C-3 and the following items are indicated. Model No.
PAGE 9
GP2Y0E02A ■Important Notices · The circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.